Mini Classifieds

Pinto or Bobcat wagon wanted
Date: 08/05/2018 10:49 pm
79-80 full glass hatch

Date: 01/04/2017 04:04 am
Looking for Plastic? sloping headlight buckets for 77/78
Date: 06/19/2018 03:58 pm
parting out 1975 & 80 pintos
Date: 08/24/2018 02:50 pm
Looking for front seats
Date: 08/10/2021 09:54 pm
'79 Ford Pinto, Green,

Date: 10/29/2019 11:50 am
turbo 4 cyl and aod trans
Date: 12/14/2019 04:55 pm
Drivers side door panel Orange
Date: 05/22/2018 02:27 pm
1977 Pinto for parts

Date: 10/10/2018 06:25 pm

Why the Ford Pinto didn’t suck

Why the Ford Pinto didn't suckThe Ford Pinto was born a low-rent, stumpy thing in Dearborn 40 years ago and grew to become one of the most infamous cars in history. The thing is that it didn't actually suck. Really.

Even after four decades, what's the first thing that comes to mind when most people think of the Ford Pinto? Ka-BLAM! The truth is the Pinto was more than that — and this is the story of how the exploding Pinto became a pre-apocalyptic narrative, how the myth was exposed, and why you should race one.

The Pinto was CEO Lee Iacocca's baby, a homegrown answer to the threat of compact-sized economy cars from Japan and Germany, the sales of which had grown significantly throughout the 1960s. Iacocca demanded the Pinto cost under $2,000, and weigh under 2,000 pounds. It was an all-hands-on-deck project, and Ford got it done in 25 months from concept to production.

Building its own small car meant Ford's buyers wouldn't have to hew to the Japanese government's size-tamping regulations; Ford would have the freedom to choose its own exterior dimensions and engine sizes based on market needs (as did Chevy with the Vega and AMC with the Gremlin). And people cold dug it.

When it was unveiled in late 1970 (ominously on September 11), US buyers noted the Pinto's pleasant shape — bringing to mind a certain tailless amphibian — and interior layout hinting at a hipster's sunken living room. Some call it one of the ugliest cars ever made, but like fans of Mischa Barton, Pinto lovers care not what others think. With its strong Kent OHV four (a distant cousin of the Lotus TwinCam), the Pinto could at least keep up with its peers, despite its drum brakes and as long as one looked past its Russian-roulette build quality.

But what of the elephant in the Pinto's room? Yes, the whole blowing-up-on-rear-end-impact thing. It all started a little more than a year after the Pinto's arrival.

 

Grimshaw v. Ford Motor Company

On May 28, 1972, Mrs. Lilly Gray and 13-year-old passenger Richard Grimshaw, set out from Anaheim, California toward Barstow in Gray's six-month-old Ford Pinto. Gray had been having trouble with the car since new, returning it to the dealer several times for stalling. After stopping in San Bernardino for gasoline, Gray got back on I-15 and accelerated to around 65 mph. Approaching traffic congestion, she moved from the left lane to the middle lane, where the car suddenly stalled and came to a stop. A 1962 Ford Galaxie, the driver unable to stop or swerve in time, rear-ended the Pinto. The Pinto's gas tank was driven forward, and punctured on the bolts of the differential housing.

As the rear wheel well sections separated from the floor pan, a full tank of fuel sprayed straight into the passenger compartment, which was engulfed in flames. Gray later died from congestive heart failure, a direct result of being nearly incinerated, while Grimshaw was burned severely and left permanently disfigured. Grimshaw and the Gray family sued Ford Motor Company (among others), and after a six-month jury trial, verdicts were returned against Ford Motor Company. Ford did not contest amount of compensatory damages awarded to Grimshaw and the Gray family, and a jury awarded the plaintiffs $125 million, which the judge in the case subsequently reduced to the low seven figures. Other crashes and other lawsuits followed.

Why the Ford Pinto didn't suck

Mother Jones and Pinto Madness

In 1977, Mark Dowie, business manager of Mother Jones magazine published an article on the Pinto's "exploding gas tanks." It's the same article in which we first heard the chilling phrase, "How much does Ford think your life is worth?" Dowie had spent days sorting through filing cabinets at the Department of Transportation, examining paperwork Ford had produced as part of a lobbying effort to defeat a federal rear-end collision standard. That's where Dowie uncovered an innocuous-looking memo entitled "Fatalities Associated with Crash-Induced Fuel Leakage and Fires."

The Car Talk blog describes why the memo proved so damning.

In it, Ford's director of auto safety estimated that equipping the Pinto with [an] $11 part would prevent 180 burn deaths, 180 serious burn injuries and 2,100 burned cars, for a total cost of $137 million. Paying out $200,000 per death, $67,000 per injury and $700 per vehicle would cost only $49.15 million.

The government would, in 1978, demand Ford recall the million or so Pintos on the road to deal with the potential for gas-tank punctures. That "smoking gun" memo would become a symbol for corporate callousness and indifference to human life, haunting Ford (and other automakers) for decades. But despite the memo's cold calculations, was Ford characterized fairly as the Kevorkian of automakers?

Perhaps not. In 1991, A Rutgers Law Journal report [PDF] showed the total number of Pinto fires, out of 2 million cars and 10 years of production, stalled at 27. It was no more than any other vehicle, averaged out, and certainly not the thousand or more suggested by Mother Jones.

Why the Ford Pinto didn't suck

The big rebuttal, and vindication?

But what of the so-called "smoking gun" memo Dowie had unearthed? Surely Ford, and Lee Iacocca himself, were part of a ruthless establishment who didn't care if its customers lived or died, right? Well, not really. Remember that the memo was a lobbying document whose audience was intended to be the NHTSA. The memo didn't refer to Pintos, or even Ford products, specifically, but American cars in general. It also considered rollovers not rear-end collisions. And that chilling assignment of value to a human life? Indeed, it was federal regulators who often considered that startling concept in their own deliberations. The value figure used in Ford's memo was the same one regulators had themselves set forth.

In fact, measured by occupant fatalities per million cars in use during 1975 and 1976, the Pinto's safety record compared favorably to other subcompacts like the AMC Gremlin, Chevy Vega, Toyota Corolla and VW Beetle.

And what of Mother Jones' Dowie? As the Car Talk blog points out, Dowie now calls the Pinto, "a fabulous vehicle that got great gas mileage," if not for that one flaw: The legendary "$11 part."

Why the Ford Pinto didn't suck

Pinto Racing Doesn't Suck

Back in 1974, Car and Driver magazine created a Pinto for racing, an exercise to prove brains and common sense were more important than an unlimited budget and superstar power. As Patrick Bedard wrote in the March, 1975 issue of Car and Driver, "It's a great car to drive, this Pinto," referring to the racer the magazine prepared for the Goodrich Radial Challenge, an IMSA-sanctioned road racing series for small sedans.

Why'd they pick a Pinto over, say, a BMW 2002 or AMC Gremlin? Current owner of the prepped Pinto, Fox Motorsports says it was a matter of comparing the car's frontal area, weight, piston displacement, handling, wheel width, and horsepower to other cars of the day that would meet the entry criteria. (Racers like Jerry Walsh had by then already been fielding Pintos in IMSA's "Baby Grand" class.)

Bedard, along with Ron Nash and company procured a 30,000-mile 1972 Pinto two-door to transform. In addition to safety, chassis and differential mods, the team traded a 200-pound IMSA weight penalty for the power gain of Ford's 2.3-liter engine, which Bedard said "tipped the scales" in the Pinto's favor. But according to Bedard, it sounds like the real advantage was in the turns, thanks to some add-ons from Mssrs. Koni and Bilstein.

"The Pinto's advantage was cornering ability," Bedard wrote. "I don't think there was another car in the B. F. Goodrich series that was quicker through the turns on a dry track. The steering is light and quick, and the suspension is direct and predictable in a way that street cars never can be. It never darts over bumps, the axle is perfectly controlled and the suspension doesn't bottom."

Need more proof of the Pinto's lack of suck? Check out the SCCA Washington, DC region's spec-Pinto series.

Members
Stats
  • Total Posts: 139,575
  • Total Topics: 16,267
  • Online today: 2,670
  • Online ever: 2,670 (Today at 01:57:20 AM)
Users Online
  • Users: 0
  • Guests: 451
  • Total: 451
F&I...more

My Somewhat Begrudging Apology To Ford Pinto

ford-pinto.jpg

I never thought I’d offer an apology to the Ford Pinto, but I guess I owe it one.

I had a Pinto in the 1970s. Actually, my wife bought it a few months before we got married. The car became sort of a wedding dowry. So did the remaining 80% of the outstanding auto loan.

During a relatively brief ownership, the Pinto’s repair costs exceeded the original price of the car. It wasn’t a question of if it would fail, but when. And where. Sometimes, it simply wouldn’t start in the driveway. Other times, it would conk out at a busy intersection.

It ranks as the worst car I ever had. That was back when some auto makers made quality something like Job 100, certainly not Job 1.

Despite my bad Pinto experience, I suppose an apology is in order because of a recent blog I wrote. It centered on Toyota’s sudden-acceleration problems. But in discussing those, I invoked the memory of exploding Pintos, perpetuating an inaccuracy.

The widespread allegation was that, due to a design flaw, Pinto fuel tanks could readily blow up in rear-end collisions, setting the car and its occupants afire.

People started calling the Pinto “the barbecue that seats four.” And the lawsuits spread like wild fire.

Responding to my blog, a Ford (“I would very much prefer to keep my name out of print”) manager contacted me to set the record straight.

He says exploding Pintos were a myth that an investigation debunked nearly 20 years ago. He cites Gary Schwartz’ 1991 Rutgers Law Review paper that cut through the wild claims and examined what really happened.

Schwartz methodically determined the actual number of Pinto rear-end explosion deaths was not in the thousands, as commonly thought, but 27.

In 1975-76, the Pinto averaged 310 fatalities a year. But the similar-size Toyota Corolla averaged 313, the VW Beetle 374 and the Datsun 1200/210 came in at 405.

Yes, there were cases such as a Pinto exploding while parked on the shoulder of the road and hit from behind by a speeding pickup truck. But fiery rear-end collisions comprised only 0.6% of all fatalities back then, and the Pinto had a lower death rate in that category than the average compact or subcompact, Schwartz said after crunching the numbers. Nor was there anything about the Pinto’s rear-end design that made it particularly unsafe.

Not content to portray the Pinto as an incendiary device, ABC’s 20/20 decided to really heat things up in a 1978 broadcast containing “startling new developments.” ABC breathlessly reported that, not just Pintos, but fullsize Fords could blow up if hit from behind.

20/20 thereupon aired a video, shot by UCLA researchers, showing a Ford sedan getting rear-ended and bursting into flames. A couple of problems with that video:

One, it was shot 10 years earlier.

Two, the UCLA researchers had openly said in a published report that they intentionally rigged the vehicle with an explosive.

That’s because the test was to determine how a crash fire affected the car’s interior, not to show how easily Fords became fire balls. They said they had to use an accelerant because crash blazes on their own are so rare. They had tried to induce a vehicle fire in a crash without using an igniter, but failed.

ABC failed to mention any of that when correspondent Sylvia Chase reported on “Ford’s secret rear-end crash tests.”

We could forgive ABC for that botched reporting job. After all, it was 32 years ago. But a few weeks ago, ABC, in another one of its rigged auto exposes, showed video of a Toyota apparently accelerating on its own.

Turns out, the “runaway” vehicle had help from an associate professor. He built a gizmo with an on-off switch to provide acceleration on demand. Well, at least ABC didn’t show the Toyota slamming into a wall and bursting into flames.

In my blog, I also mentioned that Ford’s woes got worse in the 1970s with the supposed uncovering of an internal memo by a Ford attorney who allegedly calculated it would cost less to pay off wrongful-death suits than to redesign the Pinto.

It became known as the “Ford Pinto memo,” a smoking gun. But Schwartz looked into that, too. He reported the memo did not pertain to Pintos or any Ford products. Instead, it had to do with American vehicles in general.

It dealt with rollovers, not rear-end crashes. It did not address tort liability at all, let alone advocate it as a cheaper alternative to a redesign. It put a value to human life because federal regulators themselves did so.

The memo was meant for regulators’ eyes only. But it was off to the races after Mother Jones magazine got a hold of a copy and reported what wasn’t the case.

The exploding-Pinto myth lives on, largely because more Americans watch 20/20 than read the Rutgers Law Review. One wonders what people will recollect in 2040 about Toyota’s sudden accelerations, which more and more look like driver error and, in some cases, driver shams.

So I guess I owe the Pinto an apology. But it’s half-hearted, because my Pinto gave me much grief, even though, as the Ford manager notes, “it was a cheap car, built long ago and lots of things have changed, almost all for the better.”

Here goes: If I said anything that offended you, Pinto, I’m sorry. And thanks for not blowing up on me.

2007, 3rd National Pinto Meet

Started by Original74, July 30, 2006, 02:42:08 PM

Previous topic - Next topic

0 Members and 1 Guest are viewing this topic.

73pintogeek

As long as everyone is pushing for their neck of the wood`s...I`d have to say Sacramento,Calif. But then I am a bit biased...not everyone want`s to or can travel 2500-3000 mile`s for an event...I just figure it`s kinda central for those of us on the West coast...Let`s face it...not all of us will be happy with where it is!
Just my two cent`s worth! :neutral:
Where ever it is I`ll do my best to be there...Oh Yeah! ;D
Da Geek...
A bad day workin` on my Pinto is better than a good day at work!

78squirewagon

I am still for having it in Milwaukee the first weekend in May at the famed Milwaukee Mile Speedway. I will know for sure in about a month or so if the date is confirmed and if it is, we can share the track with about 500 other hot rods and customs. Of course we as a group would have special parking and go out on the track to do laps first. I would also make sure the local media got involved and a couple of the members might be asked to go on the radio the Friday before.
As far as the Friday and Saturday leading up to the show on Sunday, there is a lot to do in the area with a cruise night happening almost every day. I have talked with a couple of the Ford clubs and they are more than willing to host a night for us. I am sure that I could get a dealership to host a small show on Saturday.
Just let me know what you all think and i will pass it along to the folks at the Milwaukee Mile.
1978 Squire wagon,red, 69000 and counting original miles

1978 Hatchback, red (built four days after  the Squire)

78pinto

If the plans are made early and i have something to tow with, i'll try to attend wherever it may be. My wife works at a large hotel chain and the most any hotels will cost me is $69 a night and half off in hotel restaurants!  My new motor and turbo setup will be done and in the car for the next meet for sure.
** Jeff (78Pinto) is Missing from us but will always be a part of our community- We miss you Jeff **

68cyclone

YES IT WOULD BE NICE TO HAVE A "PINTO" MEET IN YOUR OWN BACK YARD: BUT THIS IS SIMPLY NOT POSSIBLE FOR US ALL.

THIS NEEDS TO BE DECIDED WITH ALL MEMBERS IN MIND,  NOT ON THE BASIS OF PERSONAL INTEREST.

I WILL SUPPORT A GROUP DECISION AND TRY TO ATTEND WHEREEVER THE GROUP DECIDES TO HOLD TH 3RD ANNUAL EVENT.

A WESTERN MEET WOULD BE NICE.  BUT CA. WOULD BE A STREACH FOR MOST EAST OF THE MISSISSIPPI.

I LIKE THE IDEA OF SACTIONED REGIONAL EVENTS-EAST,MIDWEST,WEST; IN ADDITION TO AN ANNUAL NATIONAL EVENT.

THANKS FOR THE OPPORTUNITY TO VOICE MY THOUGHTS.

68CYCLONE

phils toys

Dave ,
yes that is the place i am talking about, i did not know the details of the show . only that you had mentioned  going theree. I was ther about 10 yrs ago but only for about half of a day, visiting the village, did not make it to the museum. i would like to get back there sometime.
phil
2006, 07,08 ,10 Carlisle 3rd stock pinto 4 years same place
2007 PCCA East Regional Best Wagon
2008 CAHS Prom Coolest Ride
2011,2014 pinto stampede

Original74

Hey Brad,

Nice to see you post here. And you are right...Tulsa is in NO way western US! Unless something major changes, I will be in Anaheim next April. I think I will follow Pintony out......or tow him in! LOL Just kidding Tony.

Dave
Dave Herbeck- Missing from us... He will always be with us

1974 Sedan, 'Geraldine', 45,000 miles, orange and white, show car.
1976 Runabout, project.
1979 Sedan, 'Jade', 429 miles, show car, really needs to be in a museum. I am building him one!
1979 Runabout, light blue, 39,000 miles, daily driver

Original74

Hey Phil,

Are you talking about Greenfield Village in Dearborn? The place Henry Ford built?
I went there by special invite in June 2005. Their show is called Motor Musters. There are about 600 cars. They only allowed 1933-1973 cars and they opened up the 2005 show to 4 invites, a 74, me, a 75 and a 76. Only myself and a 1976 Pacer showed up as feature cars, but it was a blast. They have been running that show for 20 years and I was the first Pinto they had ever seen.
They opened the 2006 show up to 1933-1976. They do not want modified cars, probably not too popular on this board. But for those that are proud of our original unrestored cars, it's the place to be! It was the same time as Carlisle was. I will definitely make it there again. Motor Musters is always like the first week of June. Well worth the history and fun to go to.


Dave
Dave Herbeck- Missing from us... He will always be with us

1974 Sedan, 'Geraldine', 45,000 miles, orange and white, show car.
1976 Runabout, project.
1979 Sedan, 'Jade', 429 miles, show car, really needs to be in a museum. I am building him one!
1979 Runabout, light blue, 39,000 miles, daily driver

crazyhorse

I'll watch this thread for a week & note the various locations that are suggested. At the end of the week I'll post up a preliminary poll. As for a western meet, budgetary concerns tell me I likely won't be able to attend (read that as I'm too blamed broke to come)

Like last time I'll pitch in with organization, & I'll do anything in my power to help.

Look for a poll next Monday. This in NO way will produce final answers, rather get a feel for when, where the bulk of the members will be willing to meet.
How to tell when a redneck's time is up: He combines these two sentences... Hey man, hold my beer. Hey y'all watch this!
'74 Runabout, stock 2300,auto  RIP Darlin.
'95 Olds Gutless "POS"
'97 Subaru Legacy wagon "Kat"

hoots

It would be nice to have a meet somewhere in the heartland of the country. I'm sure I could find a place to meet here in Sioux Falls. This is a very welcoming city for car events. The local Ford dealer sponsors an all Ford show in June also.

There is a large car meet in Deadwood, SD at the end of August also, cars come from all over the country for that meet, it's called Kool Deadwood Nights.

turbopinto72

So, you consider Tulsa OK. as being Western? Not Me.
Brad F
1972, 2.5 Turbo Pinto
1972, Pangra
1973, Pangra
1971, 289 Pinto

Scott Hamilton

Branson, Missouri...

Weight (voting weight) should be skewed toward previous years attendees with more going to 'long haulers' example might be that Harley would have more 'weight' than myself because he attended both first and second since I was unable to make it to the PA meet. (Also because Harley can get Hooter Girls to do things I can't get them to do...)

I donno...

Thought?  Course, this might not allow newbies to vote objectively for a meet near them...

Just a thought....
Yellow 72, Runabout, 2000cc, 4Spd
Green 72, Runabout, 2000cc, 4Spd
White 73, Runabout, 2000cc, 4Spd
The Lemon, the Lime and the Coconut, :)

freepinto80

I think that it should be held somewhere near St. Louis, Missouri.

phils toys

Having read the previous post about  the official  meet it seams that a mid west was the general concise ,Tulsa or branson were suggested most. I probably would not be able to make it that far but  as you said not everyone  can make it to all of them.
also  i gathered that a ford sanctioned event would be a better  show  to attend, as people will just be happy to see ford's no matter of there condition.
at some point i would like to see it a dearborn , mi . greenwitch park(  hope i spelled that right)   i went there for vacation one year very nice place to visit.
2006, 07,08 ,10 Carlisle 3rd stock pinto 4 years same place
2007 PCCA East Regional Best Wagon
2008 CAHS Prom Coolest Ride
2011,2014 pinto stampede

pintoman

I agree with Original74.I think that we need to pick a spot somewhere west of Indiana for next years meet.I will be there if at all possible.I think it should be somewhere in the middle of this fine country of ours.How about Tulsa,Ok.
05 Pigon Forge Meet, 06 Carlile Meet Coordinator 06-07 Carlile Regional, Brief Case Award (ask)

Original74

I think it is time for us to begin planning for our third annual meet.

I would like to see replies to this post with suggested locations, then we could hone the list down with a poll and final vote. How does that sound?

I know we have 'pockets' of Pinto enthusiasts in certain regions of the US. Our first meet was in the central US, a bit east (Pigeon Forge, TN). Our secind meet was in the northeast (Carlisle, PA). Maybe it is time for a western meet. I know there are quite a few Pinto's in CA, based on the numbers in attendance at Anaheim in April.

I hope you join me in this thought as we plan where to hold our meets....whereas you might not be able to make it to every annual meet, you can plan to attend one closest to you when you can. Absolutely feel free to participate in a local club and attend as many shows as you can as a group representing FordPinto.com. I like the idea of an annual FordPinto.com sanctioned/sponsored event, but feel free to do as you please in regions where you can not travel every year. If I could get even one more Pinto to join me in Tulsa, I would be proud to hang a FordPinto.com PCCA flag!

Travel costs are certainly posing a challenge to traveling very far. Some of you drive your cars many thousands of miles to a show, some trailer their cars, some don't make it  ;). Bottom line, cost is a huge factor in determining where we can travel to for an annual meet.

As for myself, I have made a commitment to attend as many annual events as I can, as well as several local and regional shows annually. I hope to be able to do this for many years to come. In a few short years I have personally met quite a few of you on here and we as a club of Pinto enthusiasts are what make this an awesome hobby.

Please take a moment to look at our member map, remember where we have been, check out concentrations of Pinto owners and let's come up with a viable location for next year, OK?

Many thanks in advance,

Dave Herbeck
Original74
Tulsa, OK

Dave Herbeck- Missing from us... He will always be with us

1974 Sedan, 'Geraldine', 45,000 miles, orange and white, show car.
1976 Runabout, project.
1979 Sedan, 'Jade', 429 miles, show car, really needs to be in a museum. I am building him one!
1979 Runabout, light blue, 39,000 miles, daily driver