Mini Classifieds

1975 Pinto wagon emissions decal wanted
Date: 09/20/2018 11:01 pm
1972 Rallye wagon rebuild
Date: 11/14/2020 07:31 pm
1977 Pinto Hatchback Parts

Date: 08/29/2020 05:31 pm
1974 Ford Pinto Squire Wagon

Date: 05/30/2020 01:51 pm
74 pinto
Date: 09/11/2016 06:32 pm
Need Mustang II Manual Transmission Mount
Date: 04/21/2017 02:03 pm
Mallory Unilight dist 2.0
Date: 10/25/2019 03:44 pm
4:11 gears for 6.75 Make offer...NEED GONE

Date: 08/01/2018 01:27 pm
Pangra wanted
Date: 02/05/2017 01:58 pm

Why the Ford Pinto didn’t suck

Why the Ford Pinto didn't suckThe Ford Pinto was born a low-rent, stumpy thing in Dearborn 40 years ago and grew to become one of the most infamous cars in history. The thing is that it didn't actually suck. Really.

Even after four decades, what's the first thing that comes to mind when most people think of the Ford Pinto? Ka-BLAM! The truth is the Pinto was more than that — and this is the story of how the exploding Pinto became a pre-apocalyptic narrative, how the myth was exposed, and why you should race one.

The Pinto was CEO Lee Iacocca's baby, a homegrown answer to the threat of compact-sized economy cars from Japan and Germany, the sales of which had grown significantly throughout the 1960s. Iacocca demanded the Pinto cost under $2,000, and weigh under 2,000 pounds. It was an all-hands-on-deck project, and Ford got it done in 25 months from concept to production.

Building its own small car meant Ford's buyers wouldn't have to hew to the Japanese government's size-tamping regulations; Ford would have the freedom to choose its own exterior dimensions and engine sizes based on market needs (as did Chevy with the Vega and AMC with the Gremlin). And people cold dug it.

When it was unveiled in late 1970 (ominously on September 11), US buyers noted the Pinto's pleasant shape — bringing to mind a certain tailless amphibian — and interior layout hinting at a hipster's sunken living room. Some call it one of the ugliest cars ever made, but like fans of Mischa Barton, Pinto lovers care not what others think. With its strong Kent OHV four (a distant cousin of the Lotus TwinCam), the Pinto could at least keep up with its peers, despite its drum brakes and as long as one looked past its Russian-roulette build quality.

But what of the elephant in the Pinto's room? Yes, the whole blowing-up-on-rear-end-impact thing. It all started a little more than a year after the Pinto's arrival.

 

Grimshaw v. Ford Motor Company

On May 28, 1972, Mrs. Lilly Gray and 13-year-old passenger Richard Grimshaw, set out from Anaheim, California toward Barstow in Gray's six-month-old Ford Pinto. Gray had been having trouble with the car since new, returning it to the dealer several times for stalling. After stopping in San Bernardino for gasoline, Gray got back on I-15 and accelerated to around 65 mph. Approaching traffic congestion, she moved from the left lane to the middle lane, where the car suddenly stalled and came to a stop. A 1962 Ford Galaxie, the driver unable to stop or swerve in time, rear-ended the Pinto. The Pinto's gas tank was driven forward, and punctured on the bolts of the differential housing.

As the rear wheel well sections separated from the floor pan, a full tank of fuel sprayed straight into the passenger compartment, which was engulfed in flames. Gray later died from congestive heart failure, a direct result of being nearly incinerated, while Grimshaw was burned severely and left permanently disfigured. Grimshaw and the Gray family sued Ford Motor Company (among others), and after a six-month jury trial, verdicts were returned against Ford Motor Company. Ford did not contest amount of compensatory damages awarded to Grimshaw and the Gray family, and a jury awarded the plaintiffs $125 million, which the judge in the case subsequently reduced to the low seven figures. Other crashes and other lawsuits followed.

Why the Ford Pinto didn't suck

Mother Jones and Pinto Madness

In 1977, Mark Dowie, business manager of Mother Jones magazine published an article on the Pinto's "exploding gas tanks." It's the same article in which we first heard the chilling phrase, "How much does Ford think your life is worth?" Dowie had spent days sorting through filing cabinets at the Department of Transportation, examining paperwork Ford had produced as part of a lobbying effort to defeat a federal rear-end collision standard. That's where Dowie uncovered an innocuous-looking memo entitled "Fatalities Associated with Crash-Induced Fuel Leakage and Fires."

The Car Talk blog describes why the memo proved so damning.

In it, Ford's director of auto safety estimated that equipping the Pinto with [an] $11 part would prevent 180 burn deaths, 180 serious burn injuries and 2,100 burned cars, for a total cost of $137 million. Paying out $200,000 per death, $67,000 per injury and $700 per vehicle would cost only $49.15 million.

The government would, in 1978, demand Ford recall the million or so Pintos on the road to deal with the potential for gas-tank punctures. That "smoking gun" memo would become a symbol for corporate callousness and indifference to human life, haunting Ford (and other automakers) for decades. But despite the memo's cold calculations, was Ford characterized fairly as the Kevorkian of automakers?

Perhaps not. In 1991, A Rutgers Law Journal report [PDF] showed the total number of Pinto fires, out of 2 million cars and 10 years of production, stalled at 27. It was no more than any other vehicle, averaged out, and certainly not the thousand or more suggested by Mother Jones.

Why the Ford Pinto didn't suck

The big rebuttal, and vindication?

But what of the so-called "smoking gun" memo Dowie had unearthed? Surely Ford, and Lee Iacocca himself, were part of a ruthless establishment who didn't care if its customers lived or died, right? Well, not really. Remember that the memo was a lobbying document whose audience was intended to be the NHTSA. The memo didn't refer to Pintos, or even Ford products, specifically, but American cars in general. It also considered rollovers not rear-end collisions. And that chilling assignment of value to a human life? Indeed, it was federal regulators who often considered that startling concept in their own deliberations. The value figure used in Ford's memo was the same one regulators had themselves set forth.

In fact, measured by occupant fatalities per million cars in use during 1975 and 1976, the Pinto's safety record compared favorably to other subcompacts like the AMC Gremlin, Chevy Vega, Toyota Corolla and VW Beetle.

And what of Mother Jones' Dowie? As the Car Talk blog points out, Dowie now calls the Pinto, "a fabulous vehicle that got great gas mileage," if not for that one flaw: The legendary "$11 part."

Why the Ford Pinto didn't suck

Pinto Racing Doesn't Suck

Back in 1974, Car and Driver magazine created a Pinto for racing, an exercise to prove brains and common sense were more important than an unlimited budget and superstar power. As Patrick Bedard wrote in the March, 1975 issue of Car and Driver, "It's a great car to drive, this Pinto," referring to the racer the magazine prepared for the Goodrich Radial Challenge, an IMSA-sanctioned road racing series for small sedans.

Why'd they pick a Pinto over, say, a BMW 2002 or AMC Gremlin? Current owner of the prepped Pinto, Fox Motorsports says it was a matter of comparing the car's frontal area, weight, piston displacement, handling, wheel width, and horsepower to other cars of the day that would meet the entry criteria. (Racers like Jerry Walsh had by then already been fielding Pintos in IMSA's "Baby Grand" class.)

Bedard, along with Ron Nash and company procured a 30,000-mile 1972 Pinto two-door to transform. In addition to safety, chassis and differential mods, the team traded a 200-pound IMSA weight penalty for the power gain of Ford's 2.3-liter engine, which Bedard said "tipped the scales" in the Pinto's favor. But according to Bedard, it sounds like the real advantage was in the turns, thanks to some add-ons from Mssrs. Koni and Bilstein.

"The Pinto's advantage was cornering ability," Bedard wrote. "I don't think there was another car in the B. F. Goodrich series that was quicker through the turns on a dry track. The steering is light and quick, and the suspension is direct and predictable in a way that street cars never can be. It never darts over bumps, the axle is perfectly controlled and the suspension doesn't bottom."

Need more proof of the Pinto's lack of suck? Check out the SCCA Washington, DC region's spec-Pinto series.

Members
  • Total Members: 7,896
  • Latest: tdok
Stats
  • Total Posts: 139,582
  • Total Topics: 16,269
  • Online today: 1,521
  • Online ever: 2,670 (May 09, 2025, 01:57:20 AM)
Users Online
  • Users: 0
  • Guests: 1495
  • Total: 1495
F&I...more

My Somewhat Begrudging Apology To Ford Pinto

ford-pinto.jpg

I never thought I’d offer an apology to the Ford Pinto, but I guess I owe it one.

I had a Pinto in the 1970s. Actually, my wife bought it a few months before we got married. The car became sort of a wedding dowry. So did the remaining 80% of the outstanding auto loan.

During a relatively brief ownership, the Pinto’s repair costs exceeded the original price of the car. It wasn’t a question of if it would fail, but when. And where. Sometimes, it simply wouldn’t start in the driveway. Other times, it would conk out at a busy intersection.

It ranks as the worst car I ever had. That was back when some auto makers made quality something like Job 100, certainly not Job 1.

Despite my bad Pinto experience, I suppose an apology is in order because of a recent blog I wrote. It centered on Toyota’s sudden-acceleration problems. But in discussing those, I invoked the memory of exploding Pintos, perpetuating an inaccuracy.

The widespread allegation was that, due to a design flaw, Pinto fuel tanks could readily blow up in rear-end collisions, setting the car and its occupants afire.

People started calling the Pinto “the barbecue that seats four.” And the lawsuits spread like wild fire.

Responding to my blog, a Ford (“I would very much prefer to keep my name out of print”) manager contacted me to set the record straight.

He says exploding Pintos were a myth that an investigation debunked nearly 20 years ago. He cites Gary Schwartz’ 1991 Rutgers Law Review paper that cut through the wild claims and examined what really happened.

Schwartz methodically determined the actual number of Pinto rear-end explosion deaths was not in the thousands, as commonly thought, but 27.

In 1975-76, the Pinto averaged 310 fatalities a year. But the similar-size Toyota Corolla averaged 313, the VW Beetle 374 and the Datsun 1200/210 came in at 405.

Yes, there were cases such as a Pinto exploding while parked on the shoulder of the road and hit from behind by a speeding pickup truck. But fiery rear-end collisions comprised only 0.6% of all fatalities back then, and the Pinto had a lower death rate in that category than the average compact or subcompact, Schwartz said after crunching the numbers. Nor was there anything about the Pinto’s rear-end design that made it particularly unsafe.

Not content to portray the Pinto as an incendiary device, ABC’s 20/20 decided to really heat things up in a 1978 broadcast containing “startling new developments.” ABC breathlessly reported that, not just Pintos, but fullsize Fords could blow up if hit from behind.

20/20 thereupon aired a video, shot by UCLA researchers, showing a Ford sedan getting rear-ended and bursting into flames. A couple of problems with that video:

One, it was shot 10 years earlier.

Two, the UCLA researchers had openly said in a published report that they intentionally rigged the vehicle with an explosive.

That’s because the test was to determine how a crash fire affected the car’s interior, not to show how easily Fords became fire balls. They said they had to use an accelerant because crash blazes on their own are so rare. They had tried to induce a vehicle fire in a crash without using an igniter, but failed.

ABC failed to mention any of that when correspondent Sylvia Chase reported on “Ford’s secret rear-end crash tests.”

We could forgive ABC for that botched reporting job. After all, it was 32 years ago. But a few weeks ago, ABC, in another one of its rigged auto exposes, showed video of a Toyota apparently accelerating on its own.

Turns out, the “runaway” vehicle had help from an associate professor. He built a gizmo with an on-off switch to provide acceleration on demand. Well, at least ABC didn’t show the Toyota slamming into a wall and bursting into flames.

In my blog, I also mentioned that Ford’s woes got worse in the 1970s with the supposed uncovering of an internal memo by a Ford attorney who allegedly calculated it would cost less to pay off wrongful-death suits than to redesign the Pinto.

It became known as the “Ford Pinto memo,” a smoking gun. But Schwartz looked into that, too. He reported the memo did not pertain to Pintos or any Ford products. Instead, it had to do with American vehicles in general.

It dealt with rollovers, not rear-end crashes. It did not address tort liability at all, let alone advocate it as a cheaper alternative to a redesign. It put a value to human life because federal regulators themselves did so.

The memo was meant for regulators’ eyes only. But it was off to the races after Mother Jones magazine got a hold of a copy and reported what wasn’t the case.

The exploding-Pinto myth lives on, largely because more Americans watch 20/20 than read the Rutgers Law Review. One wonders what people will recollect in 2040 about Toyota’s sudden accelerations, which more and more look like driver error and, in some cases, driver shams.

So I guess I owe the Pinto an apology. But it’s half-hearted, because my Pinto gave me much grief, even though, as the Ford manager notes, “it was a cheap car, built long ago and lots of things have changed, almost all for the better.”

Here goes: If I said anything that offended you, Pinto, I’m sorry. And thanks for not blowing up on me.

Electronic ignition conversion

Started by ponyboy, April 11, 2019, 10:09:22 PM

Previous topic - Next topic

0 Members and 1 Guest are viewing this topic.

71pintoracer

This is an older post and no updates but l have a Mallory Unilight for a 2.0 for sale. Lots of other 2.0 performance parts as well
If you don't have time to do it right, when will you have time to do it over?

Henrius

Quote from: ponyboy on April 11, 2019, 10:09:22 PM
Will this fit a 1973 Pinto 2.0L OHC? Or is there something better? For some reason I am having to regap my points every couple of weeks. I've been just driving down the road when it starts misfiring, and I have to pull over and regap the points. The gap always widens. The retainer screw seems tight enough and the points are new. https://www.summitracing.com/parts/pnx-91847v/applications/make/ford

Long ago I put a Mallory Unilite distirubutor on my 2.0 and never looked back. Don't know if it is still available.

Later I plugged up an MSD unit. Runs like a champ.
1973 Pinto Runabout with upgraded 2.0 liter & 4 speed, and factory sunroof. My first car, now restored, and better than it was when it rolled off the assembly line!

LongTimeFordMan

Well i think they have changed a lot since 1995.  There is now a series 1 and a series 2.

I started with a series 1 in 2014 and updated in 2017 have had no problems..

The distributors in early 71-73 cars were bosch , same as volkswagons with d8fferent drives.

But its important to rework the advance curve. The factory distributors had major tech for emission control and it is impossible to use enough i itial timing for low.end torque without having the total.go to 38 degrees which id way too much. 2.0 likes 28-30 total.and 14 at 1000 rpm.

I experimented about a year to find the optimum curve.. check my posts on how to mod.

My first experience with electronic conversions was with a 68 mgb and i used an early allison optical trigger one. 

Ran it for 10 years with no problems.

I.keep a set of points and condenser for emergencies. And also.set up a spare distributor with my first series 1 pertronics when i do the stampedes usually 3000 miles or more but havent had any problems.
Red 1973 pinto wagon DD, SoCal desert car, Factory 4 speed, 3.40 gears, Stock engine, 14" rims and tires, 60 K original miles

TIGGER

My buddy put a pertronix unit in his 2.0 Pinto back in like 1993.  The same time I put one in my 67 coupe.  We bought them at the same time using our bonus LOL.  He never had an issue with it for the rest of the time he owned it and till this day I have never had an issue with mine.
79 4cyl Wagon
73 Turbo HB
78 Cruising Wagon (sold 8/6/11)

LongTimeFordMan

Hi..

I had a new 72 pinto in 72 when they were new.. had same probl3m with pinits.. the problem is that the condenser fails. I resorted to using aftermarket .22 mf capatrs and carried several.

I now have a 72 that Ive had 4 years and the first thing i did when i gotitwas to insrall a.pertronix series 1. 

It ran reliably for 2 years until i arbitarily d4ecided to upgrade to the series 2.

No problems with series1 but just decded to upgrade.

Runs flawlessly and would recommend the conversion.

In addition to reliability the pertronix also provides more precse timing.

I also modded the factory distributor to limit the total centrifugal advance to about 14 degrees by replacing the high speed spring with a wire loop, locked down the rotating plate that holds the points and provides the ground and removed the vacuum advance.

Setinitial timing to about 14 degrees at 1000 rpm so total advance is 28.

Ign plus distributor mods added a lot to performanc.

Also consider installing an adjustable STEEL not aluminum cam pulley from Racer Walsh and advancing cam timing about 4-6 degrees

I postd pix of the distributor mods in a thread about 5 speed transmissions here..
Red 1973 pinto wagon DD, SoCal desert car, Factory 4 speed, 3.40 gears, Stock engine, 14" rims and tires, 60 K original miles

ponyboy

Thanks, I'll get one from Rockauto. I'm getting tired of having ignition problems with this car. It runs great otherwise. First I had a problem where it would start right up, then start misfiring after a couple of miles. I traced that to the condenser. So I replaced the condenser, points, rotor, and cap. The book says to set the points to .025. But it didn't run so good that way, so I set them at .022. It ran perfect. For a couple of weeks. Then this problem started. I like points, because I don't like electronics. But I also want a car that will run reliably. I mostly drive old cars because they don't have electronics and emissions crap on them.

The Whistler

Either the one  from Summit or Rock Auto will work. I have installed those in the past when they were less reliable but  was lucky! We had good results.
Turbo is a way of life

one2.34me


ponyboy, I'm not very knowledgeable on ignition stuff. I use rockauto a lot and I've never had a problem with the parts they sell. They offer the two electronic ignitions below for a 1973 Pinto 2.0 OHC.
https://www.rockauto.com/en/catalog/ford,1973,pinto,2.0l+122cid+l4,1135134,ignition,ignition+conversion+kit,11340

Wittsend

I could be wrong but I'm guessing when they state, 2.0L/122 they are referring to the 2.0 version of the Lima engine which is more commonly knows as the (1974 and up) 2.3. So, my guess would be "No."

In these older cars there are only a few aspects to the ignition. The points, condenser, coil and its resistor. Unless there is something odd about the 2.0 points lobes (that might cause more sparking) then it comes down to material of the points and/or the coil and its resistor.  You say the gap widens so it is likely the point burning way. If it was the rubbing block that was wearing, the gap would tighten.  I'd assume the issues is either poor contact material, a contact area too small to handle the load or the resistor/coil combination is too high of a load.

Make sure you distributor has no wobble otherwise your gap can be all over the place.  I'd think if the coil/resistor are the problem that anything aftermarket can replace them. Just remember the resistor has to match the ohms rating the coil calls for.  You might want to look at Burton or any other performance aftermarket company to see what they offer.   Electronic ignitions can be pretty simple using items like the old Chrysler ignition box and magnetic sensor. But it would require tools like a lathe to convert the reluctor to fit where the lobes are now. And, the 2.0 distributor case is pretty small..., so it might not fit at all.

You might contact Pertronix and see if they make a kit for the early Pinto 2.0. Just don't get the Ignitor I as there is an issue where it burns up if the ignition is left on but the motor isn't running. Hopefully those who have a 2.0 can give more information.

JoeBob

Back in 72 my new pinto burnt points. Ford could not fix it. I kept half a dozen in the glove box and changed them out often on the side of the road.
77 yellow Bobcat hatchback
Deuteronomy 7:9

ponyboy

Will this fit a 1973 Pinto 2.0L OHC? Or is there something better? For some reason I am having to regap my points every couple of weeks. I've been just driving down the road when it starts misfiring, and I have to pull over and regap the points. The gap always widens. The retainer screw seems tight enough and the points are new. https://www.summitracing.com/parts/pnx-91847v/applications/make/ford