Mini Classifieds

4 speed pinto transmission

Date: 05/13/2021 05:29 pm
Chilton's Repair & Tune-up Guide 1971-1979 Pinto and Bobcat

Date: 03/06/2017 01:24 am
72 Runabout Sprint Edition

Date: 04/25/2018 02:51 pm
Pinto interior parts for Cruisen / Rallye wagon
Date: 01/19/2021 03:56 pm
Drivers side door panel Orange
Date: 05/22/2018 01:54 pm
1977 pinto rear bumper
Date: 04/19/2021 11:57 am
EARLY PINTO CLUTCH PEDAL ASSEMBLY
Date: 02/14/2019 06:27 pm
Need 77 or 78 Cruising Wagon Speedometer Tachometer Assembly
Date: 06/24/2020 06:12 am
Mirror
Date: 04/15/2020 01:42 pm

Why the Ford Pinto didn’t suck

Why the Ford Pinto didn't suckThe Ford Pinto was born a low-rent, stumpy thing in Dearborn 40 years ago and grew to become one of the most infamous cars in history. The thing is that it didn't actually suck. Really.

Even after four decades, what's the first thing that comes to mind when most people think of the Ford Pinto? Ka-BLAM! The truth is the Pinto was more than that — and this is the story of how the exploding Pinto became a pre-apocalyptic narrative, how the myth was exposed, and why you should race one.

The Pinto was CEO Lee Iacocca's baby, a homegrown answer to the threat of compact-sized economy cars from Japan and Germany, the sales of which had grown significantly throughout the 1960s. Iacocca demanded the Pinto cost under $2,000, and weigh under 2,000 pounds. It was an all-hands-on-deck project, and Ford got it done in 25 months from concept to production.

Building its own small car meant Ford's buyers wouldn't have to hew to the Japanese government's size-tamping regulations; Ford would have the freedom to choose its own exterior dimensions and engine sizes based on market needs (as did Chevy with the Vega and AMC with the Gremlin). And people cold dug it.

When it was unveiled in late 1970 (ominously on September 11), US buyers noted the Pinto's pleasant shape — bringing to mind a certain tailless amphibian — and interior layout hinting at a hipster's sunken living room. Some call it one of the ugliest cars ever made, but like fans of Mischa Barton, Pinto lovers care not what others think. With its strong Kent OHV four (a distant cousin of the Lotus TwinCam), the Pinto could at least keep up with its peers, despite its drum brakes and as long as one looked past its Russian-roulette build quality.

But what of the elephant in the Pinto's room? Yes, the whole blowing-up-on-rear-end-impact thing. It all started a little more than a year after the Pinto's arrival.

 

Grimshaw v. Ford Motor Company

On May 28, 1972, Mrs. Lilly Gray and 13-year-old passenger Richard Grimshaw, set out from Anaheim, California toward Barstow in Gray's six-month-old Ford Pinto. Gray had been having trouble with the car since new, returning it to the dealer several times for stalling. After stopping in San Bernardino for gasoline, Gray got back on I-15 and accelerated to around 65 mph. Approaching traffic congestion, she moved from the left lane to the middle lane, where the car suddenly stalled and came to a stop. A 1962 Ford Galaxie, the driver unable to stop or swerve in time, rear-ended the Pinto. The Pinto's gas tank was driven forward, and punctured on the bolts of the differential housing.

As the rear wheel well sections separated from the floor pan, a full tank of fuel sprayed straight into the passenger compartment, which was engulfed in flames. Gray later died from congestive heart failure, a direct result of being nearly incinerated, while Grimshaw was burned severely and left permanently disfigured. Grimshaw and the Gray family sued Ford Motor Company (among others), and after a six-month jury trial, verdicts were returned against Ford Motor Company. Ford did not contest amount of compensatory damages awarded to Grimshaw and the Gray family, and a jury awarded the plaintiffs $125 million, which the judge in the case subsequently reduced to the low seven figures. Other crashes and other lawsuits followed.

Why the Ford Pinto didn't suck

Mother Jones and Pinto Madness

In 1977, Mark Dowie, business manager of Mother Jones magazine published an article on the Pinto's "exploding gas tanks." It's the same article in which we first heard the chilling phrase, "How much does Ford think your life is worth?" Dowie had spent days sorting through filing cabinets at the Department of Transportation, examining paperwork Ford had produced as part of a lobbying effort to defeat a federal rear-end collision standard. That's where Dowie uncovered an innocuous-looking memo entitled "Fatalities Associated with Crash-Induced Fuel Leakage and Fires."

The Car Talk blog describes why the memo proved so damning.

In it, Ford's director of auto safety estimated that equipping the Pinto with [an] $11 part would prevent 180 burn deaths, 180 serious burn injuries and 2,100 burned cars, for a total cost of $137 million. Paying out $200,000 per death, $67,000 per injury and $700 per vehicle would cost only $49.15 million.

The government would, in 1978, demand Ford recall the million or so Pintos on the road to deal with the potential for gas-tank punctures. That "smoking gun" memo would become a symbol for corporate callousness and indifference to human life, haunting Ford (and other automakers) for decades. But despite the memo's cold calculations, was Ford characterized fairly as the Kevorkian of automakers?

Perhaps not. In 1991, A Rutgers Law Journal report [PDF] showed the total number of Pinto fires, out of 2 million cars and 10 years of production, stalled at 27. It was no more than any other vehicle, averaged out, and certainly not the thousand or more suggested by Mother Jones.

Why the Ford Pinto didn't suck

The big rebuttal, and vindication?

But what of the so-called "smoking gun" memo Dowie had unearthed? Surely Ford, and Lee Iacocca himself, were part of a ruthless establishment who didn't care if its customers lived or died, right? Well, not really. Remember that the memo was a lobbying document whose audience was intended to be the NHTSA. The memo didn't refer to Pintos, or even Ford products, specifically, but American cars in general. It also considered rollovers not rear-end collisions. And that chilling assignment of value to a human life? Indeed, it was federal regulators who often considered that startling concept in their own deliberations. The value figure used in Ford's memo was the same one regulators had themselves set forth.

In fact, measured by occupant fatalities per million cars in use during 1975 and 1976, the Pinto's safety record compared favorably to other subcompacts like the AMC Gremlin, Chevy Vega, Toyota Corolla and VW Beetle.

And what of Mother Jones' Dowie? As the Car Talk blog points out, Dowie now calls the Pinto, "a fabulous vehicle that got great gas mileage," if not for that one flaw: The legendary "$11 part."

Why the Ford Pinto didn't suck

Pinto Racing Doesn't Suck

Back in 1974, Car and Driver magazine created a Pinto for racing, an exercise to prove brains and common sense were more important than an unlimited budget and superstar power. As Patrick Bedard wrote in the March, 1975 issue of Car and Driver, "It's a great car to drive, this Pinto," referring to the racer the magazine prepared for the Goodrich Radial Challenge, an IMSA-sanctioned road racing series for small sedans.

Why'd they pick a Pinto over, say, a BMW 2002 or AMC Gremlin? Current owner of the prepped Pinto, Fox Motorsports says it was a matter of comparing the car's frontal area, weight, piston displacement, handling, wheel width, and horsepower to other cars of the day that would meet the entry criteria. (Racers like Jerry Walsh had by then already been fielding Pintos in IMSA's "Baby Grand" class.)

Bedard, along with Ron Nash and company procured a 30,000-mile 1972 Pinto two-door to transform. In addition to safety, chassis and differential mods, the team traded a 200-pound IMSA weight penalty for the power gain of Ford's 2.3-liter engine, which Bedard said "tipped the scales" in the Pinto's favor. But according to Bedard, it sounds like the real advantage was in the turns, thanks to some add-ons from Mssrs. Koni and Bilstein.

"The Pinto's advantage was cornering ability," Bedard wrote. "I don't think there was another car in the B. F. Goodrich series that was quicker through the turns on a dry track. The steering is light and quick, and the suspension is direct and predictable in a way that street cars never can be. It never darts over bumps, the axle is perfectly controlled and the suspension doesn't bottom."

Need more proof of the Pinto's lack of suck? Check out the SCCA Washington, DC region's spec-Pinto series.

Members
Stats
  • Total Posts: 139,575
  • Total Topics: 16,267
  • Online today: 1,292
  • Online ever: 2,670 (May 09, 2025, 01:57:20 AM)
Users Online
  • Users: 0
  • Guests: 553
  • Total: 553
F&I...more

My Somewhat Begrudging Apology To Ford Pinto

ford-pinto.jpg

I never thought I’d offer an apology to the Ford Pinto, but I guess I owe it one.

I had a Pinto in the 1970s. Actually, my wife bought it a few months before we got married. The car became sort of a wedding dowry. So did the remaining 80% of the outstanding auto loan.

During a relatively brief ownership, the Pinto’s repair costs exceeded the original price of the car. It wasn’t a question of if it would fail, but when. And where. Sometimes, it simply wouldn’t start in the driveway. Other times, it would conk out at a busy intersection.

It ranks as the worst car I ever had. That was back when some auto makers made quality something like Job 100, certainly not Job 1.

Despite my bad Pinto experience, I suppose an apology is in order because of a recent blog I wrote. It centered on Toyota’s sudden-acceleration problems. But in discussing those, I invoked the memory of exploding Pintos, perpetuating an inaccuracy.

The widespread allegation was that, due to a design flaw, Pinto fuel tanks could readily blow up in rear-end collisions, setting the car and its occupants afire.

People started calling the Pinto “the barbecue that seats four.” And the lawsuits spread like wild fire.

Responding to my blog, a Ford (“I would very much prefer to keep my name out of print”) manager contacted me to set the record straight.

He says exploding Pintos were a myth that an investigation debunked nearly 20 years ago. He cites Gary Schwartz’ 1991 Rutgers Law Review paper that cut through the wild claims and examined what really happened.

Schwartz methodically determined the actual number of Pinto rear-end explosion deaths was not in the thousands, as commonly thought, but 27.

In 1975-76, the Pinto averaged 310 fatalities a year. But the similar-size Toyota Corolla averaged 313, the VW Beetle 374 and the Datsun 1200/210 came in at 405.

Yes, there were cases such as a Pinto exploding while parked on the shoulder of the road and hit from behind by a speeding pickup truck. But fiery rear-end collisions comprised only 0.6% of all fatalities back then, and the Pinto had a lower death rate in that category than the average compact or subcompact, Schwartz said after crunching the numbers. Nor was there anything about the Pinto’s rear-end design that made it particularly unsafe.

Not content to portray the Pinto as an incendiary device, ABC’s 20/20 decided to really heat things up in a 1978 broadcast containing “startling new developments.” ABC breathlessly reported that, not just Pintos, but fullsize Fords could blow up if hit from behind.

20/20 thereupon aired a video, shot by UCLA researchers, showing a Ford sedan getting rear-ended and bursting into flames. A couple of problems with that video:

One, it was shot 10 years earlier.

Two, the UCLA researchers had openly said in a published report that they intentionally rigged the vehicle with an explosive.

That’s because the test was to determine how a crash fire affected the car’s interior, not to show how easily Fords became fire balls. They said they had to use an accelerant because crash blazes on their own are so rare. They had tried to induce a vehicle fire in a crash without using an igniter, but failed.

ABC failed to mention any of that when correspondent Sylvia Chase reported on “Ford’s secret rear-end crash tests.”

We could forgive ABC for that botched reporting job. After all, it was 32 years ago. But a few weeks ago, ABC, in another one of its rigged auto exposes, showed video of a Toyota apparently accelerating on its own.

Turns out, the “runaway” vehicle had help from an associate professor. He built a gizmo with an on-off switch to provide acceleration on demand. Well, at least ABC didn’t show the Toyota slamming into a wall and bursting into flames.

In my blog, I also mentioned that Ford’s woes got worse in the 1970s with the supposed uncovering of an internal memo by a Ford attorney who allegedly calculated it would cost less to pay off wrongful-death suits than to redesign the Pinto.

It became known as the “Ford Pinto memo,” a smoking gun. But Schwartz looked into that, too. He reported the memo did not pertain to Pintos or any Ford products. Instead, it had to do with American vehicles in general.

It dealt with rollovers, not rear-end crashes. It did not address tort liability at all, let alone advocate it as a cheaper alternative to a redesign. It put a value to human life because federal regulators themselves did so.

The memo was meant for regulators’ eyes only. But it was off to the races after Mother Jones magazine got a hold of a copy and reported what wasn’t the case.

The exploding-Pinto myth lives on, largely because more Americans watch 20/20 than read the Rutgers Law Review. One wonders what people will recollect in 2040 about Toyota’s sudden accelerations, which more and more look like driver error and, in some cases, driver shams.

So I guess I owe the Pinto an apology. But it’s half-hearted, because my Pinto gave me much grief, even though, as the Ford manager notes, “it was a cheap car, built long ago and lots of things have changed, almost all for the better.”

Here goes: If I said anything that offended you, Pinto, I’m sorry. And thanks for not blowing up on me.

Pinto engine on wood splitter.

Started by godtool, June 21, 2006, 07:02:33 PM

Previous topic - Next topic

0 Members and 1 Guest are viewing this topic.

Pintony

Tell the DA parts guy that you have a 1971-74 Pinto engine 2000cc 122 C.I.
BTW that is 1 ugly 2.0

godtool

Took head off engine, here are pics, think I can get parts to rebuild it?  Its a 1972, but I don't know what kind of auto it came out of.   All ther parts guys need an application.  When I say "wood splitter" and they don't know how to use engine casting #'s I'm at a dead end.  Here is a link to pics.

http://w65.photobucket.com/widgets/dynamicflash.php?featuretype=bucketshow&featurename=Woodsplitter_engine_pics&pa=/h213/godtool/Pinto%20Engine/
I had a 47 Willys Jeep with a 4 cyl. pinto, and then a v6 capri back in 1984-86 when I was 14-16.  Now I have a pinto engine on a wood splitter.

godtool

Thanks for all the info.   I'll try spinning the valves.   I appreciate all your feedback. :)
I had a 47 Willys Jeep with a 4 cyl. pinto, and then a v6 capri back in 1984-86 when I was 14-16.  Now I have a pinto engine on a wood splitter.

goodolboydws

Since this isn't exactly a high precision application, you might want to try doing this to improve the valve to seat seal before you invest a lot of time and effort in looking for something else or taking the cylinder head off for a valve job.  It's worked for me in the past on a few marginally rusty or carboned up valves and seats. If they are really bad, this won't work, but it's probably worth a try. It's a crude method for lapping valves WITHOUT using grinding compound. Sometimes it works, sometimes it doesn't.

By the way, I'm assuming here that you have already loosened up the valve stems by soaking them with some sort of penetrating oil so that they are not sticking in the valve guides, as this alone can cause a poor compression reading.

Take all the spark plugs out and turn the engine over by hand until you have TDC on cylinder # 1. (At this point some people shove the end of a length of rope in through the spark plug hole, jamming in enough so that the valves can't possibly fall down into the engine too far to grab from their stems.)

Once you have the valve spring retainer, keepers, and valve springs out of your way,  (you can leave the valve seals on for this) wrap the valve stem with something like a few turns of electrical tape to protect it and also to give you something to grab onto.

Now all you have to do is to spin the valve, alternating between forwards and backwards while holding it upwards, against the valve seat. Some people go for broke and use a battery powered or electric drill, but I'd try it by hand first, as that may be enough to knock off some high spots. 

After doing this for a while, try doing the leakdown test on that cylinder again. If it's now good, you may be lucky and be able to clean up the others the same way.

You may want to blow out the cylinder with compressed air before starting the engine.

BTW, I think that the 12pt. spline drive size you're looking for to use on the 2000cc engines' cylinder head is either 10 or 12mm, as those are the only 2 sizes that I have in one of my tool cabinets, and I'm fairly certain that I bought one of them for retorquing he cylinder head or replacing the timing belt on one of MY Pintos. (I've worked on other manufacturers' engines in the interim, but still haven't had to acquire a full set.)

You should be able to measure closely enough to tell which size is correct. The timing belt tensioner uses either the same size or the other size of the spline drive.

godtool

I have a homemade wood splitter.  I never saw it run.  It has a 1972 Ford 4 cylinder on it, #70HM6015B-A  2.0 122 CI.  Right now the engine does not run and it has no compression.  A leakdown test shows me the exhaust valves are the cause to zero compression.   I believe it was left outside so the valve seats are probably rusted.  I had the valve cover off and the valves seem to be opening fine.   The head is fastened down with "spleen" bolts.  Like a torx but many more points.  Anyone know what size they are so I can buy the right size bit.  My 2nd question is if the engine is financially beyond repair what other engines have the same bell housing bolt pattern?  The shaft that exits the bell housing is welded to the clutch pressure plate, so the pressure plate\crank bolt pattern is important but I guess I could cut the shaft if needed to fit a different crank.  Since the engine mounts into the wood splitter using the 4 holes on the small end of the bell housing and the engine mount holes on either side of the block, just re&re'ing another same engine would be nice and easy.  I've phoned the Ford autowreckers in Langley and Vancouver BC, Canada, but the guy in Langley said, its like trying to find a needle in a haystack.   The guy in Vancouver said bring the engine down and he can find something to match up.  I could always swap another brand of engine in but I would prefer to stick to the easier route of staying with the same engine.  Any help would be appreciated.  I can always post digital pics if it would help.
I had a 47 Willys Jeep with a 4 cyl. pinto, and then a v6 capri back in 1984-86 when I was 14-16.  Now I have a pinto engine on a wood splitter.