Mini Classifieds

1979 Pinto Rear Bumper
Date: 03/26/2021 03:26 pm
77-78 front grill
Date: 04/07/2017 12:35 am
1971 Pinto Parting out

Date: 07/06/2018 01:11 pm
2.8 radiator
Date: 10/25/2019 04:10 pm
1974 Ford Pinto

Date: 10/16/2017 10:45 am
1973 Pangra

Date: 01/06/2015 02:19 pm
Gas Tank Sending Unit
Date: 05/22/2018 02:17 pm
WANTED: Dash, fender, hood, gauge bezel '73 Wagon
Date: 01/18/2017 05:35 pm
1971 yellow Pinto hatchback with limited edition chrome strips on rear door, 1600 cc engine

Date: 02/26/2017 03:22 pm

Why the Ford Pinto didn’t suck

Why the Ford Pinto didn't suckThe Ford Pinto was born a low-rent, stumpy thing in Dearborn 40 years ago and grew to become one of the most infamous cars in history. The thing is that it didn't actually suck. Really.

Even after four decades, what's the first thing that comes to mind when most people think of the Ford Pinto? Ka-BLAM! The truth is the Pinto was more than that — and this is the story of how the exploding Pinto became a pre-apocalyptic narrative, how the myth was exposed, and why you should race one.

The Pinto was CEO Lee Iacocca's baby, a homegrown answer to the threat of compact-sized economy cars from Japan and Germany, the sales of which had grown significantly throughout the 1960s. Iacocca demanded the Pinto cost under $2,000, and weigh under 2,000 pounds. It was an all-hands-on-deck project, and Ford got it done in 25 months from concept to production.

Building its own small car meant Ford's buyers wouldn't have to hew to the Japanese government's size-tamping regulations; Ford would have the freedom to choose its own exterior dimensions and engine sizes based on market needs (as did Chevy with the Vega and AMC with the Gremlin). And people cold dug it.

When it was unveiled in late 1970 (ominously on September 11), US buyers noted the Pinto's pleasant shape — bringing to mind a certain tailless amphibian — and interior layout hinting at a hipster's sunken living room. Some call it one of the ugliest cars ever made, but like fans of Mischa Barton, Pinto lovers care not what others think. With its strong Kent OHV four (a distant cousin of the Lotus TwinCam), the Pinto could at least keep up with its peers, despite its drum brakes and as long as one looked past its Russian-roulette build quality.

But what of the elephant in the Pinto's room? Yes, the whole blowing-up-on-rear-end-impact thing. It all started a little more than a year after the Pinto's arrival.

 

Grimshaw v. Ford Motor Company

On May 28, 1972, Mrs. Lilly Gray and 13-year-old passenger Richard Grimshaw, set out from Anaheim, California toward Barstow in Gray's six-month-old Ford Pinto. Gray had been having trouble with the car since new, returning it to the dealer several times for stalling. After stopping in San Bernardino for gasoline, Gray got back on I-15 and accelerated to around 65 mph. Approaching traffic congestion, she moved from the left lane to the middle lane, where the car suddenly stalled and came to a stop. A 1962 Ford Galaxie, the driver unable to stop or swerve in time, rear-ended the Pinto. The Pinto's gas tank was driven forward, and punctured on the bolts of the differential housing.

As the rear wheel well sections separated from the floor pan, a full tank of fuel sprayed straight into the passenger compartment, which was engulfed in flames. Gray later died from congestive heart failure, a direct result of being nearly incinerated, while Grimshaw was burned severely and left permanently disfigured. Grimshaw and the Gray family sued Ford Motor Company (among others), and after a six-month jury trial, verdicts were returned against Ford Motor Company. Ford did not contest amount of compensatory damages awarded to Grimshaw and the Gray family, and a jury awarded the plaintiffs $125 million, which the judge in the case subsequently reduced to the low seven figures. Other crashes and other lawsuits followed.

Why the Ford Pinto didn't suck

Mother Jones and Pinto Madness

In 1977, Mark Dowie, business manager of Mother Jones magazine published an article on the Pinto's "exploding gas tanks." It's the same article in which we first heard the chilling phrase, "How much does Ford think your life is worth?" Dowie had spent days sorting through filing cabinets at the Department of Transportation, examining paperwork Ford had produced as part of a lobbying effort to defeat a federal rear-end collision standard. That's where Dowie uncovered an innocuous-looking memo entitled "Fatalities Associated with Crash-Induced Fuel Leakage and Fires."

The Car Talk blog describes why the memo proved so damning.

In it, Ford's director of auto safety estimated that equipping the Pinto with [an] $11 part would prevent 180 burn deaths, 180 serious burn injuries and 2,100 burned cars, for a total cost of $137 million. Paying out $200,000 per death, $67,000 per injury and $700 per vehicle would cost only $49.15 million.

The government would, in 1978, demand Ford recall the million or so Pintos on the road to deal with the potential for gas-tank punctures. That "smoking gun" memo would become a symbol for corporate callousness and indifference to human life, haunting Ford (and other automakers) for decades. But despite the memo's cold calculations, was Ford characterized fairly as the Kevorkian of automakers?

Perhaps not. In 1991, A Rutgers Law Journal report [PDF] showed the total number of Pinto fires, out of 2 million cars and 10 years of production, stalled at 27. It was no more than any other vehicle, averaged out, and certainly not the thousand or more suggested by Mother Jones.

Why the Ford Pinto didn't suck

The big rebuttal, and vindication?

But what of the so-called "smoking gun" memo Dowie had unearthed? Surely Ford, and Lee Iacocca himself, were part of a ruthless establishment who didn't care if its customers lived or died, right? Well, not really. Remember that the memo was a lobbying document whose audience was intended to be the NHTSA. The memo didn't refer to Pintos, or even Ford products, specifically, but American cars in general. It also considered rollovers not rear-end collisions. And that chilling assignment of value to a human life? Indeed, it was federal regulators who often considered that startling concept in their own deliberations. The value figure used in Ford's memo was the same one regulators had themselves set forth.

In fact, measured by occupant fatalities per million cars in use during 1975 and 1976, the Pinto's safety record compared favorably to other subcompacts like the AMC Gremlin, Chevy Vega, Toyota Corolla and VW Beetle.

And what of Mother Jones' Dowie? As the Car Talk blog points out, Dowie now calls the Pinto, "a fabulous vehicle that got great gas mileage," if not for that one flaw: The legendary "$11 part."

Why the Ford Pinto didn't suck

Pinto Racing Doesn't Suck

Back in 1974, Car and Driver magazine created a Pinto for racing, an exercise to prove brains and common sense were more important than an unlimited budget and superstar power. As Patrick Bedard wrote in the March, 1975 issue of Car and Driver, "It's a great car to drive, this Pinto," referring to the racer the magazine prepared for the Goodrich Radial Challenge, an IMSA-sanctioned road racing series for small sedans.

Why'd they pick a Pinto over, say, a BMW 2002 or AMC Gremlin? Current owner of the prepped Pinto, Fox Motorsports says it was a matter of comparing the car's frontal area, weight, piston displacement, handling, wheel width, and horsepower to other cars of the day that would meet the entry criteria. (Racers like Jerry Walsh had by then already been fielding Pintos in IMSA's "Baby Grand" class.)

Bedard, along with Ron Nash and company procured a 30,000-mile 1972 Pinto two-door to transform. In addition to safety, chassis and differential mods, the team traded a 200-pound IMSA weight penalty for the power gain of Ford's 2.3-liter engine, which Bedard said "tipped the scales" in the Pinto's favor. But according to Bedard, it sounds like the real advantage was in the turns, thanks to some add-ons from Mssrs. Koni and Bilstein.

"The Pinto's advantage was cornering ability," Bedard wrote. "I don't think there was another car in the B. F. Goodrich series that was quicker through the turns on a dry track. The steering is light and quick, and the suspension is direct and predictable in a way that street cars never can be. It never darts over bumps, the axle is perfectly controlled and the suspension doesn't bottom."

Need more proof of the Pinto's lack of suck? Check out the SCCA Washington, DC region's spec-Pinto series.

Members
Stats
  • Total Posts: 139,599
  • Total Topics: 16,270
  • Online today: 238
  • Online ever: 3,214 (June 20, 2025, 10:48:59 AM)
Users Online
  • Users: 0
  • Guests: 224
  • Total: 224
F&I...more

My Somewhat Begrudging Apology To Ford Pinto

ford-pinto.jpg

I never thought I’d offer an apology to the Ford Pinto, but I guess I owe it one.

I had a Pinto in the 1970s. Actually, my wife bought it a few months before we got married. The car became sort of a wedding dowry. So did the remaining 80% of the outstanding auto loan.

During a relatively brief ownership, the Pinto’s repair costs exceeded the original price of the car. It wasn’t a question of if it would fail, but when. And where. Sometimes, it simply wouldn’t start in the driveway. Other times, it would conk out at a busy intersection.

It ranks as the worst car I ever had. That was back when some auto makers made quality something like Job 100, certainly not Job 1.

Despite my bad Pinto experience, I suppose an apology is in order because of a recent blog I wrote. It centered on Toyota’s sudden-acceleration problems. But in discussing those, I invoked the memory of exploding Pintos, perpetuating an inaccuracy.

The widespread allegation was that, due to a design flaw, Pinto fuel tanks could readily blow up in rear-end collisions, setting the car and its occupants afire.

People started calling the Pinto “the barbecue that seats four.” And the lawsuits spread like wild fire.

Responding to my blog, a Ford (“I would very much prefer to keep my name out of print”) manager contacted me to set the record straight.

He says exploding Pintos were a myth that an investigation debunked nearly 20 years ago. He cites Gary Schwartz’ 1991 Rutgers Law Review paper that cut through the wild claims and examined what really happened.

Schwartz methodically determined the actual number of Pinto rear-end explosion deaths was not in the thousands, as commonly thought, but 27.

In 1975-76, the Pinto averaged 310 fatalities a year. But the similar-size Toyota Corolla averaged 313, the VW Beetle 374 and the Datsun 1200/210 came in at 405.

Yes, there were cases such as a Pinto exploding while parked on the shoulder of the road and hit from behind by a speeding pickup truck. But fiery rear-end collisions comprised only 0.6% of all fatalities back then, and the Pinto had a lower death rate in that category than the average compact or subcompact, Schwartz said after crunching the numbers. Nor was there anything about the Pinto’s rear-end design that made it particularly unsafe.

Not content to portray the Pinto as an incendiary device, ABC’s 20/20 decided to really heat things up in a 1978 broadcast containing “startling new developments.” ABC breathlessly reported that, not just Pintos, but fullsize Fords could blow up if hit from behind.

20/20 thereupon aired a video, shot by UCLA researchers, showing a Ford sedan getting rear-ended and bursting into flames. A couple of problems with that video:

One, it was shot 10 years earlier.

Two, the UCLA researchers had openly said in a published report that they intentionally rigged the vehicle with an explosive.

That’s because the test was to determine how a crash fire affected the car’s interior, not to show how easily Fords became fire balls. They said they had to use an accelerant because crash blazes on their own are so rare. They had tried to induce a vehicle fire in a crash without using an igniter, but failed.

ABC failed to mention any of that when correspondent Sylvia Chase reported on “Ford’s secret rear-end crash tests.”

We could forgive ABC for that botched reporting job. After all, it was 32 years ago. But a few weeks ago, ABC, in another one of its rigged auto exposes, showed video of a Toyota apparently accelerating on its own.

Turns out, the “runaway” vehicle had help from an associate professor. He built a gizmo with an on-off switch to provide acceleration on demand. Well, at least ABC didn’t show the Toyota slamming into a wall and bursting into flames.

In my blog, I also mentioned that Ford’s woes got worse in the 1970s with the supposed uncovering of an internal memo by a Ford attorney who allegedly calculated it would cost less to pay off wrongful-death suits than to redesign the Pinto.

It became known as the “Ford Pinto memo,” a smoking gun. But Schwartz looked into that, too. He reported the memo did not pertain to Pintos or any Ford products. Instead, it had to do with American vehicles in general.

It dealt with rollovers, not rear-end crashes. It did not address tort liability at all, let alone advocate it as a cheaper alternative to a redesign. It put a value to human life because federal regulators themselves did so.

The memo was meant for regulators’ eyes only. But it was off to the races after Mother Jones magazine got a hold of a copy and reported what wasn’t the case.

The exploding-Pinto myth lives on, largely because more Americans watch 20/20 than read the Rutgers Law Review. One wonders what people will recollect in 2040 about Toyota’s sudden accelerations, which more and more look like driver error and, in some cases, driver shams.

So I guess I owe the Pinto an apology. But it’s half-hearted, because my Pinto gave me much grief, even though, as the Ford manager notes, “it was a cheap car, built long ago and lots of things have changed, almost all for the better.”

Here goes: If I said anything that offended you, Pinto, I’m sorry. And thanks for not blowing up on me.

auto trans swap

Started by krazi, February 13, 2014, 12:29:38 PM

Previous topic - Next topic

0 Members and 1 Guest are viewing this topic.

74 PintoWagon

Bandaid fixes will bite you sooner or later they were made to run without it, if it don't work right it needs to be fixed. Dextron and Type F don't mix either, Dextron has anti foam agents in it and also soften shifts, all those so called race fluids are just Type F fluid, I use Type F in any tranny I build, after using Dextron you'd think you had a shift kit in it, lol..
Art
65 Falcon 2DR 200 IL6 with C4.

amc49

I never put any stopgap fluid improver in an ATX. If it slips you fix the problem is one of worn parts, or you simply adjust if a band. You can even adjust bands on newer modern PCM controlled cars if you look close enough. Even if there is 'no adjustment' on them. I've done it several times.

ATX shift qualities are closely tied to the viscosity of the fluid used and additives in it, when you start dickering with that you have pushed the hydraulics engineers aside to say that the millions of dollars that Ford puts into each and every transmission design is flawed and you are smarter than them. Not wise.

Rear end howling means it is most likely dead, no fixing there except the big fix or new rear end. You might check the fluid level in it but if low the damage most likely already done.

Colder spark?? I don't think so. the distributor was not modded to improve spark at all, rather  to control it. The spark comes from coil, the bigger size is to put more space between potential jump points since the coil makes more voltage. Just like going from 7 mm. wire to 8 mm., same idea.

krazi

so I bought a useless trans. I heard that the length and the slip yoke are different from a c3 to a c4. and the engine in the car is a 2.8 with a used cam and stock lifters. hard to imagine I've gone 12 years with it. must be luck. the engine I bought is a virgin 2.8. the one in the car has the smaller diameter distributor, and the new (used) one has the larger more common distributor. is there a difference in performance? (longer rotor, colder spark?) how much should I expect to pay to have the c4 rebuilt? (accidentally put dexron III mercon in it instead of type f. slips a lot. been adding lucas oil trans tune and it helps, but I think I'm pushing the limits. and the 8" rear howls when I'm on the throttle. any more help with this is appreciated and encouraged ;D
yeah, I'm Krazi!

74 PintoWagon

I mixed lifters once(when I didn't know any better and no internet,lol)cam only had about 2000mi on it, if I remember right the cam lasted about 50mi or so, called Crane up and told them what happened first thing they asked if the lifters got mixed up, I said yes  and he said "there's your problem", so new cam and lifters and I was back on the road, expensive lesson learned...
Art
65 Falcon 2DR 200 IL6 with C4.

amc49

As he says.................

It CAN be done with intelligence, it's just that most don't do that. I've done it and had engine last more than 100K. However, there are many reasons not to and disaster is waiting for you if you fit in that category.

The cam can be used if lobes are still up to height, if any is worn more than .007"-.010" you are asking for it. The high edge will be long gone by then and new lifter will not spin, rather tend to stay stay put and chew up much faster then. The lifters must still have crown on them too, they are curved on the bottom to the tune of around a 36 inch diameter radius. Much easier to get away with it with stock weak--ssed valvesprings.

Forget all that if the cam is a hi-perf one with big lobes, the high edge is gone by the first break-in of the cam and any higher spring pressures will do the cam in in as little as 30 minutes. Seen it plenty of times. I even watched some loser who 'built race engines' knock several lobes off by extreme wear simply towing manual trans car around trying to start it when he couldn't get distributor in right. Tried for 3 days to start new engine, gave up and then took it back down to find lobes missing. That was pretty wild.......................cam lobes lube by splash, he towed it long enough to run lobes bone dry and wear city. Why you always crank a new engine up and get it to 2500+ rpm fast so as to be flinging oil all over the place to lube the quickly wearing cam at that point. The high edge wears in pretty quick and then entire lobe begins to carry the load, by then lifter spinning is already established and it keeps on going. The wear then falls way off to begin the process of normal wear. One other reason why you change break in oil pretty quick on a new motor, to get those wear particles out of engine. And why you use break in lube on a new cam's first start up.


Wittsend

You didn't mention if the original engine was a 2.0/2.3 or a 2.8. If it is the 2.3 then the bellhousing for a C-4 is worth about $150.

Not to contradict AMC49 because he is absolutely correct, but I did mix/match the cam and lifters in an old 260 Falcon I had.  I just didn't know any better.  I put at least 20K miles on that engine and it still ran fine when I sold the car.  I guess I just got lucky.

  Just an FYI, the cam surface is typically ground with ever so slight an angle and the lifter bore is somewhat offset to the side.  The lifter seat is ground with a slight convex surface.  Most people think that the lifter slides on the cam.  But in reality the lobe angle and convex lifter actually cause themselves roll over each other.   You can see it here: http://books.google.com/books?id=gGtHfrXf86sC&pg=RA1-PA33&lpg=RA1-PA33&dq=lifter/lobe+relationship&source=bl&ots=gM0hbLFH-L&sig=2-0Y6-v7IbpT6qxlyFBLHXsDpVs&hl=en&sa=X&ei=e30CU4f_AoPDoAT3jYGoCQ&ved=0CFgQ6AEwCQ#v=onepage&q=lifter%2Flobe%20relationship&f=false

amc49

C3 has thirteen bolts.

Do not use used lifters on a new cam unless you want to rebuild the engine. You can use used lifters on the same cam they ran on before but mixing them with another used cam is a disaster. They wear into each other and if mixed later then they tear up whatever they run against. You can't even mix them up on same cam, they match to individual lobe, if you mix them up to be on different lobes often one tears up.

The bottom of lifter wears to match its' cam lobe, after that you cannot change them up. (You can but you'll regret it)


krazi

I recently bought a 2.8 engine and transmission. I counted the bolts on the trans pan, and came up with 13. counted it 3 times and came up with 13. I have the c4 in the car right now, which has 11 bolts. what do I need to make this mystery trans fit? I thought the c3 had 14 or 15 bolts. I know I got a good engine and trans, because I drove it once. it's only gonna be a temporary transmission, and I plan on using the v6 after I put a race cam in it. do I need new push rods and valve springs? can I reuse the lifters? any info would be helpful.
yeah, I'm Krazi!