Mini Classifieds

1977 Cruiser
Date: 06/29/2019 06:28 am
1976 Pinto runabout

Date: 03/28/2017 08:14 pm
1980 pinto/bobcat floors
Date: 07/24/2018 08:11 pm
79-80 fenders, hood, rallye wheels, light buckets, etc, C3 trans
Date: 01/04/2017 04:07 am
Hoard of Pinto parts
Date: 12/17/2016 04:14 pm
WANTED Hood Prop Rod
Date: 01/17/2017 02:47 pm
Gas Tank Sending Unit
Date: 05/22/2018 02:17 pm
1975 Ford Pinto

Date: 01/13/2020 11:02 am
Looking for Passenger side Inner Fender Apron
Date: 10/28/2018 08:45 am

Why the Ford Pinto didn’t suck

Why the Ford Pinto didn't suckThe Ford Pinto was born a low-rent, stumpy thing in Dearborn 40 years ago and grew to become one of the most infamous cars in history. The thing is that it didn't actually suck. Really.

Even after four decades, what's the first thing that comes to mind when most people think of the Ford Pinto? Ka-BLAM! The truth is the Pinto was more than that — and this is the story of how the exploding Pinto became a pre-apocalyptic narrative, how the myth was exposed, and why you should race one.

The Pinto was CEO Lee Iacocca's baby, a homegrown answer to the threat of compact-sized economy cars from Japan and Germany, the sales of which had grown significantly throughout the 1960s. Iacocca demanded the Pinto cost under $2,000, and weigh under 2,000 pounds. It was an all-hands-on-deck project, and Ford got it done in 25 months from concept to production.

Building its own small car meant Ford's buyers wouldn't have to hew to the Japanese government's size-tamping regulations; Ford would have the freedom to choose its own exterior dimensions and engine sizes based on market needs (as did Chevy with the Vega and AMC with the Gremlin). And people cold dug it.

When it was unveiled in late 1970 (ominously on September 11), US buyers noted the Pinto's pleasant shape — bringing to mind a certain tailless amphibian — and interior layout hinting at a hipster's sunken living room. Some call it one of the ugliest cars ever made, but like fans of Mischa Barton, Pinto lovers care not what others think. With its strong Kent OHV four (a distant cousin of the Lotus TwinCam), the Pinto could at least keep up with its peers, despite its drum brakes and as long as one looked past its Russian-roulette build quality.

But what of the elephant in the Pinto's room? Yes, the whole blowing-up-on-rear-end-impact thing. It all started a little more than a year after the Pinto's arrival.

 

Grimshaw v. Ford Motor Company

On May 28, 1972, Mrs. Lilly Gray and 13-year-old passenger Richard Grimshaw, set out from Anaheim, California toward Barstow in Gray's six-month-old Ford Pinto. Gray had been having trouble with the car since new, returning it to the dealer several times for stalling. After stopping in San Bernardino for gasoline, Gray got back on I-15 and accelerated to around 65 mph. Approaching traffic congestion, she moved from the left lane to the middle lane, where the car suddenly stalled and came to a stop. A 1962 Ford Galaxie, the driver unable to stop or swerve in time, rear-ended the Pinto. The Pinto's gas tank was driven forward, and punctured on the bolts of the differential housing.

As the rear wheel well sections separated from the floor pan, a full tank of fuel sprayed straight into the passenger compartment, which was engulfed in flames. Gray later died from congestive heart failure, a direct result of being nearly incinerated, while Grimshaw was burned severely and left permanently disfigured. Grimshaw and the Gray family sued Ford Motor Company (among others), and after a six-month jury trial, verdicts were returned against Ford Motor Company. Ford did not contest amount of compensatory damages awarded to Grimshaw and the Gray family, and a jury awarded the plaintiffs $125 million, which the judge in the case subsequently reduced to the low seven figures. Other crashes and other lawsuits followed.

Why the Ford Pinto didn't suck

Mother Jones and Pinto Madness

In 1977, Mark Dowie, business manager of Mother Jones magazine published an article on the Pinto's "exploding gas tanks." It's the same article in which we first heard the chilling phrase, "How much does Ford think your life is worth?" Dowie had spent days sorting through filing cabinets at the Department of Transportation, examining paperwork Ford had produced as part of a lobbying effort to defeat a federal rear-end collision standard. That's where Dowie uncovered an innocuous-looking memo entitled "Fatalities Associated with Crash-Induced Fuel Leakage and Fires."

The Car Talk blog describes why the memo proved so damning.

In it, Ford's director of auto safety estimated that equipping the Pinto with [an] $11 part would prevent 180 burn deaths, 180 serious burn injuries and 2,100 burned cars, for a total cost of $137 million. Paying out $200,000 per death, $67,000 per injury and $700 per vehicle would cost only $49.15 million.

The government would, in 1978, demand Ford recall the million or so Pintos on the road to deal with the potential for gas-tank punctures. That "smoking gun" memo would become a symbol for corporate callousness and indifference to human life, haunting Ford (and other automakers) for decades. But despite the memo's cold calculations, was Ford characterized fairly as the Kevorkian of automakers?

Perhaps not. In 1991, A Rutgers Law Journal report [PDF] showed the total number of Pinto fires, out of 2 million cars and 10 years of production, stalled at 27. It was no more than any other vehicle, averaged out, and certainly not the thousand or more suggested by Mother Jones.

Why the Ford Pinto didn't suck

The big rebuttal, and vindication?

But what of the so-called "smoking gun" memo Dowie had unearthed? Surely Ford, and Lee Iacocca himself, were part of a ruthless establishment who didn't care if its customers lived or died, right? Well, not really. Remember that the memo was a lobbying document whose audience was intended to be the NHTSA. The memo didn't refer to Pintos, or even Ford products, specifically, but American cars in general. It also considered rollovers not rear-end collisions. And that chilling assignment of value to a human life? Indeed, it was federal regulators who often considered that startling concept in their own deliberations. The value figure used in Ford's memo was the same one regulators had themselves set forth.

In fact, measured by occupant fatalities per million cars in use during 1975 and 1976, the Pinto's safety record compared favorably to other subcompacts like the AMC Gremlin, Chevy Vega, Toyota Corolla and VW Beetle.

And what of Mother Jones' Dowie? As the Car Talk blog points out, Dowie now calls the Pinto, "a fabulous vehicle that got great gas mileage," if not for that one flaw: The legendary "$11 part."

Why the Ford Pinto didn't suck

Pinto Racing Doesn't Suck

Back in 1974, Car and Driver magazine created a Pinto for racing, an exercise to prove brains and common sense were more important than an unlimited budget and superstar power. As Patrick Bedard wrote in the March, 1975 issue of Car and Driver, "It's a great car to drive, this Pinto," referring to the racer the magazine prepared for the Goodrich Radial Challenge, an IMSA-sanctioned road racing series for small sedans.

Why'd they pick a Pinto over, say, a BMW 2002 or AMC Gremlin? Current owner of the prepped Pinto, Fox Motorsports says it was a matter of comparing the car's frontal area, weight, piston displacement, handling, wheel width, and horsepower to other cars of the day that would meet the entry criteria. (Racers like Jerry Walsh had by then already been fielding Pintos in IMSA's "Baby Grand" class.)

Bedard, along with Ron Nash and company procured a 30,000-mile 1972 Pinto two-door to transform. In addition to safety, chassis and differential mods, the team traded a 200-pound IMSA weight penalty for the power gain of Ford's 2.3-liter engine, which Bedard said "tipped the scales" in the Pinto's favor. But according to Bedard, it sounds like the real advantage was in the turns, thanks to some add-ons from Mssrs. Koni and Bilstein.

"The Pinto's advantage was cornering ability," Bedard wrote. "I don't think there was another car in the B. F. Goodrich series that was quicker through the turns on a dry track. The steering is light and quick, and the suspension is direct and predictable in a way that street cars never can be. It never darts over bumps, the axle is perfectly controlled and the suspension doesn't bottom."

Need more proof of the Pinto's lack of suck? Check out the SCCA Washington, DC region's spec-Pinto series.

Members
Stats
  • Total Posts: 139,575
  • Total Topics: 16,267
  • Online today: 1,431
  • Online ever: 2,670 (Yesterday at 01:57:20 AM)
Users Online
  • Users: 0
  • Guests: 993
  • Total: 993
F&I...more

My Somewhat Begrudging Apology To Ford Pinto

ford-pinto.jpg

I never thought I’d offer an apology to the Ford Pinto, but I guess I owe it one.

I had a Pinto in the 1970s. Actually, my wife bought it a few months before we got married. The car became sort of a wedding dowry. So did the remaining 80% of the outstanding auto loan.

During a relatively brief ownership, the Pinto’s repair costs exceeded the original price of the car. It wasn’t a question of if it would fail, but when. And where. Sometimes, it simply wouldn’t start in the driveway. Other times, it would conk out at a busy intersection.

It ranks as the worst car I ever had. That was back when some auto makers made quality something like Job 100, certainly not Job 1.

Despite my bad Pinto experience, I suppose an apology is in order because of a recent blog I wrote. It centered on Toyota’s sudden-acceleration problems. But in discussing those, I invoked the memory of exploding Pintos, perpetuating an inaccuracy.

The widespread allegation was that, due to a design flaw, Pinto fuel tanks could readily blow up in rear-end collisions, setting the car and its occupants afire.

People started calling the Pinto “the barbecue that seats four.” And the lawsuits spread like wild fire.

Responding to my blog, a Ford (“I would very much prefer to keep my name out of print”) manager contacted me to set the record straight.

He says exploding Pintos were a myth that an investigation debunked nearly 20 years ago. He cites Gary Schwartz’ 1991 Rutgers Law Review paper that cut through the wild claims and examined what really happened.

Schwartz methodically determined the actual number of Pinto rear-end explosion deaths was not in the thousands, as commonly thought, but 27.

In 1975-76, the Pinto averaged 310 fatalities a year. But the similar-size Toyota Corolla averaged 313, the VW Beetle 374 and the Datsun 1200/210 came in at 405.

Yes, there were cases such as a Pinto exploding while parked on the shoulder of the road and hit from behind by a speeding pickup truck. But fiery rear-end collisions comprised only 0.6% of all fatalities back then, and the Pinto had a lower death rate in that category than the average compact or subcompact, Schwartz said after crunching the numbers. Nor was there anything about the Pinto’s rear-end design that made it particularly unsafe.

Not content to portray the Pinto as an incendiary device, ABC’s 20/20 decided to really heat things up in a 1978 broadcast containing “startling new developments.” ABC breathlessly reported that, not just Pintos, but fullsize Fords could blow up if hit from behind.

20/20 thereupon aired a video, shot by UCLA researchers, showing a Ford sedan getting rear-ended and bursting into flames. A couple of problems with that video:

One, it was shot 10 years earlier.

Two, the UCLA researchers had openly said in a published report that they intentionally rigged the vehicle with an explosive.

That’s because the test was to determine how a crash fire affected the car’s interior, not to show how easily Fords became fire balls. They said they had to use an accelerant because crash blazes on their own are so rare. They had tried to induce a vehicle fire in a crash without using an igniter, but failed.

ABC failed to mention any of that when correspondent Sylvia Chase reported on “Ford’s secret rear-end crash tests.”

We could forgive ABC for that botched reporting job. After all, it was 32 years ago. But a few weeks ago, ABC, in another one of its rigged auto exposes, showed video of a Toyota apparently accelerating on its own.

Turns out, the “runaway” vehicle had help from an associate professor. He built a gizmo with an on-off switch to provide acceleration on demand. Well, at least ABC didn’t show the Toyota slamming into a wall and bursting into flames.

In my blog, I also mentioned that Ford’s woes got worse in the 1970s with the supposed uncovering of an internal memo by a Ford attorney who allegedly calculated it would cost less to pay off wrongful-death suits than to redesign the Pinto.

It became known as the “Ford Pinto memo,” a smoking gun. But Schwartz looked into that, too. He reported the memo did not pertain to Pintos or any Ford products. Instead, it had to do with American vehicles in general.

It dealt with rollovers, not rear-end crashes. It did not address tort liability at all, let alone advocate it as a cheaper alternative to a redesign. It put a value to human life because federal regulators themselves did so.

The memo was meant for regulators’ eyes only. But it was off to the races after Mother Jones magazine got a hold of a copy and reported what wasn’t the case.

The exploding-Pinto myth lives on, largely because more Americans watch 20/20 than read the Rutgers Law Review. One wonders what people will recollect in 2040 about Toyota’s sudden accelerations, which more and more look like driver error and, in some cases, driver shams.

So I guess I owe the Pinto an apology. But it’s half-hearted, because my Pinto gave me much grief, even though, as the Ford manager notes, “it was a cheap car, built long ago and lots of things have changed, almost all for the better.”

Here goes: If I said anything that offended you, Pinto, I’m sorry. And thanks for not blowing up on me.

wire welder

Started by dholvrsn, July 25, 2006, 11:21:39 AM

Previous topic - Next topic

0 Members and 1 Guest are viewing this topic.

goodolboydws

Ditto, earthquake.
Don't forget the tiny pieces of rust and road that seem to always find a way to get into your eyes at the least opportune moments, eye protection or no.   

And welding sparks or blobs down the front or back of a shirt or right through the top of nylon sneakers or on the top of your head right through a thin baseball cap is no fun either, as I quickly discovered a few years ago.  Not enough follicles left up there to lose any more than necessary now.

Much as I hate the bother, in addition to the always sensible long gauntlet gloves and helmet, I shortly took to wearing leather boots, a closeable collar at the very least (if not my combo burn resistant cloth and leather sleeved welding shirt),  and a welders cloth cap with the bill turned around backwards to protect my neck ALL the time when welding. If you're anything like me, you'll sweat like an overworked team of horses in the Summer, but at least end up with fewer holes in your hide.

earthquake

Good point I had never thought of that,not having it happen YET.I'll take that advise.And there are a great many things that create that jerk.I dropped a ratchet and in trying to dodge it gave myself a nice mouse on the forehead with a caliper.Such Fun.
73 sedan parts car,80 crusin wagon conversion,76 F 250 460 SCJ,74 Ranchero 4x4,88 mustang lx convertable,and the readheaded step child 86 uhhh Chevy 4x4(Sorry guys it was cheap)

UltimatePinto

Hi all,

Haven't been around the site in a while due to drowning in projects and clutter.
I weld for a living and have a Miller wire feed with a separate attachment gun that I use for aluminum wire. I've had the unit for some time and am happy with it.

I agree with just about all that I have seen in this post. I would agree that you should get a good unit and pay the price as an investment, helmet and all. However I would also agree if you don't have a shop or are planning to move in the future, the 110 units will more than suffice for any welding you need to do on Pinto's, or just about any vehicle.

Just a word of advice though. If you plan to do any overhead under a vehicle on jackstands, (having to lay on your side instead of standing up), be sure to wear ear plugs!
You haven't lived until you get a nice round ball of spatter down your ear canal. You hear and feel the wax boil.
Your first reaction will be to jerk your head away from the pain. When you do the vehicle does not move.
Trust me on this one.

Al

earthquake

Shucks sell a 90 amp flux wire feed welder for $179.00.for the hobbiest it should work fine.But buy the helmet.
73 sedan parts car,80 crusin wagon conversion,76 F 250 460 SCJ,74 Ranchero 4x4,88 mustang lx convertable,and the readheaded step child 86 uhhh Chevy 4x4(Sorry guys it was cheap)

Stroker

Can't hardly beat this deal http://www.toolking.com/productinfo.aspx?productid=17860 even the pros use one of these smaller units when the job doesnt call for something bigger, they are just more practical then a big 250 or whatever.

goodolboydws

robw,

You do have a good point about eye protection here.

There is the possibility of having a problem with ANY auto darkening helmet, name brand or no, import or no.  There is a certain lag time with ALL of these helmets, usually a very small fraction of a second, (generally as short as 1-2 THOUSANDTHS of a second up to maybe 20 thousandths). Even the shortest amount of lag time to full darkening has a CUMULATIVE effect, as does any helmet shield "leakage" where some light from the welding flash sneaks past the edges or through gaps of the shield/helmet and makes it to the users eyes.

If I were going to be using a self darkening helmet in an assembly line situation, welding all day long through hundreds or possibly thousands of on/off cycles, you can bet that I would get something with the shortest possible lag time. With few welds per day, or with only occasional use however, the cumulative exposure using a shield with a longer lag time is obviously not as high as even a much faster-to-darken helmet used for many more cycles.
Using the above example, compare a 20/1000 sec. speed helmet with a 1/1000 sec one. It would take 10 times the number of weld cycles for the faster helmet to equal the total exposure time, but if the slower helmet was only used for 10 weld cycles per day average and the faster one for 200 per day average, the total exposure would be the same.

With global manufacturing and assembly being the standard these days, simply buying a "name" brand or one that may have been associated with one particular country has (with rare exceptions) much less meaning than ever before.

Many of the essential and critical COMPONENTS for tools and accessories such as the wire welders and helmets (and most power tools) are themselves made in unnamed factories across the world, with the same components being used in many different brands and the finished products only labeled after the machines are completely assembled-from parts that may come from several different countries and be assembled in yet another country.

Due to this typical modern manufacturing model, the traditional reputation of brands themselves have become less important, while the warranty, accessories, parts availability AFTER warranty expiration and the ability to obtain service on the tool or machine have become more important.
Many of the cheapest tools have no warranty at all (or a meaningless one that entails spending more money to send it in for repair than it would be worth to fix)., and yet with limited use they may still fill a need for cash strapped buyers. As always, high price or low, caveat emptor (let the buyer beware) should be a guide.

Unfortunately, your father obviously got either a bum helmet shield or possibly the batteries are just shot in his or making poor contact, slowing the darkening time time down dramatically. Think of how weak batteries in a flash camera slow down the recovery time for the flash between pictures. It's the same principle.
A welding shield that takes anywhere near a second or 2 to darken should not be used, unless no other one offering better eye protection is available, in which case, it's still going to a LOT better than using nothing at all.  Be safe.

robw

Me and the old man have a older millermatic 350 it is quite large(you have to roll it around) it had a decent price tag on it at the time. but well worth it. it will weld anything from sheet metal to 1/2 in. only found that out when i was building a suspension for a off-road truck.as for the auto darkening helmets I found it is better not to buy the cheapest one there is, due to the fact that a lot of them are made in china or worse places,and do you think they give a damn about your eyes. spend alittle more and get one with name on it. my old man bought a cheapo one and it wouldn't darken until like two seconds after you started to weld.

DragonWagon

Good tips goodolboydws! I do have the .023 kit, just not the tank to go with it yet. When I bought it, it had a new 10 lb spool of .03 flux on it which I'm still using. Harbor Freight has the auto-darkening helmets for $50. Picked one up a couple months ago and love it!

dholvrsn, you really can't go wrong with one of these things, unless you live in an apartment. If you do, don't expect to get your deposit back  ;).

Buying a cheap wirefeed is just asking for trouble. A good one is an investment, but will last for a long time. Guess you need to assess how much and what kind of welding you plan on doing and go from there.
1976 mpg Wagon. The start of it all.
1977 Cruising Wagon, to be turboed.
1979 glass hatchback. No motor atm.
1980 wagon parts car.

goodolboydws

Same brand recommendation.

These aren't the cheapest units out there, not by a long shot, but sometimes you have to bite the bullet if you expect to get a quality tool, and unless you drop it off a truck or it gets stolen, or you use it in an industrial setting, and do welding every day, you may not have to buy a replacement unit. Ever.  Check out how long their warranty is-it was 3 years when I got mine and I believe the same unit now has a 5 or 6 year warranty.

Whatever brand you decide to go with, I'd get the highest amperage unit that you can run on 110V as a first unit, you may never need a bigger one.

I've had my Hobart Handler 135(amps) for over 6 years and have had no equipment complaints yet. It's rated to weld up to about 3/16" steel in a single pass With good weld penetration, and I can verify that this is an accurate rating. The duty cycle for actual continuous welding time is fairly low, as it is on all of the 110V machines (about 20%max. usable time at the highest amperage setting) but for most smaller and thinner work, the higher duty cycle  should be sufficient to weld nearly continuously, which honestly for most work is not something that you are liable to be doing.  I've welded from under 1/16" to over 1/2" thick steel several times when repairing farm implements (with the 135A unit), using prepared joints and multiple passes.

Most hobby welding people will never need to weld steel this thick.

I use mine with 75/25 Argon/CO2 mixed gas exclusively because with mild steel it yields a much cleaner weld (compared to NOT using gas), with less splatter, so grinding and clean up are minimized, but some poeple are happy enough with the beads' appearance without using gas, especially if they have only been accustomed to stick welding. For some purposes (like outdoor welding), you are liable to use flux core wire without gas anyway, due to the difficulty in protecting the joint from wind.

One thing that I've noticed with the 135 unit is that the weld penetration is significantly deeper when using the .023 wire at the highest amperage setting, as compared to the .030 wire that the unit can also use. 

I think that they now have a 140(amps) unit that will still run on 110V.

P.S. Don't cheap out.
Now that the price has dropped, get a self-darkening helmet right away if you can afford it. (I found one mail order for under $50.00.) If you have even average talent, you'll be amazed at how quickly your welding will improve (and it will be better) when using one of these, as well as how much less fiddling you do compared with a standard helmet, even if it's a flip face or flip view model.

Dragon Wagon:

One thing that I've repeatedly noticed with the 135 amp unit is that the weld penetration is significantly deeper when using the .023 wire at the highest amperage setting, as compared to the .030 wire that the unit can also use. Probably along the lines of: the thinner wire heats up more than the thicker wire with the same current, then transfers the heat to the metal being welded in a slightly smaller spot, so IT heats up more.


Anyway, you have to speed up the wire feed rate (due to the smaller cross sectional area of the wire) to get the same rate of deposition, and it may seem strange but when I'm welding at the thick end of the range of the units' rating, the thin wire seems to work out better for penetration and it also CAN give a flatter bead, (which may be more useful in certain situations, such as when multiple passes are required) although the bead appearance can often be made similar between the 2 diameters when varying wire feed speed and amperage settings. 


DragonWagon

I lucked out a while back and snagged up a Lincoln Weldpac 100 at a garage sale. Portable 120 volt unit. They claim it can handle up to 1/4" steel, but I doubt it would have very good penetration on that size of material. Seems to work great on 1/8" and smaller stock. They are about $350 new, so not the cheapest around. Miller seems to be pretty dependable as well. Don't know how much they cost. I'd stay away from the cheap / noname brands. Remember, if you plan on using it to weld body panels, you'll need the solid wire and shielding gas, not flux core. Flux core is fine for thicker stuff, but doesn't make as clean of weld.
1976 mpg Wagon. The start of it all.
1977 Cruising Wagon, to be turboed.
1979 glass hatchback. No motor atm.
1980 wagon parts car.

Gaslight

I use one of the new Hobarts.  Hobart got bought by Miller so now all the insides are really Miller.  Been a good unit at home.

Jake
My new answering machine message:   
"I am not available right now, but thank you for caring enough to call.
I am making some changes in my life.  Please leave a message after the beep.
If I do not return your call, you are one of the changes."

dholvrsn

Can anybody recommend one for the hobbyist?
'80 MPG Pony, '80-'92
'79 porthole wagon, '06-on
'80 trunk model. '17-on
-----
'98 Dodge Ram 1500
'95 Buick Riviera
'63 Studebaker Champ
'57 Studebaker Silver Hawk
'51 Studebaker Commander Starlight
'47 Studebaker Champion
'41 Studebaker Commander Land Cruiser