Mini Classifieds

1980 Pinto Pony for sale

Date: 08/21/2021 03:54 pm
Wanted Postal Pinto
Date: 08/30/2021 03:20 pm
postal pinto
Date: 06/03/2020 09:31 am
Misc pinto parts 71-73 2.0
Date: 05/05/2020 11:56 pm
Wanted - 71-73 Pinto grill
Date: 12/15/2016 03:32 pm
1976-1980 A/C condensor

Date: 09/21/2020 10:43 pm
1971 2 lt Cam
Date: 10/10/2020 06:27 pm
1970-1973 British 4 Speed Manual; Parts or Whole
Date: 03/17/2019 03:57 am
1972 Pinto SCCA BS race car

Date: 10/23/2018 04:01 pm

Why the Ford Pinto didn’t suck

Why the Ford Pinto didn't suckThe Ford Pinto was born a low-rent, stumpy thing in Dearborn 40 years ago and grew to become one of the most infamous cars in history. The thing is that it didn't actually suck. Really.

Even after four decades, what's the first thing that comes to mind when most people think of the Ford Pinto? Ka-BLAM! The truth is the Pinto was more than that — and this is the story of how the exploding Pinto became a pre-apocalyptic narrative, how the myth was exposed, and why you should race one.

The Pinto was CEO Lee Iacocca's baby, a homegrown answer to the threat of compact-sized economy cars from Japan and Germany, the sales of which had grown significantly throughout the 1960s. Iacocca demanded the Pinto cost under $2,000, and weigh under 2,000 pounds. It was an all-hands-on-deck project, and Ford got it done in 25 months from concept to production.

Building its own small car meant Ford's buyers wouldn't have to hew to the Japanese government's size-tamping regulations; Ford would have the freedom to choose its own exterior dimensions and engine sizes based on market needs (as did Chevy with the Vega and AMC with the Gremlin). And people cold dug it.

When it was unveiled in late 1970 (ominously on September 11), US buyers noted the Pinto's pleasant shape — bringing to mind a certain tailless amphibian — and interior layout hinting at a hipster's sunken living room. Some call it one of the ugliest cars ever made, but like fans of Mischa Barton, Pinto lovers care not what others think. With its strong Kent OHV four (a distant cousin of the Lotus TwinCam), the Pinto could at least keep up with its peers, despite its drum brakes and as long as one looked past its Russian-roulette build quality.

But what of the elephant in the Pinto's room? Yes, the whole blowing-up-on-rear-end-impact thing. It all started a little more than a year after the Pinto's arrival.

 

Grimshaw v. Ford Motor Company

On May 28, 1972, Mrs. Lilly Gray and 13-year-old passenger Richard Grimshaw, set out from Anaheim, California toward Barstow in Gray's six-month-old Ford Pinto. Gray had been having trouble with the car since new, returning it to the dealer several times for stalling. After stopping in San Bernardino for gasoline, Gray got back on I-15 and accelerated to around 65 mph. Approaching traffic congestion, she moved from the left lane to the middle lane, where the car suddenly stalled and came to a stop. A 1962 Ford Galaxie, the driver unable to stop or swerve in time, rear-ended the Pinto. The Pinto's gas tank was driven forward, and punctured on the bolts of the differential housing.

As the rear wheel well sections separated from the floor pan, a full tank of fuel sprayed straight into the passenger compartment, which was engulfed in flames. Gray later died from congestive heart failure, a direct result of being nearly incinerated, while Grimshaw was burned severely and left permanently disfigured. Grimshaw and the Gray family sued Ford Motor Company (among others), and after a six-month jury trial, verdicts were returned against Ford Motor Company. Ford did not contest amount of compensatory damages awarded to Grimshaw and the Gray family, and a jury awarded the plaintiffs $125 million, which the judge in the case subsequently reduced to the low seven figures. Other crashes and other lawsuits followed.

Why the Ford Pinto didn't suck

Mother Jones and Pinto Madness

In 1977, Mark Dowie, business manager of Mother Jones magazine published an article on the Pinto's "exploding gas tanks." It's the same article in which we first heard the chilling phrase, "How much does Ford think your life is worth?" Dowie had spent days sorting through filing cabinets at the Department of Transportation, examining paperwork Ford had produced as part of a lobbying effort to defeat a federal rear-end collision standard. That's where Dowie uncovered an innocuous-looking memo entitled "Fatalities Associated with Crash-Induced Fuel Leakage and Fires."

The Car Talk blog describes why the memo proved so damning.

In it, Ford's director of auto safety estimated that equipping the Pinto with [an] $11 part would prevent 180 burn deaths, 180 serious burn injuries and 2,100 burned cars, for a total cost of $137 million. Paying out $200,000 per death, $67,000 per injury and $700 per vehicle would cost only $49.15 million.

The government would, in 1978, demand Ford recall the million or so Pintos on the road to deal with the potential for gas-tank punctures. That "smoking gun" memo would become a symbol for corporate callousness and indifference to human life, haunting Ford (and other automakers) for decades. But despite the memo's cold calculations, was Ford characterized fairly as the Kevorkian of automakers?

Perhaps not. In 1991, A Rutgers Law Journal report [PDF] showed the total number of Pinto fires, out of 2 million cars and 10 years of production, stalled at 27. It was no more than any other vehicle, averaged out, and certainly not the thousand or more suggested by Mother Jones.

Why the Ford Pinto didn't suck

The big rebuttal, and vindication?

But what of the so-called "smoking gun" memo Dowie had unearthed? Surely Ford, and Lee Iacocca himself, were part of a ruthless establishment who didn't care if its customers lived or died, right? Well, not really. Remember that the memo was a lobbying document whose audience was intended to be the NHTSA. The memo didn't refer to Pintos, or even Ford products, specifically, but American cars in general. It also considered rollovers not rear-end collisions. And that chilling assignment of value to a human life? Indeed, it was federal regulators who often considered that startling concept in their own deliberations. The value figure used in Ford's memo was the same one regulators had themselves set forth.

In fact, measured by occupant fatalities per million cars in use during 1975 and 1976, the Pinto's safety record compared favorably to other subcompacts like the AMC Gremlin, Chevy Vega, Toyota Corolla and VW Beetle.

And what of Mother Jones' Dowie? As the Car Talk blog points out, Dowie now calls the Pinto, "a fabulous vehicle that got great gas mileage," if not for that one flaw: The legendary "$11 part."

Why the Ford Pinto didn't suck

Pinto Racing Doesn't Suck

Back in 1974, Car and Driver magazine created a Pinto for racing, an exercise to prove brains and common sense were more important than an unlimited budget and superstar power. As Patrick Bedard wrote in the March, 1975 issue of Car and Driver, "It's a great car to drive, this Pinto," referring to the racer the magazine prepared for the Goodrich Radial Challenge, an IMSA-sanctioned road racing series for small sedans.

Why'd they pick a Pinto over, say, a BMW 2002 or AMC Gremlin? Current owner of the prepped Pinto, Fox Motorsports says it was a matter of comparing the car's frontal area, weight, piston displacement, handling, wheel width, and horsepower to other cars of the day that would meet the entry criteria. (Racers like Jerry Walsh had by then already been fielding Pintos in IMSA's "Baby Grand" class.)

Bedard, along with Ron Nash and company procured a 30,000-mile 1972 Pinto two-door to transform. In addition to safety, chassis and differential mods, the team traded a 200-pound IMSA weight penalty for the power gain of Ford's 2.3-liter engine, which Bedard said "tipped the scales" in the Pinto's favor. But according to Bedard, it sounds like the real advantage was in the turns, thanks to some add-ons from Mssrs. Koni and Bilstein.

"The Pinto's advantage was cornering ability," Bedard wrote. "I don't think there was another car in the B. F. Goodrich series that was quicker through the turns on a dry track. The steering is light and quick, and the suspension is direct and predictable in a way that street cars never can be. It never darts over bumps, the axle is perfectly controlled and the suspension doesn't bottom."

Need more proof of the Pinto's lack of suck? Check out the SCCA Washington, DC region's spec-Pinto series.

Members
  • Total Members: 7,895
  • Latest: tdok
Stats
  • Total Posts: 139,584
  • Total Topics: 16,270
  • Online today: 506
  • Online ever: 3,214 (June 20, 2025, 10:48:59 AM)
Users Online
  • Users: 0
  • Guests: 214
  • Total: 214
F&I...more

My Somewhat Begrudging Apology To Ford Pinto

ford-pinto.jpg

I never thought I’d offer an apology to the Ford Pinto, but I guess I owe it one.

I had a Pinto in the 1970s. Actually, my wife bought it a few months before we got married. The car became sort of a wedding dowry. So did the remaining 80% of the outstanding auto loan.

During a relatively brief ownership, the Pinto’s repair costs exceeded the original price of the car. It wasn’t a question of if it would fail, but when. And where. Sometimes, it simply wouldn’t start in the driveway. Other times, it would conk out at a busy intersection.

It ranks as the worst car I ever had. That was back when some auto makers made quality something like Job 100, certainly not Job 1.

Despite my bad Pinto experience, I suppose an apology is in order because of a recent blog I wrote. It centered on Toyota’s sudden-acceleration problems. But in discussing those, I invoked the memory of exploding Pintos, perpetuating an inaccuracy.

The widespread allegation was that, due to a design flaw, Pinto fuel tanks could readily blow up in rear-end collisions, setting the car and its occupants afire.

People started calling the Pinto “the barbecue that seats four.” And the lawsuits spread like wild fire.

Responding to my blog, a Ford (“I would very much prefer to keep my name out of print”) manager contacted me to set the record straight.

He says exploding Pintos were a myth that an investigation debunked nearly 20 years ago. He cites Gary Schwartz’ 1991 Rutgers Law Review paper that cut through the wild claims and examined what really happened.

Schwartz methodically determined the actual number of Pinto rear-end explosion deaths was not in the thousands, as commonly thought, but 27.

In 1975-76, the Pinto averaged 310 fatalities a year. But the similar-size Toyota Corolla averaged 313, the VW Beetle 374 and the Datsun 1200/210 came in at 405.

Yes, there were cases such as a Pinto exploding while parked on the shoulder of the road and hit from behind by a speeding pickup truck. But fiery rear-end collisions comprised only 0.6% of all fatalities back then, and the Pinto had a lower death rate in that category than the average compact or subcompact, Schwartz said after crunching the numbers. Nor was there anything about the Pinto’s rear-end design that made it particularly unsafe.

Not content to portray the Pinto as an incendiary device, ABC’s 20/20 decided to really heat things up in a 1978 broadcast containing “startling new developments.” ABC breathlessly reported that, not just Pintos, but fullsize Fords could blow up if hit from behind.

20/20 thereupon aired a video, shot by UCLA researchers, showing a Ford sedan getting rear-ended and bursting into flames. A couple of problems with that video:

One, it was shot 10 years earlier.

Two, the UCLA researchers had openly said in a published report that they intentionally rigged the vehicle with an explosive.

That’s because the test was to determine how a crash fire affected the car’s interior, not to show how easily Fords became fire balls. They said they had to use an accelerant because crash blazes on their own are so rare. They had tried to induce a vehicle fire in a crash without using an igniter, but failed.

ABC failed to mention any of that when correspondent Sylvia Chase reported on “Ford’s secret rear-end crash tests.”

We could forgive ABC for that botched reporting job. After all, it was 32 years ago. But a few weeks ago, ABC, in another one of its rigged auto exposes, showed video of a Toyota apparently accelerating on its own.

Turns out, the “runaway” vehicle had help from an associate professor. He built a gizmo with an on-off switch to provide acceleration on demand. Well, at least ABC didn’t show the Toyota slamming into a wall and bursting into flames.

In my blog, I also mentioned that Ford’s woes got worse in the 1970s with the supposed uncovering of an internal memo by a Ford attorney who allegedly calculated it would cost less to pay off wrongful-death suits than to redesign the Pinto.

It became known as the “Ford Pinto memo,” a smoking gun. But Schwartz looked into that, too. He reported the memo did not pertain to Pintos or any Ford products. Instead, it had to do with American vehicles in general.

It dealt with rollovers, not rear-end crashes. It did not address tort liability at all, let alone advocate it as a cheaper alternative to a redesign. It put a value to human life because federal regulators themselves did so.

The memo was meant for regulators’ eyes only. But it was off to the races after Mother Jones magazine got a hold of a copy and reported what wasn’t the case.

The exploding-Pinto myth lives on, largely because more Americans watch 20/20 than read the Rutgers Law Review. One wonders what people will recollect in 2040 about Toyota’s sudden accelerations, which more and more look like driver error and, in some cases, driver shams.

So I guess I owe the Pinto an apology. But it’s half-hearted, because my Pinto gave me much grief, even though, as the Ford manager notes, “it was a cheap car, built long ago and lots of things have changed, almost all for the better.”

Here goes: If I said anything that offended you, Pinto, I’m sorry. And thanks for not blowing up on me.

91 2.3L in a CJ2A

Started by dillonwilkinson, January 28, 2015, 10:09:04 AM

Previous topic - Next topic

0 Members and 1 Guest are viewing this topic.

how to wire fuel injection

fuel injection
3 (75%)
carb
1 (25%)

Total Members Voted: 4

amc49

The swap is child's play but that is not what OP asked, one either can read or they can't...........LOL

'...what the person was refering to with the 6 wire comment is ..... with a harness for the engine there are only a few wires that need to be connected...'

Then he needs to make that perfectly clear, the answer was nothing like that and highly misleading. We can go even further to say car only needs two wires only....at battery terminals....and essentially still be correct but what good is that?

FYI, I have wired entire cars and drivetrains many times in my life; if comments directed at me. Piece of cake.

Yes one could pull wiring out of any car with the proper wiring in it............the schematic is the thing, once you have that you are set to go. Some Ford ones are harder to read than others though, they change the style and layout up from time to time.

dianne

Quote from: pinto_one on February 02, 2015, 12:53:04 PM
The wiring should be done after all the hard parts are in place and bolted down,  wiring diagrams are out there for the year motor and ECM you are using , autozone does have the diagrams on line to copy and print, if you removed the whole harness from the car you will have to trim it down to shorten it, ECM placement is nice above the glove box , high and dry, max wire length from there is less than four feet,  when you start to make your harness chose a place the is quite and free of kids , nagging love ones and phones, next clean the wire before you start cutting, use a good soap , do not use , MEK, lacquer thinner , it will remove the stripes on the wires,  solder the wires together using a western union joint, and cover with heat shrink tubing , once you have every thing in place double check , once you let the smoke out of the ECM you can not put the smoke back in, its toast,  learn what each sensor is and what it does, and where the wires goes , the more you learn the easy er the out come, and do wire in the plug for the code reader, I have seen a few people have cut that out , bad when your on the side of the road trying to figure out what is wrong , hope this helps some poor (sap) individual from letting the smoke out, later Blaine :o

We have Mitchell 1 and can print them if anyone wants.
Vehicles:

- 1972 Plymouth Duster (To be a Pro Street)
- 1973 Ford Pinto wagon (registered ride 195)
- 1976 Mustang II mini-stock
- 1978 Mustang King Cobra II
- 1979 Ford Pinto Runabout
- 1986 Chevy K5 Blazer
- 1997 Suzuki Marauder

FORD: Federal Ownership Respectfully Denied

pinto_one

The wiring should be done after all the hard parts are in place and bolted down,  wiring diagrams are out there for the year motor and ECM you are using , autozone does have the diagrams on line to copy and print, if you removed the whole harness from the car you will have to trim it down to shorten it, ECM placement is nice above the glove box , high and dry, max wire length from there is less than four feet,  when you start to make your harness chose a place the is quite and free of kids , nagging love ones and phones, next clean the wire before you start cutting, use a good soap , do not use , MEK, lacquer thinner , it will remove the stripes on the wires,  solder the wires together using a western union joint, and cover with heat shrink tubing , once you have every thing in place double check , once you let the smoke out of the ECM you can not put the smoke back in, its toast,  learn what each sensor is and what it does, and where the wires goes , the more you learn the easy er the out come, and do wire in the plug for the code reader, I have seen a few people have cut that out , bad when your on the side of the road trying to figure out what is wrong , hope this helps some poor (sap) individual from letting the smoke out, later Blaine :o
76 Pinto sedan V6 , 79 pinto cruiser wagon V6 soon to be diesel or 4.0

dianne

Quote from: Pinturbo75 on February 02, 2015, 07:46:41 AM
what the person was refering to with the 6 wire comment is ..... with a harness for the engine there are only a few wires that need to be connected to the vehicle to obtain power for the ecu and fuel circuits... along witha couple grounds....some people on here... who have never even attempted this swap,,,,, act like they invented it ..... if you have never done it and all your info is hearsay or what youve read.... then post the links up and shut the hell up

I
ll post a zillion pics of the swap for the next ones. Pinto_one has done it, but a turbo I guess.
Vehicles:

- 1972 Plymouth Duster (To be a Pro Street)
- 1973 Ford Pinto wagon (registered ride 195)
- 1976 Mustang II mini-stock
- 1978 Mustang King Cobra II
- 1979 Ford Pinto Runabout
- 1986 Chevy K5 Blazer
- 1997 Suzuki Marauder

FORD: Federal Ownership Respectfully Denied

Pinturbo75

what the person was refering to with the 6 wire comment is ..... with a harness for the engine there are only a few wires that need to be connected to the vehicle to obtain power for the ecu and fuel circuits... along witha couple grounds....some people on here... who have never even attempted this swap,,,,, act like they invented it ..... if you have never done it and all your info is hearsay or what youve read.... then post the links up and shut the hell up
75 turbo pinto trunk, megasquirt2, 133lb injectors, bv head, precision 6265 turbo, 3" exhaust,bobs log, 8.8, t5,, subframe connectors, 65 mm tb, frontmount ic, traction bars, 255 lph walbro,
73 turbo pinto panel wagon, ms1, 85 lb inj, fmic, holset hy35, 3" exhaust, msd, bov,

dianne

I got all that for 2.3 EFI I'm putting in. It has everything mostly including the computer and wiring harnesses. I was lucky as this guy saved them all.

Those can be pulled out of pretty much any fox body, can't they?
Vehicles:

- 1972 Plymouth Duster (To be a Pro Street)
- 1973 Ford Pinto wagon (registered ride 195)
- 1976 Mustang II mini-stock
- 1978 Mustang King Cobra II
- 1979 Ford Pinto Runabout
- 1986 Chevy K5 Blazer
- 1997 Suzuki Marauder

FORD: Federal Ownership Respectfully Denied

amc49

OP's original premise................

' my question is what does that engine need to see to run? id like to keep the fuel injection if possible but what does the ecm look at to make that engine run? if I can figure that out then I can go through the rest of the wiring harness and get rid of unneeded wires.'

You are assuming OP has the complete wiring harness, say it. He seems to say he doesn't, worlds apart there.

Highly over simplified and how people get into big trouble to begin with. Leave anything in that .pdf out and you will be pretty much walking.................and why on earth would someone not hook up check engine light wire, self inflicted pain of the highest order and not smart at all. The O2 has a heater as well-one wire only wastes lots of fuel in prolonged open loop.


pintoguy76

I'm telling you there are only a few wires on that engine that need to be connected. Believe me, I've done it. The 91 2.3 uses an integrated relay module that basically has one power wire that runs to it, and one to the computer.... then one to heated oxygen sensor. A few grounds, the fuel pump, a hot-in-run to the ignition and i believe that is it....it was not hard.


Most of the wires you see in that diagram run between the sensors/engine controls and the computer. Only a handful actually go outside of the harness. There were only three connectors (each with a few wires that connected elsewhere in the car) that had to be disconnected from the donor car to remove the harness from the car itself. Some of those wires aren't even needed... such as the check engine light wire and the wire for the tachometer signal. Most people don't even hook those up. There are a few others that aren't needed too. I weeded those out......
1974 Ford Pinto Wagon with 1991 Mustang DIS EFI 2.3 and stock Pinto 4 Speed

1996 Chevy C2500 Suburban with 6.5L Turbo Diesel/4L80E 4x2

1980 Volvo 265 with 1997 S-10 4.3 and a modified 700R4

2010 GMC Sierra SLE 1500 4x2 5.3 6L80E

amc49

Engine will need every single thing shown in that .pdf other than possibly the A4LD if you are running manual trans. Have fun wiring that IRCM module up. It controls fuel pump, a/c, and rad fan among other things. FYI fuel pump is inside fuel tank. Others here have gotten around that before.

You CAN do this, but absolutely not 6 wires only as said there. Engine needs every sensor in there, PCM will post codes and not run right if you dump any of them.

dillonwilkinson

That's what I planned on doing. Then just weeding out what wires I don't need from the harness. That's why I was wondering what all the engine needs to run ( sensor wise)

amc49

LOL, I'd like to see someone wire that up using only 6 wires. The injectors alone need five and they won't work without all the other sensors wired in as well. Way more than six wires if you look at that schematic. Easiest way is using the wiring harness and PCM that comes with the engine.

dillonwilkinson

Thank you for the link oldkayaker. And for pintoguy76 I would love some help I would really appreciate that. I didn't think it would be too hard that's not that new of an engine I just don't know those engines like you guys do. How do you like having that engine in your car? How's the power and fuel economy?

pintoguy76

If you want I can help you wire up the fuel injection for the  91 2.3. Its not as hard as some people make it sound, in fact its really quite simple. A half dozen or so wires at most.....I put that same engine into my 74 pinto. I got it wired right the first time, it started right up. Didnt have to redo it or anything. It runs like a dream...I even wired up the check engine light and the vehicle speed sensor....

My engine is the exact same thing you are talking about - 1991 Mustang 2.3 Distributorless Ignition with 8 spark plugs.
1974 Ford Pinto Wagon with 1991 Mustang DIS EFI 2.3 and stock Pinto 4 Speed

1996 Chevy C2500 Suburban with 6.5L Turbo Diesel/4L80E 4x2

1980 Volvo 265 with 1997 S-10 4.3 and a modified 700R4

2010 GMC Sierra SLE 1500 4x2 5.3 6L80E

oldkayaker

Below is a link to a 1991 Mustang wiring diagram for the 2.3 engine.
http://www.rothfam.com/svo/reference/90-91Mustang.pdf
Jerry J - Jupiter, Florida

amc49

You will NOT be removing wires, rather installing them, a lot in fact.

dillonwilkinson

I'm new here and I've read a few things on this page and it seems like the people on here are pretty knowledgeable so here we go. I have a 48 willy's jeep that currently has a carbureted 302 in it. the engine swap was done when I got it and it was really cool for a while until I snapped the frame. I found a new frame and always told myself that when I get to the point of putting the new frame in it that I would get rid of the 302 and go with something a little smaller. after doing some research I found a company that has a full adapter setup to drop a 2.3l in a jeep like mine. I have a friend with a 91 mustang that has a fuel injected 2.3l in it but I don't know much about them (this one has the dual spark plug setup). my question is what does that engine need to see to run? id like to keep the fuel injection if possible but what does the ecm look at to make that engine run? if I can figure that out then I can go through the rest of the wiring harness and get rid of unneeded wires. if this just seems un-doable then how could you convert that engine to carbureted? I've seen different intake manifolds for those so a guy can bolt on a carburetor but if you do that then what do you do about the fuel injector holes in the head?