Mini Classifieds

Front Body parts needed
Date: 02/09/2018 06:09 pm
1970-1973 British 4 Speed Manual; Parts or Whole
Date: 03/17/2019 03:57 am
4 speed pinto transmission

Date: 05/13/2021 05:29 pm
2.3 bellhousing stick
Date: 07/24/2019 06:50 pm
1976 Ford Pinto Wagon - just rebuilt. 302 v8

Date: 11/11/2019 03:38 pm
hubcaps

Date: 10/31/2018 12:04 pm
'79 Ford Pinto, Green,

Date: 10/29/2019 11:50 am
Plug Or Cover For Hatch Hinge Bolt For 1979
Date: 05/28/2017 03:20 pm
Need right door for pinto or bobcat 1977 to 1980 station wagon
Date: 08/03/2018 09:19 am

Why the Ford Pinto didn’t suck

Why the Ford Pinto didn't suckThe Ford Pinto was born a low-rent, stumpy thing in Dearborn 40 years ago and grew to become one of the most infamous cars in history. The thing is that it didn't actually suck. Really.

Even after four decades, what's the first thing that comes to mind when most people think of the Ford Pinto? Ka-BLAM! The truth is the Pinto was more than that — and this is the story of how the exploding Pinto became a pre-apocalyptic narrative, how the myth was exposed, and why you should race one.

The Pinto was CEO Lee Iacocca's baby, a homegrown answer to the threat of compact-sized economy cars from Japan and Germany, the sales of which had grown significantly throughout the 1960s. Iacocca demanded the Pinto cost under $2,000, and weigh under 2,000 pounds. It was an all-hands-on-deck project, and Ford got it done in 25 months from concept to production.

Building its own small car meant Ford's buyers wouldn't have to hew to the Japanese government's size-tamping regulations; Ford would have the freedom to choose its own exterior dimensions and engine sizes based on market needs (as did Chevy with the Vega and AMC with the Gremlin). And people cold dug it.

When it was unveiled in late 1970 (ominously on September 11), US buyers noted the Pinto's pleasant shape — bringing to mind a certain tailless amphibian — and interior layout hinting at a hipster's sunken living room. Some call it one of the ugliest cars ever made, but like fans of Mischa Barton, Pinto lovers care not what others think. With its strong Kent OHV four (a distant cousin of the Lotus TwinCam), the Pinto could at least keep up with its peers, despite its drum brakes and as long as one looked past its Russian-roulette build quality.

But what of the elephant in the Pinto's room? Yes, the whole blowing-up-on-rear-end-impact thing. It all started a little more than a year after the Pinto's arrival.

 

Grimshaw v. Ford Motor Company

On May 28, 1972, Mrs. Lilly Gray and 13-year-old passenger Richard Grimshaw, set out from Anaheim, California toward Barstow in Gray's six-month-old Ford Pinto. Gray had been having trouble with the car since new, returning it to the dealer several times for stalling. After stopping in San Bernardino for gasoline, Gray got back on I-15 and accelerated to around 65 mph. Approaching traffic congestion, she moved from the left lane to the middle lane, where the car suddenly stalled and came to a stop. A 1962 Ford Galaxie, the driver unable to stop or swerve in time, rear-ended the Pinto. The Pinto's gas tank was driven forward, and punctured on the bolts of the differential housing.

As the rear wheel well sections separated from the floor pan, a full tank of fuel sprayed straight into the passenger compartment, which was engulfed in flames. Gray later died from congestive heart failure, a direct result of being nearly incinerated, while Grimshaw was burned severely and left permanently disfigured. Grimshaw and the Gray family sued Ford Motor Company (among others), and after a six-month jury trial, verdicts were returned against Ford Motor Company. Ford did not contest amount of compensatory damages awarded to Grimshaw and the Gray family, and a jury awarded the plaintiffs $125 million, which the judge in the case subsequently reduced to the low seven figures. Other crashes and other lawsuits followed.

Why the Ford Pinto didn't suck

Mother Jones and Pinto Madness

In 1977, Mark Dowie, business manager of Mother Jones magazine published an article on the Pinto's "exploding gas tanks." It's the same article in which we first heard the chilling phrase, "How much does Ford think your life is worth?" Dowie had spent days sorting through filing cabinets at the Department of Transportation, examining paperwork Ford had produced as part of a lobbying effort to defeat a federal rear-end collision standard. That's where Dowie uncovered an innocuous-looking memo entitled "Fatalities Associated with Crash-Induced Fuel Leakage and Fires."

The Car Talk blog describes why the memo proved so damning.

In it, Ford's director of auto safety estimated that equipping the Pinto with [an] $11 part would prevent 180 burn deaths, 180 serious burn injuries and 2,100 burned cars, for a total cost of $137 million. Paying out $200,000 per death, $67,000 per injury and $700 per vehicle would cost only $49.15 million.

The government would, in 1978, demand Ford recall the million or so Pintos on the road to deal with the potential for gas-tank punctures. That "smoking gun" memo would become a symbol for corporate callousness and indifference to human life, haunting Ford (and other automakers) for decades. But despite the memo's cold calculations, was Ford characterized fairly as the Kevorkian of automakers?

Perhaps not. In 1991, A Rutgers Law Journal report [PDF] showed the total number of Pinto fires, out of 2 million cars and 10 years of production, stalled at 27. It was no more than any other vehicle, averaged out, and certainly not the thousand or more suggested by Mother Jones.

Why the Ford Pinto didn't suck

The big rebuttal, and vindication?

But what of the so-called "smoking gun" memo Dowie had unearthed? Surely Ford, and Lee Iacocca himself, were part of a ruthless establishment who didn't care if its customers lived or died, right? Well, not really. Remember that the memo was a lobbying document whose audience was intended to be the NHTSA. The memo didn't refer to Pintos, or even Ford products, specifically, but American cars in general. It also considered rollovers not rear-end collisions. And that chilling assignment of value to a human life? Indeed, it was federal regulators who often considered that startling concept in their own deliberations. The value figure used in Ford's memo was the same one regulators had themselves set forth.

In fact, measured by occupant fatalities per million cars in use during 1975 and 1976, the Pinto's safety record compared favorably to other subcompacts like the AMC Gremlin, Chevy Vega, Toyota Corolla and VW Beetle.

And what of Mother Jones' Dowie? As the Car Talk blog points out, Dowie now calls the Pinto, "a fabulous vehicle that got great gas mileage," if not for that one flaw: The legendary "$11 part."

Why the Ford Pinto didn't suck

Pinto Racing Doesn't Suck

Back in 1974, Car and Driver magazine created a Pinto for racing, an exercise to prove brains and common sense were more important than an unlimited budget and superstar power. As Patrick Bedard wrote in the March, 1975 issue of Car and Driver, "It's a great car to drive, this Pinto," referring to the racer the magazine prepared for the Goodrich Radial Challenge, an IMSA-sanctioned road racing series for small sedans.

Why'd they pick a Pinto over, say, a BMW 2002 or AMC Gremlin? Current owner of the prepped Pinto, Fox Motorsports says it was a matter of comparing the car's frontal area, weight, piston displacement, handling, wheel width, and horsepower to other cars of the day that would meet the entry criteria. (Racers like Jerry Walsh had by then already been fielding Pintos in IMSA's "Baby Grand" class.)

Bedard, along with Ron Nash and company procured a 30,000-mile 1972 Pinto two-door to transform. In addition to safety, chassis and differential mods, the team traded a 200-pound IMSA weight penalty for the power gain of Ford's 2.3-liter engine, which Bedard said "tipped the scales" in the Pinto's favor. But according to Bedard, it sounds like the real advantage was in the turns, thanks to some add-ons from Mssrs. Koni and Bilstein.

"The Pinto's advantage was cornering ability," Bedard wrote. "I don't think there was another car in the B. F. Goodrich series that was quicker through the turns on a dry track. The steering is light and quick, and the suspension is direct and predictable in a way that street cars never can be. It never darts over bumps, the axle is perfectly controlled and the suspension doesn't bottom."

Need more proof of the Pinto's lack of suck? Check out the SCCA Washington, DC region's spec-Pinto series.

Members
Stats
  • Total Posts: 139,575
  • Total Topics: 16,267
  • Online today: 2,670
  • Online ever: 2,670 (Today at 01:57:20 AM)
Users Online
  • Users: 0
  • Guests: 593
  • Total: 593
F&I...more

My Somewhat Begrudging Apology To Ford Pinto

ford-pinto.jpg

I never thought I’d offer an apology to the Ford Pinto, but I guess I owe it one.

I had a Pinto in the 1970s. Actually, my wife bought it a few months before we got married. The car became sort of a wedding dowry. So did the remaining 80% of the outstanding auto loan.

During a relatively brief ownership, the Pinto’s repair costs exceeded the original price of the car. It wasn’t a question of if it would fail, but when. And where. Sometimes, it simply wouldn’t start in the driveway. Other times, it would conk out at a busy intersection.

It ranks as the worst car I ever had. That was back when some auto makers made quality something like Job 100, certainly not Job 1.

Despite my bad Pinto experience, I suppose an apology is in order because of a recent blog I wrote. It centered on Toyota’s sudden-acceleration problems. But in discussing those, I invoked the memory of exploding Pintos, perpetuating an inaccuracy.

The widespread allegation was that, due to a design flaw, Pinto fuel tanks could readily blow up in rear-end collisions, setting the car and its occupants afire.

People started calling the Pinto “the barbecue that seats four.” And the lawsuits spread like wild fire.

Responding to my blog, a Ford (“I would very much prefer to keep my name out of print”) manager contacted me to set the record straight.

He says exploding Pintos were a myth that an investigation debunked nearly 20 years ago. He cites Gary Schwartz’ 1991 Rutgers Law Review paper that cut through the wild claims and examined what really happened.

Schwartz methodically determined the actual number of Pinto rear-end explosion deaths was not in the thousands, as commonly thought, but 27.

In 1975-76, the Pinto averaged 310 fatalities a year. But the similar-size Toyota Corolla averaged 313, the VW Beetle 374 and the Datsun 1200/210 came in at 405.

Yes, there were cases such as a Pinto exploding while parked on the shoulder of the road and hit from behind by a speeding pickup truck. But fiery rear-end collisions comprised only 0.6% of all fatalities back then, and the Pinto had a lower death rate in that category than the average compact or subcompact, Schwartz said after crunching the numbers. Nor was there anything about the Pinto’s rear-end design that made it particularly unsafe.

Not content to portray the Pinto as an incendiary device, ABC’s 20/20 decided to really heat things up in a 1978 broadcast containing “startling new developments.” ABC breathlessly reported that, not just Pintos, but fullsize Fords could blow up if hit from behind.

20/20 thereupon aired a video, shot by UCLA researchers, showing a Ford sedan getting rear-ended and bursting into flames. A couple of problems with that video:

One, it was shot 10 years earlier.

Two, the UCLA researchers had openly said in a published report that they intentionally rigged the vehicle with an explosive.

That’s because the test was to determine how a crash fire affected the car’s interior, not to show how easily Fords became fire balls. They said they had to use an accelerant because crash blazes on their own are so rare. They had tried to induce a vehicle fire in a crash without using an igniter, but failed.

ABC failed to mention any of that when correspondent Sylvia Chase reported on “Ford’s secret rear-end crash tests.”

We could forgive ABC for that botched reporting job. After all, it was 32 years ago. But a few weeks ago, ABC, in another one of its rigged auto exposes, showed video of a Toyota apparently accelerating on its own.

Turns out, the “runaway” vehicle had help from an associate professor. He built a gizmo with an on-off switch to provide acceleration on demand. Well, at least ABC didn’t show the Toyota slamming into a wall and bursting into flames.

In my blog, I also mentioned that Ford’s woes got worse in the 1970s with the supposed uncovering of an internal memo by a Ford attorney who allegedly calculated it would cost less to pay off wrongful-death suits than to redesign the Pinto.

It became known as the “Ford Pinto memo,” a smoking gun. But Schwartz looked into that, too. He reported the memo did not pertain to Pintos or any Ford products. Instead, it had to do with American vehicles in general.

It dealt with rollovers, not rear-end crashes. It did not address tort liability at all, let alone advocate it as a cheaper alternative to a redesign. It put a value to human life because federal regulators themselves did so.

The memo was meant for regulators’ eyes only. But it was off to the races after Mother Jones magazine got a hold of a copy and reported what wasn’t the case.

The exploding-Pinto myth lives on, largely because more Americans watch 20/20 than read the Rutgers Law Review. One wonders what people will recollect in 2040 about Toyota’s sudden accelerations, which more and more look like driver error and, in some cases, driver shams.

So I guess I owe the Pinto an apology. But it’s half-hearted, because my Pinto gave me much grief, even though, as the Ford manager notes, “it was a cheap car, built long ago and lots of things have changed, almost all for the better.”

Here goes: If I said anything that offended you, Pinto, I’m sorry. And thanks for not blowing up on me.

a couple of tips from experience

Started by jonz2pinto, October 04, 2014, 02:27:36 PM

Previous topic - Next topic

0 Members and 1 Guest are viewing this topic.

amc49

Splash only CAN keep an engine together but only if the oil can get flung where it needs, engines are a lot more convoluted inside than back then and usually double the number of parts to splash. Let just one bearing not get enough oil and kiss that sucker goodbye and I don't care which engineer says otherwise. You can scratch a bearing enough to ruin it with your fingernail and no effort at all. Tell them to use a modern engine for a splash test instead of an old one that had few parts to lube and I might listen. Self fulfilling story if you ask me.

Do some reading on the difference in oil pressure requirements from roller type bearings as vs. plain type and tell me you don't need that oil wedge, pretty funny. Rollers can run at 10 psi and 10,000 rpm, try running plain bearing at that and see what happens, that's more pressure than splash gives and you'll tear it up in less than five minutes. The old engine used much bigger bearing area, now the smaller bearing is normal loaded harder and not the same AT ALL. Modern plain type bearings MUST have that pressure to survive. The pressure provides the flow amount.

Can't splash anyway, the surest way to kill 10-15% or more mileage. Just unwrapping the crankshaft of oil trapped in it at high rpm is worth 50 hp on V8 dry sump cars and why they do it.

Look at how they all have anti-drainback filters now, either learn from that or not. There's a reason why all OEMs have gone there and it's not that the oil stays in the bearings better, it's that it drains out faster when thinner.  Hot OR cold. Capillary attraction that sticks oil in place around clearances drops off with thinner liquid used. Study how viscosity is measured, it indirectly but solidly relates to that very issue. AND, if cold starts are so evil and bad, then why can you not think of one car you had that was damaged by that using oldschool oil? It just didn't happen. And no start up rattle back then like now either.  I have none at all and never have. Even on 200K mile cars.  After having disassembled like hundreds of motors you also come to the conclusion they still pretty much kept old school oil around the bearings for long periods of time, the oil passages are still full even after years if filter left on and bearings will still have oil in them as well. Much of that dry start stuff is crap myth.

Beware the stuff you read at BITOG, some of those engineers are quacks, I ran into them when Dad's friends from LTV Aeronautical used to come into the shop, some of those guys had degrees nine miles long but were absolute and total nutjobs. I used to wonder how they could get planes in the air with some of that thinking. Some of it was just screwy.

dick1172762

This is more or less what Bob the oil guy says on his web site. He is really pushing the use of thinner oil to take less time for the oil to reach the bearings. He has also stated that oil pressure is really vodo and that all you really need is enough to keep the lifters pumped up. He had a great post about Hudson in the 30's that ran very good with NO oil pump. Just splash to keep the engine lubed. He stated that the oil is there to carry the heat off, not make the crank float with out touch the bearings. Good reading.
Its better to be a has-been, than a never was.

amc49

The newer cars use lighter weight oils for one reason only.............mileage. You save maybe $7 a year in fuel cost, at least what I figured once at around 15K miles a year. In my view the other reason is because the oils wear the engines slightly faster-they are trying to make up for cars lasting too long now. They did their job too well for once, the PCM keeps them running forever now. Take note of how much talk now about 'startup rattle' like it's been there forever but it hasn't, only since the oils got so light. I have actually cured that rattle by going to higher vis oil and forget the $7. You never really heard of anti-drainback valves in filters until the thinner oils showed up, even though several engines used them WAY back. Now everything pretty much does.

The conventional wisdom says thicker oil is harder to pump up when cold. True.........BUTTT..........

Thinner oil can run out of the bearing clearances easier when capillary attraction quits easier, a function of all fluids in relation to viscosity. Funny how they never tell you that part in the ads..........if the oil is thicker it hasn't backdrained out of the bearings..............

The friction modifiers they replaced the zinc with work pretty well on older stuff unless you start running killer valvetrain loads like on oldschool cam rubbing surfaces. You can find more expensive motorcycle specialty oils that still have zinc but you pay a premium for it now. Truck oils like Delo and Rotella have pretty much lost their extra zinc as well now too.

Certain types of motorcycle have one way clutch type starting systems that if you use a modern car oil with no zinc can then begin to slip to not start, the friction modifiers work that well. TOO well. Changing to correct oil then puts the starter back right again.

Myself, I still use 10-30 or 10-40 oils and will go no lighter, or my old stand by straight 30 weight. Got it in like 3 cars right now and can't kill them. I'd go straight 40 here in Texas in the summer if it wasn't so expensive now. Conventional oil, not synthetic, I haven't gone there yet. At around 9000 mile oil change intervals now I make money even with the oil changes. Can't put my fingers on it exactly but some of the mods they've made to oil in the last few years have also transferred to the conventional oils as well in my view, they won't tell you that of course because they want you to justify all that investment by buying synthetic. I'm beginning to think some of that friction-modifier-zinc-replacement technology IS synthetic and they have to put it in everything but don't say. The oils just don't burn black nearly as quickly as they used to and I'm talking still in the realm of recent PCM controlled cars, not the old carbed ones. At the 9000 number I quoted above the oil will still be brown not nearly black and be still about 80% transparent with very little opacity. Why I started stretching the oil changes further and further, an experiment. I had been running 6000 for many years. Pulled pan on one @ 150K, NO sludge in bottom, I'm talking NONE, light film only that rinsed right off. WALMART Supertech straight 30 weight! Crap oil!

Not saying you all should go and do this but there's food for thought in there somewhere............the fed regulations that oil makers dump zinc and increase mileage may have brought on much better product overall, even the cheap crap.

sedandelivery

Thank you for the replies. I was wondering as all the newer cars use very light weight oils and I know the older engines use higher viscosity oils, and the discussion of lack of zinc in the newer oils had me wondering.

65ShelbyClone

I completely quit patronizing British Petroleum (owner of Castrol oil and Arco gas) in response to their (mis)handling of the gulf oil disaster.

Quote from: sedandelivery on October 20, 2014, 06:22:58 AM
Any recommendations of the best kind of oil to buy for old engines?

Just about anything of the right viscosity these days. I have a conglomeration of oils in my turbo engine right now because it's what I had for the initial prime and start. No-name 20w-50, Chevron Delo 400, Chevron Supreme 10w-30/10w-40, and I think there's some Shell in there too. Conventional oils have been suitable for most applications for a few decades.

Ford's 2.3 went roller cam in '88-89. Toyota stuck with their slider 8v for seven more years. Nissan went to buckets somewhere in the middle, but none of the Japanese engines are known for wiping-out cams. I don't think Fords actually are either.
'72 Runabout - 2.3T, T5, MegaSquirt-II, 8", 5-lugs, big brakes.
'68 Mustang - Built roller 302, Toploader, 9", etc.

74 PintoWagon

Been using off the shelf Castrol GTX for a long time, my 73 dually had 150,000 on the motor when I yanked it out to sell the truck, motor still runs like a top..
Art
65 Falcon 2DR 200 IL6 with C4.

sedandelivery

Any recommendations of the best kind of oil to buy for old engines? Besides the Pinto I have to work on a 1974 Chevrolet Dump Truck .

amc49

The newer engines are commonly four valve with springs so weak you can easily push them by hand. No big amount of zinc needed there. Nothing like the big wipe of a 2.3 follower as valve opens..............they often chewed up even back in the day.

65ShelbyClone

It's true that oil formulations have changed, but tons of new engines still have sliding cam followers. Old flat-tappet pushrod engines are especially susceptible to "energy conserving" oils with low ZDDP levels, but those same oils are specified and fine for many OHC engines that don't have roller valvetrain.
'72 Runabout - 2.3T, T5, MegaSquirt-II, 8", 5-lugs, big brakes.
'68 Mustang - Built roller 302, Toploader, 9", etc.

fozzy

One thing to also consider these days is that engine oil has changed over the last bunch of years. The new oils are designed for newer engines with roller cams and don't have the same additives as oils from yesteryear.
Engine oils like Joe Gibbs racing oil or oils fortified with ZDDP are more suited to engines with flat tappet rockers etc.

jonz2pinto

 :D if you change instrument cluster or any part of it be careful.not all are the same.example I had one that the white plastic everything mounted to crumbled into dust.I put one from a different year(looked the same)but the alt and engine lights were reversed.I chased an alt light and could not figure it out.it ended up I was low on oil(enough to starve rod bearings til one started to knock).I recently changed to full synthetic oil and it started to leak when previous I had no problem. it was a 76 2.8 v6.also it may not make sense but if you run one brand of oil and change you may experience some wear issues.case in point-2.0 rebuilt,no ticking from rockers when running Castro oil.oil was changed to quaker state by an oil change place.then the cam and rockers got completely wiped out in less than  1,000 miles.motor was broke in just fine.can and rockers replaced,changed back to Castro and no more problems.different oil blends affect metallergy in my thinking.changing oil brands other times caused similar problems. Also if you have solid rockers that were never adjusted or had been a long time there may be build up on rocker tips.it may take a couple of times adjusting them to get them from ticking.I had to on a 2.8v6.someone gave me that tip.
Pinto-is short for pint-o-fun.