Current Classifieds

1977 Pinto Cruising Wagon FOR SALE

Date: 08/20/2017 01:34 pm
78 windshield trim
Date: 02/01/2020 08:46 am
1977 pinto rear bumper
Date: 04/19/2021 11:57 am
1973 Pinto Runabout

Date: 03/25/2019 09:02 pm
Seeking reveal molding for driver's door for a 1980 Squire Wagon
Date: 11/08/2020 02:10 pm
1980 PINTO for sale
Date: 06/19/2017 02:51 pm
SVO SWAP
Date: 03/15/2018 03:12 am
Needed- Good 71-73 Rear End or parts- close to AL
Date: 09/15/2019 12:38 pm
1972 Runabout 351 Cleveland V8

Date: 11/05/2016 09:03 pm
Need 2.3 timing cover
Date: 08/10/2018 11:41 am
turbo 4 cyl and aod trans
Date: 12/14/2019 04:55 pm
Looking for Radiator and gas tank
Date: 10/24/2018 07:35 am

Author Topic: Anybody with a Chilton manual...  (Read 1226 times)

0 Members and 1 Guest are viewing this topic.

Offline jeremysdad

  • Pinto Sr. Member
  • ****
  • Posts: 405
  • FeedBack: +83/-6
  • Gender: Male
  • Restoring a Daily Driver

  • Total Badges: 4
    Badges: (View All)
    Fifth year Anniversary Topic Starter Poll Voter Windows User
Anybody with a Chilton manual...
« on: February 09, 2014, 01:09:07 PM »
What size drill bit does adjusting the neutral safety switch require?

Thanks in advance.

~jeremysdad

Offline Wittsend

  • Pinto Master
  • *****
  • Posts: 2499
  • FeedBack: +241/-0

  • Total Badges: 8
    Badges: (View All)
    Tenth year Anniversary Mobile User Topic Starter Poll Voter 1000 Posts Linux User Windows User Fifth year Anniversary
Re: Anybody with a Chilton manual...
« Reply #1 on: February 09, 2014, 04:13:13 PM »
It's a #43 (.089) drill bit. These are the closest fraction sizes:
too small 5/64 = .0781
too large 3/32 = .0938

Insert .484 depth (I'm sure 1/2" would be close enough)

Offline jeremysdad

  • Pinto Sr. Member
  • ****
  • Posts: 405
  • FeedBack: +83/-6
  • Gender: Male
  • Restoring a Daily Driver

  • Total Badges: 4
    Badges: (View All)
    Fifth year Anniversary Topic Starter Poll Voter Windows User
Re: Anybody with a Chilton manual...
« Reply #2 on: February 09, 2014, 05:03:04 PM »
Thank you!

I need to order another manual. :)

Offline jeremysdad

  • Pinto Sr. Member
  • ****
  • Posts: 405
  • FeedBack: +83/-6
  • Gender: Male
  • Restoring a Daily Driver

  • Total Badges: 4
    Badges: (View All)
    Fifth year Anniversary Topic Starter Poll Voter Windows User
Re: Anybody with a Chilton manual...
« Reply #3 on: February 09, 2014, 05:12:42 PM »
A 3D nail is .083"...numbered drill bit set is probably easier to find, either locally or online. :) lol

Offline amc49

  • PCCA VIP
  • Pinto Master
  • ***
  • Posts: 1256
  • FeedBack: +242/-1
  • Another Pinto Driver

  • Total Badges: 4
    Badges: (View All)
    Topic Starter Poll Voter Windows User 1000 Posts
Re: Anybody with a Chilton manual...
« Reply #4 on: February 10, 2014, 12:06:18 AM »
Yes, the #43 bit. Used on other cars too sometimes, I look for a hole that looks right to adjust and commonly the #43 fits it. Apparently they used it on more than one car.