Current Classifieds

LOOKING for INTERIOR PARTS, MIRRORS & A HOOD LATCH
Date: 04/06/2017 12:13 am
ISO instrument panel 80 hatchback
Date: 04/20/2017 08:56 pm
Early V8 swap headers, damaged, fixable?
Date: 10/25/2019 03:30 pm
74 Wagon Interior
Date: 01/22/2017 06:38 pm
WANTED: Dash, fender, hood, gauge bezel '73 Wagon
Date: 01/18/2017 05:35 pm
78 hatchback

Date: 03/12/2023 06:50 pm
Mustang II C4 Transmission
Date: 07/28/2017 06:26 am
72 PINTO WAGON

Date: 09/23/2018 06:16 pm
Wanted Pinto Fiberglass Body Parts
Date: 05/19/2018 04:56 pm
Holley 2305 progressive 2 bbl carb 350cfm

Date: 10/11/2019 11:13 am
Pinto wagon Parts
Date: 06/23/2021 03:25 pm
1980 Pinto Parts

Date: 08/05/2020 04:20 pm

« previous next »
Pages: [1]   Go Down

Author Topic: whois gonna build it.  (Read 1364 times)

0 Members and 1 Guest are viewing this topic.

Offline gt mayoh

  • Pinto Member
  • **
  • Posts: 32
  • FeedBack: +0/-2
  • Gender: Male
  • syco slidin a pinette

    • Total Badges: 1
    Badges: (View All)
    Topic Starter
whois gonna build it.
« on: May 15, 2013, 10:35:23 AM »
o.k. here's a idea that's been in my head for a decade.I dont normally give away ideas chances are i'm not  and would like to see it. drum roll pinto sho the sho v6 is the vulcan bolt patten which is the same as ran/mustang/pinto 2.8 .i have all ready  did this build in a 94 mazda 3000 with a 96 sho engine 
Logged

Offline D.R.Ball

  • Pinto Sr. Member
  • ****
  • Posts: 558
  • FeedBack: +36/-2
  • Gender: Male

    • Total Badges: 5
    Badges: (View All)
    Topic Starter Tenth year Anniversary Poll Voter Windows User Fifth year Anniversary
Re: whois gonna build it.
« Reply #1 on: May 15, 2013, 08:16:12 PM »
Sounds great, but it's been done in XR4ti so it should not be too much of a hassle . You do realize that parts to get the rebuild done are pricey. And the timing belt etc. must be done when at 100,000 miles. Is the engine an interference design ? So if the timing belt goes so does the engine....
Logged

Offline gt mayoh

  • Pinto Member
  • **
  • Posts: 32
  • FeedBack: +0/-2
  • Gender: Male
  • syco slidin a pinette

    • Total Badges: 1
    Badges: (View All)
    Topic Starter
Re: whois gonna build it.
« Reply #2 on: May 16, 2013, 01:41:34 PM »
its not a turbo 4 its a ford/yamaha/mercury marine joit on a 3litre v6 normally aspirated and was only available in one model world wide and that was the taurus.they did prototype a ranger p/u in witch i duplicated but in a 94 body not the 89 body ford had used. the truck was seriously fast quiet a sleeper as a pinto it would be over the top
Logged

Offline Stubby350

  • Pinto Member
  • **
  • Posts: 15
  • FeedBack: +0/-0
  • Another Pinto Driver

    • Total Badges: 2
    Badges: (View All)
    Topic Starter Windows User
Re: whois gonna build it.
« Reply #3 on: May 27, 2013, 08:33:28 PM »
Sounds like a fun project and scalded dog fast... Looking forward to seeing this...
Logged
Pages: [1]   Go Up
« previous next »