Current Classifieds

oldskool787
Date: 02/12/2017 12:42 pm
Squire trim
Date: 03/28/2018 10:11 am
Tubing bender 1/2 to 2 1/2 (3) inch roll cage / mufflers and more

Date: 03/13/2021 12:57 pm
parting out 1975 & 80 pintos
Date: 04/28/2018 04:12 pm
99' 2.5l lima cylinder head

Date: 01/13/2017 01:56 am
Want seals for Pinto wagon "flip out" windows
Date: 08/08/2017 01:44 pm
Pinto 4-spd transmissions
Date: 06/15/2018 09:15 am
Holley 4bbl carb. & Offenhauser intake.

Date: 08/09/2018 07:49 am
Pinto Fiber Glass Body Parts
Date: 01/06/2019 06:53 pm
V8 rear end
Date: 04/12/2018 10:57 am
71-73 Front Kick Panels
Date: 04/25/2021 07:24 pm
Front sway bar frame brackets
Date: 07/13/2017 01:05 am

Author Topic: whois gonna build it.  (Read 1189 times)

0 Members and 1 Guest are viewing this topic.

Offline gt mayoh

  • Pinto Member
  • **
  • Posts: 32
  • FeedBack: +0/-2
  • Gender: Male
  • syco slidin a pinette

  • Total Badges: 1
    Badges: (View All)
    Topic Starter
whois gonna build it.
« on: May 15, 2013, 10:35:23 AM »
o.k. here's a idea that's been in my head for a decade.I dont normally give away ideas chances are i'm not  and would like to see it. drum roll pinto sho the sho v6 is the vulcan bolt patten which is the same as ran/mustang/pinto 2.8 .i have all ready  did this build in a 94 mazda 3000 with a 96 sho engine 

Offline D.R.Ball

  • Pinto Sr. Member
  • ****
  • Posts: 558
  • FeedBack: +36/-2
  • Gender: Male

  • Total Badges: 5
    Badges: (View All)
    Topic Starter Tenth year Anniversary Poll Voter Windows User Fifth year Anniversary
Re: whois gonna build it.
« Reply #1 on: May 15, 2013, 08:16:12 PM »
Sounds great, but it's been done in XR4ti so it should not be too much of a hassle . You do realize that parts to get the rebuild done are pricey. And the timing belt etc. must be done when at 100,000 miles. Is the engine an interference design ? So if the timing belt goes so does the engine....

Offline gt mayoh

  • Pinto Member
  • **
  • Posts: 32
  • FeedBack: +0/-2
  • Gender: Male
  • syco slidin a pinette

  • Total Badges: 1
    Badges: (View All)
    Topic Starter
Re: whois gonna build it.
« Reply #2 on: May 16, 2013, 01:41:34 PM »
its not a turbo 4 its a ford/yamaha/mercury marine joit on a 3litre v6 normally aspirated and was only available in one model world wide and that was the taurus.they did prototype a ranger p/u in witch i duplicated but in a 94 body not the 89 body ford had used. the truck was seriously fast quiet a sleeper as a pinto it would be over the top

Offline Stubby350

  • Pinto Member
  • **
  • Posts: 15
  • FeedBack: +0/-0
  • Another Pinto Driver

  • Total Badges: 2
    Badges: (View All)
    Topic Starter Windows User
Re: whois gonna build it.
« Reply #3 on: May 27, 2013, 08:33:28 PM »
Sounds like a fun project and scalded dog fast... Looking forward to seeing this...