Current Classifieds

Pinto Vinyl Top

Date: 10/09/2020 10:29 pm
Pinto brake booster needed
Date: 05/08/2021 09:00 am
McLeod Clutch

Date: 04/12/2017 12:08 pm
Wanted: automatic transmission shifter
Date: 07/21/2017 11:49 am
WTB: Ford Type 9 5spd Transmission
Date: 03/18/2020 01:30 am
1971 2.0 valve cover
Date: 01/25/2019 07:09 pm
Pinto Watch
Date: 06/22/2019 07:16 pm
Weiand Single plane manifold - for 72 Pinto 4 barrel Carb
Date: 04/25/2017 12:17 pm
Need hatchback fuel tank sending unit
Date: 08/13/2018 02:46 pm
1971 Pinto Do It Yourself Manual

Date: 03/06/2017 01:19 am
1979 Pinto Rear Bumper
Date: 03/26/2021 03:26 pm
WTB. Seat cover or material LFront
Date: 07/01/2019 03:17 pm

« previous next »
Pages: [1]   Go Down

Author Topic: Wagon Trailer Hitch  (Read 1229 times)

0 Members and 1 Guest are viewing this topic.

Offline flash041

  • PCCA VIP
  • Pinto Master
  • ***
  • Posts: 902
  • FeedBack: +88/-0
  • Gender: Male

    • Total Badges: 8
    Badges: (View All)
    Tenth year Anniversary Topic Starter Signature Poll Voter Windows User Linux User Mobile User Fifth year Anniversary
Wagon Trailer Hitch
« on: June 16, 2018, 03:33:19 PM »
I recently purchased a camper.  My old-home made hitch was strong enough, but i need to have the ball higher for the camper to tow level. I was going to fab a receiver hitch from scratch, but thought Id check to see if I could find a new one that would fit with few modifications. After searching online I settled for Curt number 11485, that fits a 2017 Mercedes-Benz C300. I contacted Curt for dimensions, and was confident that it would work.
Logged
1978 Pinto Cruising wagon (I am the original owner ! ) Built Aug 15th 1977 in NJ
1993 Mustang LX 2.3 convertible

Offline flash041

  • PCCA VIP
  • Pinto Master
  • ***
  • Posts: 902
  • FeedBack: +88/-0
  • Gender: Male

    • Total Badges: 8
    Badges: (View All)
    Tenth year Anniversary Topic Starter Signature Poll Voter Windows User Linux User Mobile User Fifth year Anniversary
Re: Wagon Trailer Hitch
« Reply #1 on: June 16, 2018, 03:36:47 PM »
I cut the outer corners as shown. On the right side I shaped one of the pieces I cut off and welded it in the gap that needed to be filled.
Logged
1978 Pinto Cruising wagon (I am the original owner ! ) Built Aug 15th 1977 in NJ
1993 Mustang LX 2.3 convertible

Offline flash041

  • PCCA VIP
  • Pinto Master
  • ***
  • Posts: 902
  • FeedBack: +88/-0
  • Gender: Male

    • Total Badges: 8
    Badges: (View All)
    Tenth year Anniversary Topic Starter Signature Poll Voter Windows User Linux User Mobile User Fifth year Anniversary
Re: Wagon Trailer Hitch
« Reply #2 on: June 16, 2018, 03:41:27 PM »
With the bumper on , I put the itch in place and marked the mounting holes that needed to be drilled. I removed the bumper and drilled the mounting holes.
Logged
1978 Pinto Cruising wagon (I am the original owner ! ) Built Aug 15th 1977 in NJ
1993 Mustang LX 2.3 convertible

Offline flash041

  • PCCA VIP
  • Pinto Master
  • ***
  • Posts: 902
  • FeedBack: +88/-0
  • Gender: Male

    • Total Badges: 8
    Badges: (View All)
    Tenth year Anniversary Topic Starter Signature Poll Voter Windows User Linux User Mobile User Fifth year Anniversary
Re: Wagon Trailer Hitch
« Reply #3 on: June 16, 2018, 03:49:22 PM »
I reinstalled the bumper. Support is needed at the bumper. I decided to use 5 inch long grade 8 bolts instead of welding on the receiver tube. I fabed two plates to keep the bolts together and used hardened washers for spacers. Supporting here is important, other wise the hitch would bend down under load. 

Logged
1978 Pinto Cruising wagon (I am the original owner ! ) Built Aug 15th 1977 in NJ
1993 Mustang LX 2.3 convertible

Offline flash041

  • PCCA VIP
  • Pinto Master
  • ***
  • Posts: 902
  • FeedBack: +88/-0
  • Gender: Male

    • Total Badges: 8
    Badges: (View All)
    Tenth year Anniversary Topic Starter Signature Poll Voter Windows User Linux User Mobile User Fifth year Anniversary
Re: Wagon Trailer Hitch
« Reply #4 on: June 16, 2018, 03:54:23 PM »
Once it was done I used a 5 inch ball mount riser to attain the proper height. I also added a seven Pin RV plug and brake controller. The hitch fits Perfectly! Just like it was make for it!
Logged
1978 Pinto Cruising wagon (I am the original owner ! ) Built Aug 15th 1977 in NJ
1993 Mustang LX 2.3 convertible
Pages: [1]   Go Up
« previous next »