Current Classifieds

Seeking reveal molding for driver's door for a 1980 Squire Wagon
Date: 11/08/2020 02:10 pm
Crane Cam
Date: 02/26/2018 07:50 am
1971 Pinto Do It Yourself Manual

Date: 03/06/2017 01:19 am
Need lower control arms for 1973 pinto
Date: 02/27/2017 10:10 pm
Wanted: Oil Breather F0ZZ6A485A "87-8 from 2.3L Turbo
Date: 08/06/2021 02:23 pm
71-71 speedo cable
Date: 07/31/2021 09:04 pm
Bumper Guards
Date: 03/28/2017 09:27 pm
'78 Pinto Windshield Trim
Date: 05/09/2017 10:46 am
74 Wagon Interior
Date: 01/22/2017 06:38 pm
Seeking 1971-1973 Rotors
Date: 04/08/2021 12:23 pm
Hoard of Pinto parts
Date: 12/17/2016 04:14 pm
75 wagon need parts
Date: 05/28/2020 05:19 pm

« previous next »
Pages: [1]   Go Down

Author Topic: Wagon Rear Shocks  (Read 915 times)

0 Members and 1 Guest are viewing this topic.

Offline flash041

  • PCCA VIP
  • Pinto Master
  • ***
  • Posts: 902
  • FeedBack: +88/-0
  • Gender: Male

    • Total Badges: 8
    Badges: (View All)
    Tenth year Anniversary Topic Starter Signature Poll Voter Windows User Linux User Mobile User Fifth year Anniversary
Wagon Rear Shocks
« on: October 03, 2018, 09:40:20 PM »
I was in need of new rear shocks for my 78 wagon. As you may know they are not available any more. I tried to find something close, with the same mountings. I found late 70's Camaro's rear shocks have the same mounts, but about 2 1/2 inches longer. I measured about 7 inches to the axle bump stop with suspension at rest hanging. The shocks have 8.25 inches of travel. the original shocks are about an inch short whit suspension at rest. So by my calculations the shock should bottom out about the same time as the bump stop. When installing them I attached the bottom first, then used a ratchet strap to pull and compress the shock into place. The part number for the coil-overs in Monroe #58551.
Logged
1978 Pinto Cruising wagon (I am the original owner ! ) Built Aug 15th 1977 in NJ
1993 Mustang LX 2.3 convertible

Offline Wittsend

  • Pinto Master
  • *****
  • Posts: 2498
  • FeedBack: +241/-0

    • Total Badges: 8
    Badges: (View All)
    Tenth year Anniversary Mobile User Topic Starter Poll Voter 1000 Posts Linux User Windows User Fifth year Anniversary
Re: Wagon Rear Shocks
« Reply #1 on: October 04, 2018, 10:29:12 AM »
Great information.


 I used regular (sedan) Pinto shocks on my wagon. Because the threaded portion is so long I was able to slide a thick wall tube over it. Ironically the early Pinto's have a similar pin type mount on the shock top as on the bottom, not the crossbar type in your picture. Lacking additional thick wall tubing I then stacked extra cupped washers on the top end to place the shock closer to its "travel range." So, either way the thick wall tubing, or stacked washers, you get the same results because the spacing places the shock very near its normal operating position. I was able to compensate for 1-1/2" of the 2" difference in the shocks. Note I did this to the "inside" sections.  6+ years and so far so good. But I do caution that one does this "at their own risk."
Logged
Pages: [1]   Go Up
« previous next »