Current Classifieds

1980 Pinto w/ Trunk
Date: 08/10/2022 04:09 pm
Bell housing
Date: 08/23/2017 05:41 am
2.8 Engine mount brackets
Date: 12/28/2016 11:42 am
NEED 77/78 MUSTANG II Left Motor Mount
Date: 04/15/2017 05:14 pm
Pinto Wheel Well Trim
Date: 03/29/2017 11:35 am
1973 Interior parts wanted
Date: 01/02/2017 11:02 pm
72 pinto drag car

Date: 07/08/2017 08:25 pm
72 Pinto parts
Date: 12/04/2018 09:56 pm
need a Ford battery for a 77 Pinto
Date: 02/21/2017 06:29 am
Offenhauser 6114 dp
Date: 09/12/2017 10:26 pm
1978 RUNABOUT

Date: 04/01/2017 03:18 pm
71,72 Pinto Door Panels

Date: 06/17/2018 08:27 pm

« previous next »
Pages: [1]   Go Down

Author Topic: mustang II console install questions  (Read 1504 times)

0 Members and 1 Guest are viewing this topic.

Offline shuffln

  • Pinto Member
  • **
  • Posts: 55
  • FeedBack: +7/-1
  • Another Pinto Driver

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Linux User Mobile User Windows User
mustang II console install questions
« on: October 25, 2015, 07:08:19 AM »
I know some have done this before any mods to make it fit? When i put it in my 79 it seems to slant towards drivers side
Logged

Offline russosborne

  • Pinto Master
  • *****
  • Posts: 2405
  • FeedBack: +47/-1
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 5
    Badges: (View All)
    Poll Voter Mobile User Topic Starter Signature 1000 Posts
Re: mustang II console install questions
« Reply #1 on: October 27, 2015, 07:26:39 PM »
How are you trying to mount the console?
Have you installed the brackets that go on the transmission hump for the console? If so, are they centered?. They aren't on a Pinto from the factory unless it came with that type of console, and I don't think any did.

If you just plop down the console without the brackets it is going to be up to you to get it positioned just right. It doesn't just fit on perfectly by itself.

Russ
Logged
In Glendale, Arizona

RIP Casey, Mallory, Abby, and Sadie. We miss you.

79 Pinto ESS fully caged fun car. In progress. 8inch 4.10 gears. 351C and a T5 waiting to go in.

Offline dave1987

  • Pinto Sr. Master
  • ******
  • Posts: 3431
  • FeedBack: +25/-0
  • Gender: Male

    • Total Badges: 11
    Badges: (View All)
    Topic Starter Signature Tenth year Anniversary Poll Voter Mobile User Apple User Linux User Windows User 1000 Posts Fifth year Anniversary Photographer
Re: mustang II console install questions
« Reply #2 on: November 07, 2015, 07:40:50 PM »
I have a full size MII console in my 78 Sedan. I didn't have any issues with it rolling to one side, but I did have issues with it being straight and level with the rest of the interior. For me, the important part of it was to have it down against the carpet, and flat/level, in the front passenger area. Mine sits about 1.5" above the carpet at the back end of the console, and I used some extra carpet and cardboard to make a "filler" section of carpet to fill in the gap between the carpet and the console. No one has noticed it yet.

Be sure you have the front bracket, and the rear one. The front bracket mounts under the dash at the front edge of the console, the rear bracket goes behind the e-brake handle, and the console is secured to the rear bracket at the rear most holes inside the arm rest compartment.
Logged
1978 Ford Pinto Sedan - Family owned since new

Remembering Jeff Fitcher with every drive in my 78 Sedan.

I am a Pinto Surgeon. Fixing problems and giving Pintos a chance to live again is more than a hobby, it's a passion!
Pages: [1]   Go Up
« previous next »