Current Classifieds

'76 Wagon Driver Side Rear Interior Panel
Date: 11/11/2019 04:49 pm
Pinto interior parts for Cruisen / Rallye wagon
Date: 01/19/2021 03:56 pm
Wiring diagram Ignition switch 72 2.0 4 speed pinto wagon
Date: 12/31/2017 11:14 pm
77 Cruising Wagon Front Seats
Date: 04/12/2017 12:37 pm
71/72 Pinto front end bushing kit
Date: 02/05/2017 09:45 am
NOS Sedan decklid

Date: 10/23/2019 11:51 am
74 hood
Date: 07/03/2017 03:46 pm
pinto floor mats??

Date: 01/11/2017 07:27 am
hood for a 79-80
Date: 11/30/2018 10:55 pm
2.3 carb intake

Date: 07/15/2020 09:25 pm
1978 hatch back

Date: 11/29/2019 03:18 pm
Need Mustang II Manual Transmission Mount
Date: 04/21/2017 02:03 pm

Author Topic: Hood latch restore?  (Read 1616 times)

0 Members and 1 Guest are viewing this topic.

Offline warhead2

  • Pinto Full Member
  • ***
  • Posts: 237
  • FeedBack: +4/-0
  • Gender: Male
  • 77 Crusin Wagon

  • Total Badges: 6
    Badges: (View All)
    Mobile User Topic Starter Poll Voter Windows User Tenth year Anniversary Fifth year Anniversary
Hood latch restore?
« on: May 12, 2017, 04:20:31 AM »
Has anyone rebuilt this part of the hood latch? Or can it be restored by removing the rivets and useing pop rivets to put back together? Mine is very rusty inside and would like to take apart clean and paint.

Sent from my SAMSUNG-SM-G930A using Tapatalk


Offline Wittsend

  • Pinto Master
  • *****
  • Posts: 2496
  • FeedBack: +241/-0

  • Total Badges: 8
    Badges: (View All)
    Tenth year Anniversary Mobile User Topic Starter Poll Voter 1000 Posts Linux User Windows User Fifth year Anniversary
Re: Hood latch restore?
« Reply #1 on: May 12, 2017, 11:56:42 AM »
There are a number of immersible products available that might preclude the disassembly of the latch.  Many are phosphoric acid based. Alternatively there is an electrical process using water, washing soda (sodium carbonate) a batter charger and a sacrificial piece of steel.  It is truly amazing to go back a few days later and see the rust transferred from the part to a piece of scrape steel.  Look it up there are articles all over the internet.  The first time I tried the process was on a very rusty file. Wire brushing it did little to get the rust out of the crevices and ran the risk of removing the sharp edges. The electrical process cleaned everything and retained the sharp edges. The image is of the file and transferred rust to a piece of angle iron. Obviously lubrication should be applied afterwards.

Disassembly would probably not profit much. The removal of the rivets can potential damage the housing and those are not generic pop rivets holding the piece together.

Offline warhead2

  • Pinto Full Member
  • ***
  • Posts: 237
  • FeedBack: +4/-0
  • Gender: Male
  • 77 Crusin Wagon

  • Total Badges: 6
    Badges: (View All)
    Mobile User Topic Starter Poll Voter Windows User Tenth year Anniversary Fifth year Anniversary
Re: Hood latch restore?
« Reply #2 on: May 12, 2017, 05:15:01 PM »
I have seen the electrolysis videos. I might try some evapo rust i have a jug i bought but haven't used it yet. Do you think bolt n nut instead of pop rivet would be stronger?

Sent from my SAMSUNG-SM-G930A using Tapatalk


Offline Wittsend

  • Pinto Master
  • *****
  • Posts: 2496
  • FeedBack: +241/-0

  • Total Badges: 8
    Badges: (View All)
    Tenth year Anniversary Mobile User Topic Starter Poll Voter 1000 Posts Linux User Windows User Fifth year Anniversary
Re: Hood latch restore?
« Reply #3 on: May 12, 2017, 10:20:51 PM »
I'd think you would need an internal spacer (maybe a stack of washers) if you used a bolt and nut so you didn't crush the halves when they were tightened.

Offline warhead2

  • Pinto Full Member
  • ***
  • Posts: 237
  • FeedBack: +4/-0
  • Gender: Male
  • 77 Crusin Wagon

  • Total Badges: 6
    Badges: (View All)
    Mobile User Topic Starter Poll Voter Windows User Tenth year Anniversary Fifth year Anniversary
Re: Hood latch restore?
« Reply #4 on: May 12, 2017, 10:55:52 PM »
Yeah i see your point

Sent from my SAMSUNG-SM-G930A using Tapatalk


Offline russosborne

  • Pinto Master
  • *****
  • Posts: 2405
  • FeedBack: +47/-1
  • Gender: Male
  • Another Pinto Driver

  • Total Badges: 5
    Badges: (View All)
    Poll Voter Mobile User Topic Starter Signature 1000 Posts
Re: Hood latch restore?
« Reply #5 on: May 13, 2017, 08:54:47 PM »
If you really want to take one apart, I'd suggest getting a spare one to practice on just in case you find out you can't get it back together.
I'd go with the idea of soaking it in something as mentioned above. Granted you wouldn't really be able to paint/protect the inner workings afterwards, but probably the safest way to go. They didn't come painted on the inside anyway, so as long as you keep it lubed it should be good to go.
Russ
In Glendale, Arizona

RIP Casey, Mallory, Abby, and Sadie. We miss you.

79 Pinto ESS fully caged fun car. In progress. 8inch 4.10 gears. 351C and a T5 waiting to go in.

Offline warhead2

  • Pinto Full Member
  • ***
  • Posts: 237
  • FeedBack: +4/-0
  • Gender: Male
  • 77 Crusin Wagon

  • Total Badges: 6
    Badges: (View All)
    Mobile User Topic Starter Poll Voter Windows User Tenth year Anniversary Fifth year Anniversary
Re: Hood latch restore?
« Reply #6 on: May 14, 2017, 02:56:46 AM »
Yeah im thinking thats best plan. just paint the outside

Sent from my SAMSUNG-SM-G930A using Tapatalk


Offline Reeves1

  • Pinto Master
  • *****
  • Posts: 2158
  • FeedBack: +104/-0
  • Gender: Male
  • BAWS302

  • Total Badges: 6
    Badges: (View All)
    Tenth year Anniversary Topic Starter Signature Fifth year Anniversary Windows User 1000 Posts
Re: Hood latch restore?
« Reply #7 on: May 14, 2017, 05:43:06 AM »
Local rad shop acid dipped a part for me, then I cleaned & POR 15 coated.

But with your part, it would need an anodized (?) type dip.
I'd have to google how to....

(zinc plating ?)