Current Classifieds

72 Pinto parts
Date: 12/04/2018 09:56 pm
parting out 1975 & 80 pintos
Date: 04/28/2018 04:12 pm
72 pinto drag car

Date: 07/08/2017 08:25 pm
1970-1973 Gas Tank/Blue Dash
Date: 02/07/2019 11:57 pm
'79 4 speed manual shifter needed
Date: 07/30/2018 04:32 pm
1971 Pinto

Date: 03/04/2017 11:28 pm
turbo 4 cyl and aod trans
Date: 12/14/2019 04:55 pm
1978 hatch back

Date: 11/29/2019 03:18 pm
1978 need kick panels and rear hatch struts and upper and lower mounts
Date: 11/29/2018 10:26 am
13" Style Steel Trim Rings

Date: 10/09/2020 10:35 pm
1980 hood needed
Date: 04/23/2020 10:41 pm
v8 springs
Date: 05/07/2017 04:46 pm

« previous next »
Pages: [1]   Go Down

Author Topic: Engine conversion complete  (Read 1358 times)

0 Members and 1 Guest are viewing this topic.

Offline pintoguy76

  • Pinto Master
  • *****
  • Posts: 936
  • FeedBack: +11/-0
  • Gender: Male
  • Pinto Driver

    • Total Badges: 7
    Badges: (View All)
    Topic Starter Signature Mobile User Poll Voter Tenth year Anniversary Windows User Fifth year Anniversary
Engine conversion complete
« on: August 13, 2013, 12:25:19 PM »
I finally got the exhaust on my 74 wagon connected to the new engine today. It runs great and is nice n quiet.  Still have the check engine light on (yes I even wired that up!) but it is due to a couple minor things. EGR valve which has no vacuum lines run to it right now, and no VSS either. Also i believe the ignition control module is popping some codes, but its running great so I will leave it alone for now.


I will have to have a custom cable made for the speedometer probably. I think a VSS from a T5 will work in the pinto transmission, but the cable is different. And I believe a mustang cable will probably be too short.


The EGR will be no big deal. A couple vacuum lines and its done.


The ICM... well. Thats a $150 part and a couple screws holding it on. No biggie either, except for the cost. Like I said as long as its running fine, i'm not gonna worry about that.
Logged
1974 Ford Pinto Wagon with 1991 Mustang DIS EFI 2.3 and stock Pinto 4 Speed
 
1996 Chevy C2500 Suburban with 6.5L Turbo Diesel/4L80E 4x2

1980 Volvo 265 with 1997 S-10 4.3 and a modified 700R4

2010 GMC Sierra SLE 1500 4x2 5.3 6L80E

Offline pintoguy76

  • Pinto Master
  • *****
  • Posts: 936
  • FeedBack: +11/-0
  • Gender: Male
  • Pinto Driver

    • Total Badges: 7
    Badges: (View All)
    Topic Starter Signature Mobile User Poll Voter Tenth year Anniversary Windows User Fifth year Anniversary
Re: Engine conversion complete
« Reply #1 on: October 14, 2013, 08:41:26 PM »
Finally had to replace the ICM. $20 at the salvage yard  ;D ;D  But it runs great again. Hooked up the EGR tho I didnt know which was the inlet and which was the outlet on the solenoid so it might be hooked up backwards.


Check engine light is still on. Guess its because of the lack of a VSS but IDK for sure. The ECM is also mad about the power steering pressure switch missing and not having the brake on/of wire hooked up. Dont know if all of those codes will trigger the CEL or not...
Logged
1974 Ford Pinto Wagon with 1991 Mustang DIS EFI 2.3 and stock Pinto 4 Speed
 
1996 Chevy C2500 Suburban with 6.5L Turbo Diesel/4L80E 4x2

1980 Volvo 265 with 1997 S-10 4.3 and a modified 700R4

2010 GMC Sierra SLE 1500 4x2 5.3 6L80E

Offline amc49

  • PCCA VIP
  • Pinto Master
  • ***
  • Posts: 1256
  • FeedBack: +242/-1
  • Another Pinto Driver

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Poll Voter Windows User 1000 Posts
Re: Engine conversion complete
« Reply #2 on: October 14, 2013, 09:38:16 PM »
Yes, they will. What basic year of EEC system you running on that thing?

Never mind, found it in another post.......... ........
Logged
Pages: [1]   Go Up
« previous next »