Current Classifieds

Looking for front seats
Date: 08/10/2021 09:54 pm
Need a 1976 runabout instrument cluster replacement
Date: 12/26/2016 04:29 pm
Pinto porthole exterior trim wanted
Date: 03/30/2021 12:29 pm
Early 2.0 engines
Date: 05/09/2018 12:45 pm
Bumper, grill and fender wanted
Date: 12/24/2016 04:13 pm
2.3 bellhousing stick
Date: 07/24/2019 06:50 pm
1973 Pinto Pangra

Date: 07/08/2019 10:09 pm
72 Pinto racecar, 2.3 ARCA engine, Quaife trans
Date: 01/10/2022 03:41 pm
72 Pinto parts
Date: 12/04/2018 09:56 pm
Mirror
Date: 04/15/2020 01:42 pm
Front sway bar frame brackets
Date: 07/13/2017 01:05 am
1972 pinto grill
Date: 02/27/2018 12:13 am

Author Topic: drop spindles on a 73 runabout  (Read 3671 times)

0 Members and 1 Guest are viewing this topic.

Offline vonkysmeed

  • Pinto Sr. Member
  • ****
  • Posts: 342
  • FeedBack: +4/-0
  • Gender: Male
  • 73 runabout - PCCA Ride #099
    • Project Frankenpinto

  • Total Badges: 7
    Badges: (View All)
    Topic Starter Signature Poll Voter Photographer Webmaster Tenth year Anniversary Fifth year Anniversary
drop spindles on a 73 runabout
« on: June 23, 2012, 11:17:18 PM »
will a drop spindle from a 74+ fit on a 73
73 Pinto Runabout
351w from 74 galaxie
Heads from 69 Mercury Cougar
82 Mustang GT SROD Transmission and driveshaft
Mustang II rear end with Fairmont 3rd member
6 point cage

Offline PintoMan1

  • Pinto Sr. Member
  • ****
  • Posts: 400
  • FeedBack: +0/-0
  • Gender: Male

  • Total Badges: 6
    Badges: (View All)
    Tenth year Anniversary Topic Starter Signature Poll Voter Windows User Fifth year Anniversary
Re: drop spindles on a 73 runabout
« Reply #1 on: June 24, 2012, 03:21:20 PM »
they will. i did it. the only thing i had to do was have the hole for the tie rod end reemed out to fit the taper of the tie rod. looks great on the car.
1973 pinto runabout

Offline vonkysmeed

  • Pinto Sr. Member
  • ****
  • Posts: 342
  • FeedBack: +4/-0
  • Gender: Male
  • 73 runabout - PCCA Ride #099
    • Project Frankenpinto

  • Total Badges: 7
    Badges: (View All)
    Topic Starter Signature Poll Voter Photographer Webmaster Tenth year Anniversary Fifth year Anniversary
Re: drop spindles on a 73 runabout
« Reply #2 on: June 24, 2012, 06:36:02 PM »
cool, will give it a try later this summer
73 Pinto Runabout
351w from 74 galaxie
Heads from 69 Mercury Cougar
82 Mustang GT SROD Transmission and driveshaft
Mustang II rear end with Fairmont 3rd member
6 point cage

Offline vonkysmeed

  • Pinto Sr. Member
  • ****
  • Posts: 342
  • FeedBack: +4/-0
  • Gender: Male
  • 73 runabout - PCCA Ride #099
    • Project Frankenpinto

  • Total Badges: 7
    Badges: (View All)
    Topic Starter Signature Poll Voter Photographer Webmaster Tenth year Anniversary Fifth year Anniversary
Re: drop spindles on a 73 runabout
« Reply #3 on: June 25, 2012, 10:08:50 PM »
they will. i did it. the only thing i had to do was have the hole for the tie rod end reemed out to fit the taper of the tie rod. looks great on the car.

can you just use 74 tie rod end?
73 Pinto Runabout
351w from 74 galaxie
Heads from 69 Mercury Cougar
82 Mustang GT SROD Transmission and driveshaft
Mustang II rear end with Fairmont 3rd member
6 point cage

Offline oldkayaker

  • Pinto Master
  • *****
  • Posts: 758
  • FeedBack: +114/-0
  • Gender: Male

  • Total Badges: 5
    Badges: (View All)
    Topic Starter Signature Windows User Tenth year Anniversary Fifth year Anniversary
Re: drop spindles on a 73 runabout
« Reply #4 on: June 26, 2012, 04:38:58 AM »
I have not done this swap.  Based on my measurements, the 73 and 74  tie rod ends are the same.  Rockauto.com also shows the same part number for both.  The 71-72 are the ones with smaller tie rod ends.  This assumes no end of year carry overs.
 
Note that 74  spindles (including the drop spindles) are about 7/8" taller measured ball joint to ball joint.  If this is the only change, I believe this would increase camber gain during bump.  I measured the vertical distance from the lower ball joint hole to the spindle centerline with the following results: 72~2.5", 79~1.4", drop~3.4".  So the 2" drop spindles will lower the 71-73 cars by about 7/8" based on this.  Again this is based on component measurements and not on a final installation.
Jerry J - Jupiter, Florida

Offline 71hotrodpinto

  • Pinto Sr. Member
  • ****
  • Posts: 389
  • FeedBack: +33/-0
  • Gender: Male
  • Will I EVER finish this car?

  • Total Badges: 8
    Badges: (View All)
    Topic Starter Signature Tenth year Anniversary Windows User Photographer Apple User Mobile User Fifth year Anniversary
Re: drop spindles on a 73 runabout
« Reply #5 on: June 26, 2012, 02:09:25 PM »
The 73 from my findings are a draw of the deck. They changed over to the 74-up suspension mid year. So you never know what you have untill you check everything. The 71-72 has the rack that mounts on flat perches. The 74 and up has the 2 big bolts and bushings that are horizontal into the ground and go into the crossmember.
 If im not mistaken ive actually "heard" that they mixed up some as well. 72 rack with 74 suspension.
 
Good luck! :)
 
 


95' 302,Forged Pistons,Polished rods
B303,1.7 Rockers,beehives
'68 port/polish heads                   
Coated Must II headers
Edelbrock Airgap
Holley570,Msd dist,CraneHI6
Mil