Current Classifieds

2.3 engine and other parts- Free
Date: 12/13/2016 10:25 am
Parts for 74 Squire Wagon
Date: 09/16/2019 07:35 pm
76 Pinto Wagon
Date: 07/08/2020 05:44 pm
Wanted 1973 Ford right fender
Date: 06/03/2017 08:50 pm
79-80 full glass hatch

Date: 01/04/2017 04:04 am
2 Pinto Wagons for Sale

Date: 10/29/2018 02:02 pm
1971 Pinto Parting out

Date: 07/06/2018 01:11 pm
Pinto wagon Parts
Date: 06/23/2021 03:25 pm
79 pinto driveshaft
Date: 08/18/2018 02:03 pm
1971 Pinto Do It Yourself Manual

Date: 03/06/2017 01:19 am
Various parts for 1980 Pony (good to N.O.S. condition
Date: 06/07/2018 01:45 am
Need right door for pinto or bobcat 1977 to 1980 station wagon
Date: 08/03/2018 09:19 am

Author Topic: Clutch cable through firewall  (Read 1110 times)

0 Members and 1 Guest are viewing this topic.

Offline xonknor

  • Pinto Driver
  • *
  • Posts: 6
  • FeedBack: +2/-0
  • Another Pinto Driver

  • Total Badges: 2
    Badges: (View All)
    Topic Starter Mobile User
Clutch cable through firewall
« on: May 07, 2018, 12:58:11 PM »
 It says I am not able to post a picture, but can anyone advise me on the clip that holds the clutch cable into the hole on the firewall on a 1979 Pinto? Mine seems to have pulled out and maybe that is why it will not start? Neutral safety starter switch  not engaging because clutch cable will not fully Pull?

Offline Wittsend

  • Pinto Master
  • *****
  • Posts: 2496
  • FeedBack: +241/-0

  • Total Badges: 8
    Badges: (View All)
    Tenth year Anniversary Mobile User Topic Starter Poll Voter 1000 Posts Linux User Windows User Fifth year Anniversary
Re: Clutch cable through firewall
« Reply #1 on: May 07, 2018, 04:25:26 PM »
It has been a LONG time but I recall there were finger like, spring loaded prongs that extended into the firewall. Hence it should pop into place and be held with the prongs.  Typically people have difficulty REMOVING the cable. I recall using a split piece of tubing and then a hose clamp to compress the prong to remove the cable. it was a fine line between compressing the prongs enough to fit through the hole and having enough loseness to actually move the cable.

If the prongs are missing you might as a temporary fix (do at your own risk) try a hose clamp to hold the cable in place.

Offline TIGGER

  • PCCA Charter Member
  • Pinto Master
  • *
  • Posts: 2422
  • FeedBack: +70/-0
  • Gender: Male

  • Total Badges: 10
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User Apple User Mobile User 1000 Posts Tenth year Anniversary Fifth year Anniversary Photographer
Re: Clutch cable through firewall
« Reply #2 on: May 07, 2018, 06:53:57 PM »
It is very similar to how an ebrake cable is attached to the brake backing plate.
79 4cyl Wagon
73 Turbo HB
78 Cruising Wagon (sold 8/6/11)

Offline dick1172762

  • Vintage Pinto Racer
  • PCCA Management Board
  • Pinto Sr. Master
  • ******
  • Posts: 2623
  • FeedBack: +362/-0
  • Gender: Male
  • I'm a llama!

  • Total Badges: 7
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User 1000 Posts Tenth year Anniversary Fifth year Anniversary
Re: Clutch cable through firewall
« Reply #3 on: May 08, 2018, 10:41:54 AM »
I have used a small hose clamp to clamp down the barbs, then I pushed the barbs through the fire wall and then I removed the hose clamp. Easy fix.
Its better to be a has-been, than a never was.

Offline xonknor

  • Pinto Driver
  • *
  • Posts: 6
  • FeedBack: +2/-0
  • Another Pinto Driver

  • Total Badges: 2
    Badges: (View All)
    Topic Starter Mobile User
Re: Clutch cable through firewall
« Reply #4 on: May 15, 2018, 11:01:01 AM »
Thanks. It does have the flat prongs, and although that is a tight spot for 2 hands, I got it back in and will fasten it as suggested. Thanks everyone!

Offline dave1987

  • Pinto Sr. Master
  • ******
  • Posts: 3431
  • FeedBack: +25/-0
  • Gender: Male

  • Total Badges: 11
    Badges: (View All)
    Topic Starter Signature Tenth year Anniversary Poll Voter Mobile User Apple User Linux User Windows User 1000 Posts Fifth year Anniversary Photographer
Re: Clutch cable through firewall
« Reply #5 on: May 17, 2018, 12:48:00 AM »
I had this issue a year or so after I started driving my 78 Sedan.


I ended up replacing the Pinto cable with a Mustang II cable, using the adjuster tube from the Mustang II on the firewall. No issues in the 6 years daily driving it this way, same cable through three clutch rebuilds and three different transmissions.
1978 Ford Pinto Sedan - Family owned since new

Remembering Jeff Fitcher with every drive in my 78 Sedan.

I am a Pinto Surgeon. Fixing problems and giving Pintos a chance to live again is more than a hobby, it's a passion!