Current Classifieds

New cam

Date: 01/23/2017 05:11 pm
WTB: 2.0 Mech tach drive distributor
Date: 04/14/2023 06:15 am
2.3/C-4 torque converter needed
Date: 02/08/2018 02:26 pm
Offenhauser 6114 dp
Date: 09/12/2017 10:26 pm
Crane Cam
Date: 02/26/2018 07:50 am
Weather Strip, Muffler, Splash Shields

Date: 02/21/2022 11:11 pm
'72 Runabout Drivers Side Door Hinge Set
Date: 12/15/2018 02:21 am
73 Runabout

Date: 11/20/2017 03:19 pm
1974 Pinto Misc. moldings & parts

Date: 12/20/2016 10:47 pm
Beautiful 1980 Pinto

Date: 04/13/2020 11:53 am
78 hatchback

Date: 03/12/2023 06:50 pm
72 pinto drag car

Date: 07/08/2017 08:25 pm

Author Topic: ball joints  (Read 1075 times)

0 Members and 1 Guest are viewing this topic.

Offline HOSS429

  • Pinto Full Member
  • ***
  • Posts: 222
  • FeedBack: +22/-0
  • old ford guy

  • Total Badges: 5
    Badges: (View All)
    Tenth year Anniversary Fifth year Anniversary Topic Starter Poll Voter Windows User
ball joints
« on: June 01, 2016, 04:50:50 PM »
i have`nt been here in a day or two and it took me forever to find how to open a thread .. i looked and found plenty of threads about ball joints but could not open any .. anyway can someone tell me the difference between 73 ball joints and later ones ,,  the only thing i can see is the bolt holes are a few thousands off . i have both on hand .. believe me i can open up a bolt hole on a 27 $ 1975 ball joint easy enuff to keep from paying 127 $ for a 1973 ball joint ...

Offline Wittsend

  • Pinto Master
  • *****
  • Posts: 2499
  • FeedBack: +241/-0

  • Total Badges: 8
    Badges: (View All)
    Tenth year Anniversary Mobile User Topic Starter Poll Voter 1000 Posts Linux User Windows User Fifth year Anniversary
Re: ball joints
« Reply #1 on: June 01, 2016, 06:34:48 PM »
Beyond the math word problem (answer, $102) I'd say to check the taper and depth there of. The proper fitment to the spindle would be critical.  Also, do the mounting holes (or modifying the holes) offset the ball joint as it mounts on the arm? That could throw the camber out to a point it can't adjust back to spec. but otherwise I agree that if the part is adaptable use it.  all the 71-73 suspension stuff is expensive due to its age and smaller sample application.  In my mind people should be snagging every decent rotor they can find because I believe they are over $100 too..

Offline HOSS429

  • Pinto Full Member
  • ***
  • Posts: 222
  • FeedBack: +22/-0
  • old ford guy

  • Total Badges: 5
    Badges: (View All)
    Tenth year Anniversary Fifth year Anniversary Topic Starter Poll Voter Windows User
Re: ball joints
« Reply #2 on: June 01, 2016, 07:25:02 PM »
 ahh 1  new math .. it confuses me .. 127 - 27 is now 102 .. no wonder i cant make the joints fit ( but i did ) ...

Offline Wittsend

  • Pinto Master
  • *****
  • Posts: 2499
  • FeedBack: +241/-0

  • Total Badges: 8
    Badges: (View All)
    Tenth year Anniversary Mobile User Topic Starter Poll Voter 1000 Posts Linux User Windows User Fifth year Anniversary
Re: ball joints
« Reply #3 on: June 01, 2016, 11:54:13 PM »
My bad. Thought the 27 was 25 must have caught that from the "5" in the 1975. Why was it that I always saw the error AFTER the paper was corrected??? So how did they fit? Or better said what did you do to make them fit?