Current Classifieds

1973 Pangra gauge and tach panel

Date: 11/02/2019 10:25 am
Need Brakes for 1971 Pinto
Date: 04/27/2018 11:48 pm
Great Cruise wagon

Date: 12/17/2016 03:39 pm
Built and Injected early 2000cc Engine

Date: 04/10/2017 07:30 pm
79 Wagon with many extras
Date: 07/08/2020 04:18 pm
Need Brakes for 1971 Pinto
Date: 04/27/2018 11:48 pm
78 fender and hood
Date: 03/23/2021 01:07 pm
1971 Pinto 5.0L

Date: 12/02/2017 12:23 am
parting out 1975 & 80 pintos
Date: 04/28/2018 04:12 pm
76 pinto sedan sbc/bbc project for sale $1700 obo

Date: 03/27/2017 10:07 pm
1974 Pinto Misc. moldings & parts

Date: 12/20/2016 10:47 pm
WANTED Hood Prop Rod
Date: 01/17/2017 02:47 pm

Author Topic: ball joints  (Read 1056 times)

0 Members and 1 Guest are viewing this topic.

Offline HOSS429

  • Pinto Full Member
  • ***
  • Posts: 222
  • FeedBack: +22/-0
  • old ford guy

  • Total Badges: 5
    Badges: (View All)
    Tenth year Anniversary Fifth year Anniversary Topic Starter Poll Voter Windows User
ball joints
« on: June 01, 2016, 04:50:50 PM »
i have`nt been here in a day or two and it took me forever to find how to open a thread .. i looked and found plenty of threads about ball joints but could not open any .. anyway can someone tell me the difference between 73 ball joints and later ones ,,  the only thing i can see is the bolt holes are a few thousands off . i have both on hand .. believe me i can open up a bolt hole on a 27 $ 1975 ball joint easy enuff to keep from paying 127 $ for a 1973 ball joint ...

Offline Wittsend

  • Pinto Master
  • *****
  • Posts: 2496
  • FeedBack: +241/-0

  • Total Badges: 8
    Badges: (View All)
    Tenth year Anniversary Mobile User Topic Starter Poll Voter 1000 Posts Linux User Windows User Fifth year Anniversary
Re: ball joints
« Reply #1 on: June 01, 2016, 06:34:48 PM »
Beyond the math word problem (answer, $102) I'd say to check the taper and depth there of. The proper fitment to the spindle would be critical.  Also, do the mounting holes (or modifying the holes) offset the ball joint as it mounts on the arm? That could throw the camber out to a point it can't adjust back to spec. but otherwise I agree that if the part is adaptable use it.  all the 71-73 suspension stuff is expensive due to its age and smaller sample application.  In my mind people should be snagging every decent rotor they can find because I believe they are over $100 too..

Offline HOSS429

  • Pinto Full Member
  • ***
  • Posts: 222
  • FeedBack: +22/-0
  • old ford guy

  • Total Badges: 5
    Badges: (View All)
    Tenth year Anniversary Fifth year Anniversary Topic Starter Poll Voter Windows User
Re: ball joints
« Reply #2 on: June 01, 2016, 07:25:02 PM »
 ahh 1  new math .. it confuses me .. 127 - 27 is now 102 .. no wonder i cant make the joints fit ( but i did ) ...

Offline Wittsend

  • Pinto Master
  • *****
  • Posts: 2496
  • FeedBack: +241/-0

  • Total Badges: 8
    Badges: (View All)
    Tenth year Anniversary Mobile User Topic Starter Poll Voter 1000 Posts Linux User Windows User Fifth year Anniversary
Re: ball joints
« Reply #3 on: June 01, 2016, 11:54:13 PM »
My bad. Thought the 27 was 25 must have caught that from the "5" in the 1975. Why was it that I always saw the error AFTER the paper was corrected??? So how did they fit? Or better said what did you do to make them fit?