Current Classifieds

2.3 carb intake

Date: 07/15/2020 09:25 pm
72 Pinto racecar, 2.3 ARCA engine, Quaife trans
Date: 01/10/2022 03:41 pm
1976 Squire wagon

Date: 09/12/2018 10:30 pm
A.c. alternator hrackets
Date: 09/03/2017 12:11 pm
Holley 2305 progressive 2 bbl carb 350cfm

Date: 10/11/2019 11:13 am
1978 bobcat 4speed shifter
Date: 11/02/2023 09:51 pm
Wanted 1971-73 pinto 2.0 4 speed manual transmission
Date: 03/06/2019 06:40 pm
Tire needed p185/80r13
Date: 12/31/2017 09:08 pm
1976 Squire wagon

Date: 09/12/2018 10:30 pm
Leaf Spring Mount Rubber Insulator
Date: 08/05/2018 01:58 pm
'79 Ford Pinto, Green,

Date: 10/29/2019 11:50 am
2.8 Engine mount brackets
Date: 12/28/2016 11:42 am

Author Topic: Yukon cut to fit rear axles-thoughts?  (Read 462 times)

0 Members and 1 Guest are viewing this topic.

Offline russosborne

  • Pinto Master
  • *****
  • Posts: 2405
  • FeedBack: +47/-1
  • Gender: Male
  • Another Pinto Driver

  • Total Badges: 5
    Badges: (View All)
    Poll Voter Mobile User Topic Starter Signature 1000 Posts
Yukon cut to fit rear axles-thoughts?
« on: October 14, 2018, 12:15:25 AM »
Found these on Summit's site.
https://www.summitracing.com/parts/yga-21410
They are listed for the 79 8inch Pinto rear.
Thinking it might be better/easier to go with new axles instead of getting the old ones welded/redrilled.
Just not familiar with the cut to fit option.
Seems Yukon is a decent source overall.
Thanks,
Russ
In Glendale, Arizona

RIP Casey, Mallory, Abby, and Sadie. We miss you.

79 Pinto ESS fully caged fun car. In progress. 8inch 4.10 gears. 351C and a T5 waiting to go in.

Offline pinto_one

  • Pinto Master
  • *****
  • Posts: 1008
  • FeedBack: +70/-0
  • Gender: Male
  • Pinto-One

  • Total Badges: 10
    Badges: (View All)
    1000 Posts Photographer Tenth year Anniversary Topic Starter Signature Poll Voter Mobile User Apple User Windows User Fifth year Anniversary
Re: Yukon cut to fit rear axles-thoughts?
« Reply #1 on: October 14, 2018, 06:38:43 PM »
Done that back in the late 70s Russ , they did not have much of a larger wheel for the pinto , used maverick axles , remember that I had to cut one side a 1/4 inch , later used granda axles and front rotors , the last one I helped a friend and he found that 84 to 86 ranger axles would fit with no mods , drums were used also , yep the ranger used the same shoes as the pinto along with the same wheel bearings , it was all bolt together , guess you can pull one axle at a time and bring it to a yard to match up if you know someone there , then there is the Bronco II also , just donít like the idea of a 10 inch long spline and at 200 bucks a pop that 400 and you donít have bearings yet , the yard here charges 10 to 15 an axle , much cheaper
76 Pinto sedan V6 , 79 pinto cruiser wagon V6 soon to be diesel or 4.0

Offline russosborne

  • Pinto Master
  • *****
  • Posts: 2405
  • FeedBack: +47/-1
  • Gender: Male
  • Another Pinto Driver

  • Total Badges: 5
    Badges: (View All)
    Poll Voter Mobile User Topic Starter Signature 1000 Posts
Re: Yukon cut to fit rear axles-thoughts?
« Reply #2 on: October 14, 2018, 10:52:48 PM »
Thanks.
It's something I am thinking about.
Russ
In Glendale, Arizona

RIP Casey, Mallory, Abby, and Sadie. We miss you.

79 Pinto ESS fully caged fun car. In progress. 8inch 4.10 gears. 351C and a T5 waiting to go in.