Current Classifieds

Clutch Fork
Date: 03/31/2018 09:12 pm
1974 Pinto Misc. moldings & parts

Date: 12/20/2016 10:47 pm
Need Brakes for 1971 Pinto
Date: 04/27/2018 11:48 pm
1974 Pinto Passenger side door glass and door parts

Date: 02/18/2017 05:55 pm
1974 Pinto Right Rear Interior Trim Panel

Date: 02/18/2017 04:44 pm
Accelerator Pump Diaphram for 1978 Pinto
Date: 09/03/2018 08:58 am
Wanted 2.3 engine mount brackets and mounts
Date: 02/14/2018 01:34 am
GRILLE NEEDED '71,'72,'73 for a '73 Pinto
Date: 02/10/2017 09:30 am
1977 Left Side quarter panel
Date: 06/10/2019 04:16 pm
71-73 Pinto Parts

Date: 06/06/2019 10:47 am
Ford 2.3L new gaskets for sale
Date: 12/10/2016 04:11 pm
79-80 full glass hatch

Date: 01/04/2017 04:04 am

Author Topic: which cap for this valve cover?  (Read 5685 times)

0 Members and 1 Guest are viewing this topic.

Offline dick1172762

  • Vintage Pinto Racer
  • PCCA Management Board
  • Pinto Sr. Master
  • ******
  • Posts: 2623
  • FeedBack: +362/-0
  • Gender: Male
  • I'm a llama!

  • Total Badges: 7
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User 1000 Posts Tenth year Anniversary Fifth year Anniversary
Re: which cap for this valve cover?
« Reply #30 on: May 02, 2014, 07:54:04 AM »
Metric bolts too.
Its better to be a has-been, than a never was.

Offline poomwah

  • Pinto Full Member
  • ***
  • Posts: 205
  • FeedBack: +3/-0

  • Total Badges: 3
    Badges: (View All)
    Topic Starter Windows User Fifth year Anniversary
Re: which cap for this valve cover?
« Reply #31 on: May 02, 2014, 01:28:50 PM »
6mm by the look of it

Offline poomwah

  • Pinto Full Member
  • ***
  • Posts: 205
  • FeedBack: +3/-0

  • Total Badges: 3
    Badges: (View All)
    Topic Starter Windows User Fifth year Anniversary
Re: which cap for this valve cover?
« Reply #32 on: May 02, 2014, 06:56:38 PM »
got the breather elbow today, but the cap that they had at autozone won't thread in.

Offline D.R.Ball

  • Pinto Sr. Member
  • ****
  • Posts: 558
  • FeedBack: +36/-2
  • Gender: Male

  • Total Badges: 5
    Badges: (View All)
    Topic Starter Tenth year Anniversary Poll Voter Windows User Fifth year Anniversary
Re: which cap for this valve cover?
« Reply #33 on: May 03, 2014, 10:27:23 AM »
The breather is a push on not a thread on, the oil filler cap is a screw on...

Offline poomwah

  • Pinto Full Member
  • ***
  • Posts: 205
  • FeedBack: +3/-0

  • Total Badges: 3
    Badges: (View All)
    Topic Starter Windows User Fifth year Anniversary
Re: which cap for this valve cover?
« Reply #34 on: May 03, 2014, 11:19:24 PM »
right, the breather fit perfectly. The cap they had listed had the wrong thread.
 I took the valve cover into a different store and matched it up.