Current Classifieds

Drivers side door panel Orange
Date: 05/22/2018 01:54 pm
pinto floor mats??

Date: 01/11/2017 07:27 am
WTB 1974 or 1975 Pinto Grille and Turn Signals
Date: 04/08/2018 05:47 pm
1972 pinto grill
Date: 02/27/2018 12:13 am
Need a 1976 runabout instrument cluster replacement
Date: 12/26/2016 04:29 pm
1973 Interior parts wanted
Date: 01/02/2017 11:02 pm
1980 Pinto Parts

Date: 08/05/2020 04:20 pm
1971 Pinto (survivor)

Date: 05/15/2022 04:42 pm
72' hatchback parts wanted
Date: 08/25/2019 02:57 am
WTB Cruising Wagon
Date: 12/07/2016 05:35 pm
4-14" Chrome Plated Wheels 4 x 108 + 0mm offset with new tires

Date: 09/12/2018 12:33 pm
parts needed
Date: 02/20/2017 07:58 am

« previous next »
Pages: [1]   Go Down

Author Topic: wheel backspacing question  (Read 1263 times)

0 Members and 1 Guest are viewing this topic.

Offline shuffln

  • Pinto Member
  • **
  • Posts: 55
  • FeedBack: +7/-1
  • Another Pinto Driver

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Linux User Mobile User Windows User
wheel backspacing question
« on: September 14, 2015, 06:10:40 AM »
found a nice of center line rims for my 79 bobcat but i'm concerned about the backspacing for the rear. they are 15 x 7 and i was told they have a 5" backspacing. i'm not sure if 5" backspacing will work without a spacer. 
Logged

Offline dick1172762

  • Vintage Pinto Racer
  • PCCA Management Board
  • Pinto Sr. Master
  • ******
  • Posts: 2623
  • FeedBack: +362/-0
  • Gender: Male
  • I'm a llama!

    • Total Badges: 7
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User 1000 Posts Tenth year Anniversary Fifth year Anniversary
Re: wheel backspacing question
« Reply #1 on: September 14, 2015, 07:26:01 AM »
4" backspace will just touch on the upper control arm. With a 15x7 wheel 3" backspace will allow the wheel/tire to fill up the wheel well just right.  5" backspace will not work without a spacer of 1" or more.
Logged
Its better to be a has-been, than a never was.

Offline shuffln

  • Pinto Member
  • **
  • Posts: 55
  • FeedBack: +7/-1
  • Another Pinto Driver

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Linux User Mobile User Windows User
Re: wheel backspacing question
« Reply #2 on: September 14, 2015, 11:23:56 AM »
Will they fit on the rear?
Logged

Offline one2.34me

  • Pinto Full Member
  • ***
  • Posts: 179
  • FeedBack: +56/-0
  • Gender: Male

    • Total Badges: 7
    Badges: (View All)
    Tenth year Anniversary Signature Topic Starter Mobile User Poll Voter Windows User Fifth year Anniversary
Re: wheel backspacing question
« Reply #3 on: September 14, 2015, 01:09:39 PM »
I have a set of 15x7 Mustang 10 hole wheels on my 75 Pinto. They're 5" backspace and the rears clear fine. The fronts didn't. The upper ball joint bolt heads dug into the rims and locked the front tires. I shaved the upper ball joint bolt heads and a bit of the upper A frame and added 5/16" wheel spacers L and R. the wheels clear completely now, EXCEPT on a full lock right turn. Then there is a rub on the R/F wheel. The rubber is 195/55-15. Also like Dick says with the 5" backspace, the wheels are tucked into the wheel wells pretty far.
Logged
Pages: [1]   Go Up
« previous next »