Current Classifieds

72 pinto

Date: 06/23/2016 12:40 pm
Wanted Pinto Fiberglass Body Parts
Date: 08/16/2018 08:54 am
Rare parts for sale
Date: 09/10/2018 08:38 am
72 Pinto racecar, 2.3 ARCA engine, Quaife trans
Date: 01/10/2022 03:41 pm
72 Runabout Sprint Edition

Date: 04/25/2018 02:51 pm
WTB Manual Transmission Clutch Pedal for '78
Date: 03/29/2019 07:20 am
Looking for a 1980 windshield
Date: 07/30/2020 04:51 pm
1973 Pinto Runabout

Date: 08/17/2022 06:27 pm
Wiring diagram Ignition switch 72 2.0 4 speed pinto wagon
Date: 12/31/2017 11:14 pm
pinto floor mats??

Date: 01/11/2017 07:27 am
hubcaps

Date: 06/05/2018 09:13 pm
78 Cruising Wagon at Mecum Chattanooga

Date: 09/02/2021 08:21 am

Author Topic: wheel backspacing question  (Read 1245 times)

0 Members and 1 Guest are viewing this topic.

Offline shuffln

  • Pinto Member
  • **
  • Posts: 55
  • FeedBack: +7/-1
  • Another Pinto Driver

  • Total Badges: 4
    Badges: (View All)
    Topic Starter Linux User Mobile User Windows User
wheel backspacing question
« on: September 14, 2015, 06:10:40 AM »
found a nice of center line rims for my 79 bobcat but i'm concerned about the backspacing for the rear. they are 15 x 7 and i was told they have a 5" backspacing. i'm not sure if 5" backspacing will work without a spacer. 

Offline dick1172762

  • Vintage Pinto Racer
  • PCCA Management Board
  • Pinto Sr. Master
  • ******
  • Posts: 2623
  • FeedBack: +362/-0
  • Gender: Male
  • I'm a llama!

  • Total Badges: 7
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User 1000 Posts Tenth year Anniversary Fifth year Anniversary
Re: wheel backspacing question
« Reply #1 on: September 14, 2015, 07:26:01 AM »
4" backspace will just touch on the upper control arm. With a 15x7 wheel 3" backspace will allow the wheel/tire to fill up the wheel well just right.  5" backspace will not work without a spacer of 1" or more.
Its better to be a has-been, than a never was.

Offline shuffln

  • Pinto Member
  • **
  • Posts: 55
  • FeedBack: +7/-1
  • Another Pinto Driver

  • Total Badges: 4
    Badges: (View All)
    Topic Starter Linux User Mobile User Windows User
Re: wheel backspacing question
« Reply #2 on: September 14, 2015, 11:23:56 AM »
Will they fit on the rear?

Offline one2.34me

  • Pinto Full Member
  • ***
  • Posts: 179
  • FeedBack: +56/-0
  • Gender: Male

  • Total Badges: 7
    Badges: (View All)
    Tenth year Anniversary Signature Topic Starter Mobile User Poll Voter Windows User Fifth year Anniversary
Re: wheel backspacing question
« Reply #3 on: September 14, 2015, 01:09:39 PM »
I have a set of 15x7 Mustang 10 hole wheels on my 75 Pinto. They're 5" backspace and the rears clear fine. The fronts didn't. The upper ball joint bolt heads dug into the rims and locked the front tires. I shaved the upper ball joint bolt heads and a bit of the upper A frame and added 5/16" wheel spacers L and R. the wheels clear completely now, EXCEPT on a full lock right turn. Then there is a rub on the R/F wheel. The rubber is 195/55-15. Also like Dick says with the 5" backspace, the wheels are tucked into the wheel wells pretty far.