Current Classifieds

1971 yellow Pinto hatchback with limited edition chrome strips on rear door, 1600 cc engine

Date: 02/26/2017 03:22 pm
Drivers side door panel Orange
Date: 05/22/2018 02:27 pm
71-73 Hood
Date: 12/07/2018 06:22 pm
2.3 front sump oil pan
Date: 07/24/2018 03:17 pm
INTERIOR DELUX ARM RESTS - 2 PAIR

Date: 03/23/2018 09:23 pm
1971 2 lt Cam
Date: 10/10/2020 06:27 pm
Tubing bender 1/2 to 2 1/2 (3) inch roll cage / mufflers and more

Date: 03/13/2021 12:57 pm
convert to stick
Date: 05/19/2018 09:26 pm
1977 Front Sump 2.3 Oil Pan
Date: 09/14/2018 11:42 pm
Parts for 74 Squire Wagon
Date: 09/16/2019 07:35 pm
1980 Pinto-Shay for sale

Date: 07/07/2016 01:21 pm
71-73 sway bar
Date: 06/12/2021 10:12 am

« previous next »
Pages: [1]   Go Down

Author Topic: wheel backspacing question  (Read 1199 times)

0 Members and 1 Guest are viewing this topic.

Offline shuffln

  • Pinto Member
  • **
  • Posts: 55
  • FeedBack: +7/-1
  • Another Pinto Driver

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Linux User Mobile User Windows User
wheel backspacing question
« on: September 14, 2015, 06:10:40 AM »
found a nice of center line rims for my 79 bobcat but i'm concerned about the backspacing for the rear. they are 15 x 7 and i was told they have a 5" backspacing. i'm not sure if 5" backspacing will work without a spacer. 
Logged

Offline dick1172762

  • Vintage Pinto Racer
  • PCCA Management Board
  • Pinto Sr. Master
  • ******
  • Posts: 2623
  • FeedBack: +362/-0
  • Gender: Male
  • I'm a llama!

    • Total Badges: 7
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User 1000 Posts Tenth year Anniversary Fifth year Anniversary
Re: wheel backspacing question
« Reply #1 on: September 14, 2015, 07:26:01 AM »
4" backspace will just touch on the upper control arm. With a 15x7 wheel 3" backspace will allow the wheel/tire to fill up the wheel well just right.  5" backspace will not work without a spacer of 1" or more.
Logged
Its better to be a has-been, than a never was.

Offline shuffln

  • Pinto Member
  • **
  • Posts: 55
  • FeedBack: +7/-1
  • Another Pinto Driver

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Linux User Mobile User Windows User
Re: wheel backspacing question
« Reply #2 on: September 14, 2015, 11:23:56 AM »
Will they fit on the rear?
Logged

Offline one2.34me

  • Pinto Full Member
  • ***
  • Posts: 179
  • FeedBack: +56/-0
  • Gender: Male

    • Total Badges: 7
    Badges: (View All)
    Tenth year Anniversary Signature Topic Starter Mobile User Poll Voter Windows User Fifth year Anniversary
Re: wheel backspacing question
« Reply #3 on: September 14, 2015, 01:09:39 PM »
I have a set of 15x7 Mustang 10 hole wheels on my 75 Pinto. They're 5" backspace and the rears clear fine. The fronts didn't. The upper ball joint bolt heads dug into the rims and locked the front tires. I shaved the upper ball joint bolt heads and a bit of the upper A frame and added 5/16" wheel spacers L and R. the wheels clear completely now, EXCEPT on a full lock right turn. Then there is a rub on the R/F wheel. The rubber is 195/55-15. Also like Dick says with the 5" backspace, the wheels are tucked into the wheel wells pretty far.
Logged
Pages: [1]   Go Up
« previous next »