Current Classifieds

1978 need kick panels and rear hatch struts and upper and lower mounts
Date: 11/29/2018 10:26 am
nos core support

Date: 01/03/2020 09:39 pm
1980 Ford Pinto For Sale

Date: 07/01/2018 03:21 pm
2.0 performance parts, 2 intakes, header, ported head, more
Date: 10/25/2019 04:05 pm
Need Mustang II Manual Transmission Mount
Date: 04/21/2017 02:03 pm
Early V8 swap headers, damaged, fixable?
Date: 10/25/2019 03:30 pm
1971 Pinto 5.0L

Date: 12/02/2017 12:23 am
ENGINE COMPLETE 1971 PINTO
Date: 12/28/2017 03:55 pm
pinto floor mats??

Date: 01/11/2017 07:27 am
$300 Pinto for sale

Date: 04/19/2017 10:24 am
V8 rear end
Date: 04/12/2018 10:57 am
77-78 front grill
Date: 04/07/2017 12:35 am

« previous next »
Pages: [1]   Go Down

Author Topic: what socket for 2.3 head bolts  (Read 1523 times)

0 Members and 1 Guest are viewing this topic.

Offline waldo786

  • Pinto Full Member
  • ***
  • Posts: 236
  • FeedBack: +0/-0
  • Gender: Male

    • Total Badges: 5
    Badges: (View All)
    Tenth year Anniversary Topic Starter Poll Voter Windows User Fifth year Anniversary
what socket for 2.3 head bolts
« on: July 14, 2013, 12:52:07 PM »
Hello all, I am trying to remove my head bolts from my 2.3L ('76) and wasn't sure what size the bolts are.  They look like 1/2" 12 point socket, but I am not sure.  I also read on here that these can be reused?  Any clarifications would be helpful!  Thanks!
Logged

Offline Pinto5.0

  • Pinto Master
  • *****
  • Posts: 1974
  • FeedBack: +77/-0
  • Gender: Male
  • 80 hatch, 76 Wagon, 72 & 73 Sedans, 71 half hatch

    • Total Badges: 7
    Badges: (View All)
    Topic Starter Signature Poll Voter Mobile User Fifth year Anniversary Windows User 1000 Posts
Re: what socket for 2.3 head bolts
« Reply #1 on: July 14, 2013, 03:45:10 PM »
It is a 12 point but either 1/2" or 9/16". They are re-usable & I'm hearing preferred over ARP studs which are supposedly lacking enough threads on the block side.   
Logged
'73 Sedan (I'll get to it)
'76 Wagon driver
'80 hatch(Restoring to be my son's 1st car)~Callisto
'71 half hatch (bucket list Pinto)~Ghost
'72 sedan 5.0/T5~Lemon Squeeze

Offline 72pair

  • Pinto Sr. Member
  • ****
  • Posts: 269
  • FeedBack: +56/-0
  • Gender: Male

    • Total Badges: 6
    Badges: (View All)
    Tenth year Anniversary Topic Starter Signature Poll Voter Windows User Fifth year Anniversary
Re: what socket for 2.3 head bolts
« Reply #2 on: July 14, 2013, 04:29:58 PM »
All the engine fasteners are metric... try 13mm.
Logged
72 sedan 2.0, c-4 beater now hot 2.0, 4-speed
72 sedan 2.3, t-5, 8" running project
80 Bobcat hatchback 2.3, 4-spd, 97K

Offline waldo786

  • Pinto Full Member
  • ***
  • Posts: 236
  • FeedBack: +0/-0
  • Gender: Male

    • Total Badges: 5
    Badges: (View All)
    Tenth year Anniversary Topic Starter Poll Voter Windows User Fifth year Anniversary
Re: what socket for 2.3 head bolts
« Reply #3 on: July 14, 2013, 04:40:01 PM »
Thanks for the info, I did try the 9/16 and it was just slightly too big.  I'll have to check on the metric too, so thanks for the tip!
Logged

Offline Pinto5.0

  • Pinto Master
  • *****
  • Posts: 1974
  • FeedBack: +77/-0
  • Gender: Male
  • 80 hatch, 76 Wagon, 72 & 73 Sedans, 71 half hatch

    • Total Badges: 7
    Badges: (View All)
    Topic Starter Signature Poll Voter Mobile User Fifth year Anniversary Windows User 1000 Posts
Re: what socket for 2.3 head bolts
« Reply #4 on: July 14, 2013, 05:57:20 PM »
OK, wasn't sure. 1/2" & 13mm are interchangeabl e but use the one with the tightest grip. 13mm is a human hair smaller than 1/2" & only the best quality tools are that accurate.
Logged
'73 Sedan (I'll get to it)
'76 Wagon driver
'80 hatch(Restoring to be my son's 1st car)~Callisto
'71 half hatch (bucket list Pinto)~Ghost
'72 sedan 5.0/T5~Lemon Squeeze

Offline waldo786

  • Pinto Full Member
  • ***
  • Posts: 236
  • FeedBack: +0/-0
  • Gender: Male

    • Total Badges: 5
    Badges: (View All)
    Tenth year Anniversary Topic Starter Poll Voter Windows User Fifth year Anniversary
Re: what socket for 2.3 head bolts
« Reply #5 on: July 14, 2013, 06:24:34 PM »
Awesome, ordered a 13mm socket.  Hopefully it'll be here soon.  Very excited to get these old heads off and over to bo-port to get some work done on them. 
Logged
Pages: [1]   Go Up
« previous next »