Current Classifieds

Bumpers
Date: 07/06/2018 04:47 pm
instrument cluster,4sd trans crossmember,2.3 intake
Date: 08/26/2018 06:23 pm
Need '75 Pinto wagon front seat belt assembly housing
Date: 10/03/2018 10:46 pm
Lower Alternator bracket
Date: 08/26/2017 05:11 pm
'71,'72,or'73 small Ford v8 Pinto
Date: 01/23/2017 07:41 am
pinto floor mats??

Date: 01/11/2017 07:27 am
1971 yellow Pinto hatchback with limited edition chrome strips on rear door, 1600 cc engine

Date: 02/26/2017 03:22 pm
78 hatchback

Date: 03/12/2023 06:50 pm
1977 Pinto Cruizin Wagon

Date: 04/11/2024 04:13 pm
Front Body parts needed
Date: 02/09/2018 06:09 pm
78 hatchback

Date: 03/12/2023 06:50 pm
1973 FORD PINTO HOOD "F O R D" LETTERS
Date: 02/11/2020 12:09 am

« previous next »
Pages: [1]   Go Down

Author Topic: WHAT AM I MISSING  (Read 924 times)

0 Members and 1 Guest are viewing this topic.

Offline qq2ofus

  • Pinto Member
  • **
  • Posts: 52
  • FeedBack: +0/-2
  • Gender: Male
  • Mine was a six PINTO family ONCE

    • Total Badges: 5
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User Fifth year Anniversary
WHAT AM I MISSING
« on: April 14, 2017, 05:25:31 PM »
I am attempting to install a 302 into a 1977 cruiser, I have had the engine in and out 4 times today it refuses to go back far enough thru the tunnel to even put a bolt into frame mounts and the oil pan sits on the sway which tells me "not enough rear travel" am I supposed to remove the brace bars on the rear of the crossmember, My tranny is a 1977 MII BW 4 Speed, and the engine is rebuilt from a MII 

SIGNED  DAZED AND CONFUSED
Logged
I'm a member of the Pinto club, driving pintos is what I love  I don't like ol' pickup trucks, I'm a member of the Pinto Club

Offline Reeves1

  • Pinto Master
  • *****
  • Posts: 2158
  • FeedBack: +104/-0
  • Gender: Male
  • BAWS302

    • Total Badges: 6
    Badges: (View All)
    Tenth year Anniversary Topic Starter Signature Fifth year Anniversary Windows User 1000 Posts
Re: WHAT AM I MISSING
« Reply #1 on: April 15, 2017, 06:01:02 AM »
I only work on 72s, but reading stuff on this forum over the years, seems to me the sway bar cannot be used with a V8 swap ?
Also, if trying to use the OEM frame mounts, they are in the wrong location.
Logged

Offline dick1172762

  • Vintage Pinto Racer
  • PCCA Management Board
  • Pinto Sr. Master
  • ******
  • Posts: 2623
  • FeedBack: +362/-0
  • Gender: Male
  • I'm a llama!

    • Total Badges: 7
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User 1000 Posts Tenth year Anniversary Fifth year Anniversary
Re: WHAT AM I MISSING
« Reply #2 on: April 15, 2017, 08:42:59 AM »
As I remember there is some sort of smog fittings on the back side of one or both heads and must be removed. Know I had to on a v-8 rx-7 I built.
Logged
Its better to be a has-been, than a never was.

Offline qq2ofus

  • Pinto Member
  • **
  • Posts: 52
  • FeedBack: +0/-2
  • Gender: Male
  • Mine was a six PINTO family ONCE

    • Total Badges: 5
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User Fifth year Anniversary
Re: WHAT AM I MISSING
« Reply #3 on: April 15, 2017, 10:11:26 AM »
THANKS GUYS, I found it, I dropped the sway bar (pinto), and have to switch left to right mounts for more rear travel to drill frame mount holes, actually a person could do themselves better by having 2 left engine mounts, because it makes things closer to pinto factory the holes would be offset 3/4" instead of 1 5/16.........  I aqppreciate your answers though

Johnny
Logged
I'm a member of the Pinto club, driving pintos is what I love  I don't like ol' pickup trucks, I'm a member of the Pinto Club
Pages: [1]   Go Up
« previous next »