Current Classifieds

Automatic Wagon
Date: 06/14/2019 11:22 pm
1980 Pinto Wagon

Date: 02/29/2020 07:01 pm
Looking for Passenger side Inner Fender Apron
Date: 10/28/2018 08:45 am
Hoard of Pinto parts
Date: 12/17/2016 04:14 pm
Pinto interior parts for Cruisen / Rallye wagon
Date: 01/19/2021 03:56 pm
Need '75 Pinto wagon front seat belt assembly housing
Date: 10/03/2018 10:46 pm
2.3 carb intake

Date: 07/15/2020 09:25 pm
Drivers side door panel Orange
Date: 05/22/2018 02:27 pm
Chilton's Repair & Tune-up Guide 1971-1979 Pinto and Bobcat

Date: 03/06/2017 01:24 am
1974 Pinto Drivers door glass and parts

Date: 02/18/2017 05:52 pm
Electrical
Date: 03/29/2017 11:37 am
1976 Ford Pinto

Date: 07/16/2019 02:51 am

Author Topic: Visual differences between a '74 2.0 and 2.3 and manual transmission question  (Read 1686 times)

0 Members and 1 Guest are viewing this topic.

Offline russosborne

  • Pinto Master
  • *****
  • Posts: 2405
  • FeedBack: +47/-1
  • Gender: Male
  • Another Pinto Driver

  • Total Badges: 5
    Badges: (View All)
    Poll Voter Mobile User Topic Starter Signature 1000 Posts

Is it easy to tell just by looking which engine is in my 74 wagon? Getting it tomorrow, but I don't have a clue about that year yet, just know that both engines were available. Not sure if I have ever seen a 2.0 close up.
Or is this something I will need to decode the numbers on?

This car also has a manual trans. Sorry for the cluelessness, but would it be a 3 speed or a 4 speed? Trans is out of the car, can't play with the shifter to tell.  :o

I've got so much to learn.  :-[
Thanks,
Russ
In Glendale, Arizona

RIP Casey, Mallory, Abby, and Sadie. We miss you.

79 Pinto ESS fully caged fun car. In progress. 8inch 4.10 gears. 351C and a T5 waiting to go in.

Offline dennisofaz

  • Pinto Member
  • **
  • Posts: 98
  • FeedBack: +25/-0

  • Total Badges: 5
    Badges: (View All)
    Topic Starter Tenth year Anniversary Poll Voter Windows User Fifth year Anniversary
Hi Russ,


Yes it is easy to tell which engine you have.  If it is a 2.0 the distributor is at the very front of the engine and the exhaust manifold bolts are directly on top of each other on the 2.0 and the 2.3 exhaust manifold they are front to back.  also look for clues on the valve cover such as an emission sticker.


BR Denns

Offline russosborne

  • Pinto Master
  • *****
  • Posts: 2405
  • FeedBack: +47/-1
  • Gender: Male
  • Another Pinto Driver

  • Total Badges: 5
    Badges: (View All)
    Poll Voter Mobile User Topic Starter Signature 1000 Posts
Thanks.
Russ
In Glendale, Arizona

RIP Casey, Mallory, Abby, and Sadie. We miss you.

79 Pinto ESS fully caged fun car. In progress. 8inch 4.10 gears. 351C and a T5 waiting to go in.

Offline russosborne

  • Pinto Master
  • *****
  • Posts: 2405
  • FeedBack: +47/-1
  • Gender: Male
  • Another Pinto Driver

  • Total Badges: 5
    Badges: (View All)
    Poll Voter Mobile User Topic Starter Signature 1000 Posts
Well, according to an online vin decoder I found, this car came with a 2.0L. Built in San Jose.
I was hoping for a 2.3, but guess I can live with the 2.0 for now.
Russ
In Glendale, Arizona

RIP Casey, Mallory, Abby, and Sadie. We miss you.

79 Pinto ESS fully caged fun car. In progress. 8inch 4.10 gears. 351C and a T5 waiting to go in.

Offline 65ShelbyClone

  • Pinto Master
  • *****
  • Posts: 787
  • FeedBack: +139/-0
  • Soylent Green

  • Total Badges: 7
    Badges: (View All)
    Fifth year Anniversary Topic Starter Signature Poll Voter Mobile User Linux User Windows User
also look for clues on the valve cover such as an emission sticker.

The valve cover itself offers a subtle clue: the front of the 2.0 VC has two horizontal bolts going into the cam tower. 2.3s don't.

2.0s also have a fuel pump with bolts at the top and bottom. A 2.3's fuel pump has bolts at the front and rear.

Although you probably know what it is by now, I figure it may be helpful if someone else searches and finds this thread. ;)
'72 Runabout - 2.3T, T5, MegaSquirt-II, 8", 5-lugs, big brakes.
'68 Mustang - Built roller 302, Toploader, 9", etc.