Current Classifieds

1977 Left Side quarter panel
Date: 06/10/2019 04:16 pm
78 fender and hood
Date: 03/23/2021 01:07 pm
Odds and Ends 1976-77 Pinto Wagon

Date: 07/17/2019 05:23 pm
Center armrest for 1979 pinto . Possible anyone who makes them of has one for sale
Date: 08/13/2017 02:01 pm
Many Parts Listed Below
Date: 04/20/2018 11:15 am
WANTED: Dash, fender, hood, gauge bezel '73 Wagon
Date: 01/18/2017 05:35 pm
Clutch Pedals for 75to 80 Pinto
Date: 09/21/2018 11:35 am
Mini Mark IV one of 2 delux lg. sunroof models
Date: 06/18/2018 03:47 pm
13x6 minilite style wheels MAKE OFFER——NEED GONE

Date: 08/01/2018 01:17 pm
Lower Alternator bracket
Date: 08/26/2017 05:11 pm
1979 hatch needed
Date: 05/13/2018 08:52 pm
Looking for a few parts - TIA
Date: 02/19/2023 12:18 pm

Author Topic: Vin #'s  (Read 2177 times)

0 Members and 1 Guest are viewing this topic.

Offline Stuwil

  • Pinto Member
  • **
  • Posts: 73
  • FeedBack: +0/-0
  • Another Pinto Driver

  • Total Badges: 2
    Badges: (View All)
    Topic Starter Fifth year Anniversary
Vin #'s
« on: September 07, 2013, 06:58:03 PM »
I picked a 74 e150 with 351W in it. Only 39000 on the clock and I'm certain that is correct. I know the previous owner. Just got the engine and trans out. My question is what is the tranny? vin is   E14hha03293. (the zero could be an "Oh") Does that tell me anything? This transmission looks big. The differential looks way big too.
It has been sittin for over 20 years, would be cool to hear it run again.
Thanks for any help I can get

Offline jeremysdad

  • Pinto Sr. Member
  • ****
  • Posts: 405
  • FeedBack: +83/-6
  • Gender: Male
  • Restoring a Daily Driver

  • Total Badges: 4
    Badges: (View All)
    Fifth year Anniversary Topic Starter Poll Voter Windows User
Re: Vin #'s
« Reply #1 on: September 07, 2013, 07:22:40 PM »
Should be a c-6, if it's a van.

Offline Stuwil

  • Pinto Member
  • **
  • Posts: 73
  • FeedBack: +0/-0
  • Another Pinto Driver

  • Total Badges: 2
    Badges: (View All)
    Topic Starter Fifth year Anniversary
Re: Vin #'s
« Reply #2 on: September 07, 2013, 07:40:09 PM »
van   yes
ty

Offline righthandman

  • Pinto Member
  • **
  • Posts: 49
  • FeedBack: +3/-0
  • Gender: Male
  • Another Pinto Driver

  • Total Badges: 3
    Badges: (View All)
    Fifth year Anniversary Topic Starter Windows User
Re: Vin #'s
« Reply #3 on: September 07, 2013, 10:03:04 PM »
I'm not real sure that the trans was coded in the v.i.n. in 74, but every Ford built during the 70's had a code sticker on the drivers side door jamb. If you could get the trans code from that or get a picture or two (including one of the pan) from your trans. I'm sure someone here could tell you with certainty what you have.
I have a 71 E300 14' box van with a 302 and a C4 automatic. So they did use the C4 in some bigger trucks.
I think all the C4's unbolt from the bell housing, but the C6 does not. There casing is molded to bolt to certain size engines.

Offline Stuwil

  • Pinto Member
  • **
  • Posts: 73
  • FeedBack: +0/-0
  • Another Pinto Driver

  • Total Badges: 2
    Badges: (View All)
    Topic Starter Fifth year Anniversary
Re: Vin #'s
« Reply #4 on: September 08, 2013, 11:40:29 AM »
the bell housing and trans are all one piece
the only other number on the sticker is
F02197R1234
my feeling is it's a C6
any reason to keep it? Is it a better trans for a V8 swap?

Offline 71HANTO

  • Pinto Sr. Member
  • ****
  • Posts: 507
  • FeedBack: +108/-0
  • Gender: Male
    • Older site

  • Total Badges: 6
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User Webmaster Fifth year Anniversary
Re: Vin #'s
« Reply #5 on: September 08, 2013, 12:29:42 PM »
the bell housing and trans are all one piece
the only other number on the sticker is
F02197R1234
my feeling is it's a C6
any reason to keep it? Is it a better trans for a V8 swap?
The "Small Block C-6" is getting hard to find and can take some serious torque if in good shape. I took the FMX (heavy) trans out of my 69 351W Mustang and put in the lighter, stronger C-6. I'm putting out about 380ft lbs and there is little or no support for the FMX. There are people out there looking for your C-6.
 
71HANTO
 
"Life is a series of close ones...'til the last one"...cfpjr