Current Classifieds

Mirror
Date: 04/15/2020 01:42 pm
Need lower control arms for 1973 pinto
Date: 02/27/2017 10:10 pm
Deluxe Steering Wheel
Date: 10/16/2017 08:13 am
Looking for oil dipstick and tube 2.3L
Date: 11/23/2017 05:44 pm
Pinto Parts Windows & Windshield

Date: 11/12/2020 08:28 pm
oldskool787
Date: 02/12/2017 12:42 pm
78 wagon instrument y
Date: 04/30/2018 07:41 pm
4 speed pinto transmission

Date: 05/13/2021 05:29 pm
1980 Pinto w/ Trunk
Date: 08/10/2022 04:09 pm
WTB - 1979 Fan Shroud - D52E-8246-CIB
Date: 11/05/2020 06:32 pm
Wiring diagram Ignition switch 72 2.0 4 speed pinto wagon
Date: 12/31/2017 11:14 pm
1970-1973 British 4 Speed Manual; Parts or Whole
Date: 03/17/2019 03:57 am

« previous next »
Pages: [1]   Go Down

Author Topic: V8 C-4 Transmission help  (Read 2118 times)

0 Members and 1 Guest are viewing this topic.

Offline 351Bobcat

  • Pinto Driver
  • *
  • Posts: 4
  • FeedBack: +0/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 1
    Badges: (View All)
    Topic Starter
V8 C-4 Transmission help
« on: August 24, 2013, 10:52:16 PM »
I'm new to Fords and this forum.(I'm a Chevy guy) :-[ My 14 year old son bought a 1980 Bobcat with a 351 Windsor in it with a bad transmission. We did get a rebuilt C-4 transmission with it and the one that is in it is a automatic but not a C-4. I have been trying to do some research on what parts we need, flex plate, torque converter and anything else needed to get it in there. The transmission that we got with the car has the dipstick in the pan and as I understand or think I understand it takes a different torque converter than a case fill transmission. Any help on what we need to get this thing going would be great.
Logged

Offline slowride

  • Pinto Sr. Member
  • ****
  • Posts: 279
  • FeedBack: +18/-0

    • Total Badges: 3
    Badges: (View All)
    Topic Starter Windows User Fifth year Anniversary
Re: V8 C-4 Transmission help
« Reply #1 on: August 25, 2013, 08:38:45 PM »
Typically, a case fill C4 has a 164 tooth flywheel, and is probably a big bell C4 (bellhousing bolts to the case, not the pump). Post a pic of the pan, modulator, or servo to determine what you have.
Logged

Offline 351Bobcat

  • Pinto Driver
  • *
  • Posts: 4
  • FeedBack: +0/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 1
    Badges: (View All)
    Topic Starter
Re: V8 C-4 Transmission help
« Reply #2 on: August 25, 2013, 09:23:54 PM »
Some Pictures...
Logged

Offline HOSS429

  • Pinto Full Member
  • ***
  • Posts: 222
  • FeedBack: +22/-0
  • old ford guy

    • Total Badges: 5
    Badges: (View All)
    Tenth year Anniversary Fifth year Anniversary Topic Starter Poll Voter Windows User
Re: V8 C-4 Transmission help
« Reply #3 on: August 25, 2013, 09:29:53 PM »
what you have pictured is commonly called a C5  .. it usually comes behind 351 windsor motors in ford vans or trucks .. it has more clutches in the clutch drums .. it is a beafier trans ... 
Logged

Offline slowride

  • Pinto Sr. Member
  • ****
  • Posts: 279
  • FeedBack: +18/-0

    • Total Badges: 3
    Badges: (View All)
    Topic Starter Windows User Fifth year Anniversary
Re: V8 C-4 Transmission help
« Reply #4 on: August 25, 2013, 09:32:39 PM »
Big bell C4 with 164 tooth flexplate. Most likely post 1970. That matters because the input splines for converter are different than earlier. Count the splines on the input shaft and start surfing converter specs on Summit. 
Logged

Offline 351Bobcat

  • Pinto Driver
  • *
  • Posts: 4
  • FeedBack: +0/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 1
    Badges: (View All)
    Topic Starter
Re: V8 C-4 Transmission help
« Reply #5 on: August 25, 2013, 09:42:15 PM »
Already counted them... 26 spline.. Will this transmission fit in his Bobcat?
Logged

Offline slowride

  • Pinto Sr. Member
  • ****
  • Posts: 279
  • FeedBack: +18/-0

    • Total Badges: 3
    Badges: (View All)
    Topic Starter Windows User Fifth year Anniversary
Re: V8 C-4 Transmission help
« Reply #6 on: August 25, 2013, 09:49:03 PM »
You will need to massage the firewall and trans tunnel.
Logged

Offline slowride

  • Pinto Sr. Member
  • ****
  • Posts: 279
  • FeedBack: +18/-0

    • Total Badges: 3
    Badges: (View All)
    Topic Starter Windows User Fifth year Anniversary
Re: V8 C-4 Transmission help
« Reply #7 on: August 25, 2013, 09:54:05 PM »
This will help you narrow it down a bit more.

"The early model C4 (1964–1969) used a .788-inch 24-spline input shaft, which was upgraded in 1970 to 26-spline and .839-inch. The upgrade also included a matching clutch hub of 26-spline. In 1971, Ford went to a 26/24-spline input shaft, meaning the torque-converter side is 26-spline and the clutch hub is 24-spline."
Logged

Offline 351Bobcat

  • Pinto Driver
  • *
  • Posts: 4
  • FeedBack: +0/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 1
    Badges: (View All)
    Topic Starter
Re: V8 C-4 Transmission help
« Reply #8 on: August 26, 2013, 10:55:24 PM »
The small shaft that pulls out has 26 splines and the large shaft has 32 splines
Logged

Offline slowride

  • Pinto Sr. Member
  • ****
  • Posts: 279
  • FeedBack: +18/-0

    • Total Badges: 3
    Badges: (View All)
    Topic Starter Windows User Fifth year Anniversary
Re: V8 C-4 Transmission help
« Reply #9 on: August 26, 2013, 11:55:41 PM »
26 spline is what you'll need. Make sure the converter bolt pattern is correct for a 164 flexplate, and if it's an early 351, the flexplate is a 28oz imbalance. Tons of good info at TCI.
http://www.tciauto.com/tc/c4-bellhousings
Logged
Pages: [1]   Go Up
« previous next »