Current Classifieds

71-71 speedo cable
Date: 07/31/2021 09:04 pm
Brake rotors
Date: 03/24/2017 09:02 pm
Chilton's Repair & Tune-up Guide 1971-1979 Pinto and Bobcat

Date: 03/06/2017 01:24 am
1975 rear end, 8 inch, drum brakes, and axles, 3.4 gear.

Date: 11/08/2019 10:01 am
Wanted 1971-73 pinto 2.0 4 speed manual transmission
Date: 03/06/2019 06:40 pm
KYB shocks

Date: 02/08/2017 07:09 pm
Front sway bar frame brackets
Date: 07/13/2017 01:05 am
Center armrest for 1979 pinto . Possible anyone who makes them of has one for sale
Date: 08/13/2017 02:01 pm
NOS Sedan decklid

Date: 10/23/2019 11:51 am
1973 Bobcat Cruzin Wagon for Sale $4000 obo

Date: 04/13/2018 11:30 am
Wanted early pinto
Date: 10/03/2019 02:42 pm
1978 pinto brake booster needed.
Date: 04/07/2021 06:12 pm

Author Topic: v6 issues  (Read 1373 times)

0 Members and 1 Guest are viewing this topic.

Offline krazi

  • Pinto Sr. Member
  • ****
  • Posts: 417
  • FeedBack: +3/-0
  • Gender: Male
  • Another Bobcat Driver

  • Total Badges: 7
    Badges: (View All)
    Mobile User Topic Starter Signature Poll Voter Tenth year Anniversary Windows User Fifth year Anniversary
v6 issues
« on: July 20, 2016, 09:57:28 PM »
did a cam and engine swap last summer. v6 to v6, 2800. the "newer" engine gets better oil pressure, but for some reason it's blowing motor oil out the tail pipes. (plural, dual exhaust) it only happens over 2100 rpm, and I think it might have fouled the plugs. now that I have some time to get it going again, what could it be that I goofed on? if it was a bad gasket cleaning, then it would be water and antifreeze, right? someone told me it could be the valve rubbers in the top of the engine. any help would be appreciated.
yeah, I'm Krazi!

Offline phils toys

  • Pinto Master
  • *****
  • Posts: 1405
  • FeedBack: +34/-0
  • Gender: Male
  • 76 Bobcat Wagon fun for the whole family
    • phils toys

  • Total Badges: 11
    Badges: (View All)
    Topic Starter Signature Poll Voter Tenth year Anniversary Photographer Apple User Linux User Mobile User 1000 Posts Webmaster Fifth year Anniversary
Re: v6 issues
« Reply #1 on: July 21, 2016, 01:50:33 PM »
I would agree it is valve related
2006, 07,08 ,10 Carlisle 3rd stock pinto 4 years same place
2007 PCCA East Regional Best Wagon
2008 CAHS Prom Coolest Ride
2011,2014 pinto stampede

Offline 74 PintoWagon

  • Pinto Sr. Master
  • ******
  • Posts: 3105
  • FeedBack: +540/-0
  • Gender: Male
  • Another Pinto Driver

  • Total Badges: 5
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User 1000 Posts
Re: v6 issues
« Reply #2 on: July 22, 2016, 07:43:27 AM »
I didn't actually have liquid oil coming out the pipe but it was smoking continuously, valve seals were shot in fact some were just laying on the head, put a new set on and smoke was all gone and didn't use a drop of oil.
Art
65 Falcon 2DR 200 IL6 with C4.

Offline krazi

  • Pinto Sr. Member
  • ****
  • Posts: 417
  • FeedBack: +3/-0
  • Gender: Male
  • Another Bobcat Driver

  • Total Badges: 7
    Badges: (View All)
    Mobile User Topic Starter Signature Poll Voter Tenth year Anniversary Windows User Fifth year Anniversary
Re: v6 issues
« Reply #3 on: July 26, 2016, 08:41:57 PM »
would it be possible to change the valve seals without pulling the heads? money's kinda tight right now.
yeah, I'm Krazi!

Offline 74 PintoWagon

  • Pinto Sr. Master
  • ******
  • Posts: 3105
  • FeedBack: +540/-0
  • Gender: Male
  • Another Pinto Driver

  • Total Badges: 5
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User 1000 Posts
Re: v6 issues
« Reply #4 on: July 26, 2016, 10:13:41 PM »
Yep very easy to do, just need a hand compressor for the springs and a way to hold the valve up, myself I like to use air been doing it for 30+yrs, but there are other ways if you don't have air whatever will hold the valve up, just make sure the piston is at the top..
Art
65 Falcon 2DR 200 IL6 with C4.

Offline Wittsend

  • Pinto Master
  • *****
  • Posts: 2496
  • FeedBack: +241/-0

  • Total Badges: 8
    Badges: (View All)
    Tenth year Anniversary Mobile User Topic Starter Poll Voter 1000 Posts Linux User Windows User Fifth year Anniversary
Re: v6 issues
« Reply #5 on: July 27, 2016, 12:32:18 PM »
And..., if you lack a sufficient compressor just set the piston at top dead center and feed thin rope through the spark plug hole to fill the combustion chamber and keep the valve from dropping.  Hopefully you have a manual transmission and can lock the engine from turning. Otherwise use a socket/bar on the crank pulley to counter the potential crank rotation. Ideally at TDC pushing on the valve spring won't cause the crank to rotate, but when it does.... yikes!

I don't mean to scare you, only caution you. I have used the thin rope method without incident.  Sometimes pushing on the valve spring compresses the rope and the valve will drop slightly. In this case I've, pulled the valve up, use a rubberband looped over the valve stem to hold it and then cut/broken the rubberband after installation.