Current Classifieds

'76 Wagon Driver Side Rear Interior Panel
Date: 11/11/2019 04:49 pm
Clutch pedal needed
Date: 01/11/2024 06:31 am
1971 Pinto Do It Yourself Manual

Date: 03/06/2017 01:19 am
Esslinger 2.0 intake
Date: 03/06/2017 11:58 am
1978 fuel sendng unit
Date: 05/27/2020 09:54 am
Looking for 1.6 exhaust manifold heat shield, front license plate bracket
Date: 11/04/2018 02:34 am
79 pinto front,rear alum bumpers

Date: 07/17/2018 09:49 pm
13" Style Steel Trim Rings

Date: 10/09/2020 10:35 pm
parting out 1975 & 80 pintos
Date: 04/28/2018 04:12 pm
Rally spoiler wanted
Date: 05/04/2017 01:32 pm
parts needed
Date: 02/20/2017 07:58 am
73 actuator for heater blend door
Date: 09/19/2019 04:43 pm

Author Topic: v6 issues  (Read 1371 times)

0 Members and 1 Guest are viewing this topic.

Offline krazi

  • Pinto Sr. Member
  • ****
  • Posts: 417
  • FeedBack: +3/-0
  • Gender: Male
  • Another Bobcat Driver

  • Total Badges: 7
    Badges: (View All)
    Mobile User Topic Starter Signature Poll Voter Tenth year Anniversary Windows User Fifth year Anniversary
v6 issues
« on: July 20, 2016, 09:57:28 PM »
did a cam and engine swap last summer. v6 to v6, 2800. the "newer" engine gets better oil pressure, but for some reason it's blowing motor oil out the tail pipes. (plural, dual exhaust) it only happens over 2100 rpm, and I think it might have fouled the plugs. now that I have some time to get it going again, what could it be that I goofed on? if it was a bad gasket cleaning, then it would be water and antifreeze, right? someone told me it could be the valve rubbers in the top of the engine. any help would be appreciated.
yeah, I'm Krazi!

Offline phils toys

  • Pinto Master
  • *****
  • Posts: 1405
  • FeedBack: +34/-0
  • Gender: Male
  • 76 Bobcat Wagon fun for the whole family
    • phils toys

  • Total Badges: 11
    Badges: (View All)
    Topic Starter Signature Poll Voter Tenth year Anniversary Photographer Apple User Linux User Mobile User 1000 Posts Webmaster Fifth year Anniversary
Re: v6 issues
« Reply #1 on: July 21, 2016, 01:50:33 PM »
I would agree it is valve related
2006, 07,08 ,10 Carlisle 3rd stock pinto 4 years same place
2007 PCCA East Regional Best Wagon
2008 CAHS Prom Coolest Ride
2011,2014 pinto stampede

Offline 74 PintoWagon

  • Pinto Sr. Master
  • ******
  • Posts: 3105
  • FeedBack: +540/-0
  • Gender: Male
  • Another Pinto Driver

  • Total Badges: 5
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User 1000 Posts
Re: v6 issues
« Reply #2 on: July 22, 2016, 07:43:27 AM »
I didn't actually have liquid oil coming out the pipe but it was smoking continuously, valve seals were shot in fact some were just laying on the head, put a new set on and smoke was all gone and didn't use a drop of oil.
Art
65 Falcon 2DR 200 IL6 with C4.

Offline krazi

  • Pinto Sr. Member
  • ****
  • Posts: 417
  • FeedBack: +3/-0
  • Gender: Male
  • Another Bobcat Driver

  • Total Badges: 7
    Badges: (View All)
    Mobile User Topic Starter Signature Poll Voter Tenth year Anniversary Windows User Fifth year Anniversary
Re: v6 issues
« Reply #3 on: July 26, 2016, 08:41:57 PM »
would it be possible to change the valve seals without pulling the heads? money's kinda tight right now.
yeah, I'm Krazi!

Offline 74 PintoWagon

  • Pinto Sr. Master
  • ******
  • Posts: 3105
  • FeedBack: +540/-0
  • Gender: Male
  • Another Pinto Driver

  • Total Badges: 5
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User 1000 Posts
Re: v6 issues
« Reply #4 on: July 26, 2016, 10:13:41 PM »
Yep very easy to do, just need a hand compressor for the springs and a way to hold the valve up, myself I like to use air been doing it for 30+yrs, but there are other ways if you don't have air whatever will hold the valve up, just make sure the piston is at the top..
Art
65 Falcon 2DR 200 IL6 with C4.

Offline Wittsend

  • Pinto Master
  • *****
  • Posts: 2496
  • FeedBack: +241/-0

  • Total Badges: 8
    Badges: (View All)
    Tenth year Anniversary Mobile User Topic Starter Poll Voter 1000 Posts Linux User Windows User Fifth year Anniversary
Re: v6 issues
« Reply #5 on: July 27, 2016, 12:32:18 PM »
And..., if you lack a sufficient compressor just set the piston at top dead center and feed thin rope through the spark plug hole to fill the combustion chamber and keep the valve from dropping.  Hopefully you have a manual transmission and can lock the engine from turning. Otherwise use a socket/bar on the crank pulley to counter the potential crank rotation. Ideally at TDC pushing on the valve spring won't cause the crank to rotate, but when it does.... yikes!

I don't mean to scare you, only caution you. I have used the thin rope method without incident.  Sometimes pushing on the valve spring compresses the rope and the valve will drop slightly. In this case I've, pulled the valve up, use a rubberband looped over the valve stem to hold it and then cut/broken the rubberband after installation.