11 Guests, 0 Users

« previous next »
Pages: [1]   Go Down

Author Topic: V6 bypass hose inlet  (Read 1284 times)

0 Members and 1 Guest are viewing this topic.

Offline chrisa850

  • Pinto Member
  • **
  • Posts: 51
  • FeedBack: +3/-0

    • Total Badges: 5
    Badges: (View All)
    Tenth year Anniversary Topic Starter Photographer Windows User Fifth year Anniversary
V6 bypass hose inlet
« on: June 21, 2014, 08:46:25 PM »
Does anyone have a source or part number for the 2800cc V6 bypass hose lower rear water inlet? It's the component labeled 8592 in the attached drawing. It doesn't seem to follow the standard D4/D5/D6FZ-8592xx part number.
Logged

Offline bbobcat75

  • Pinto Master
  • *****
  • Posts: 1032
  • FeedBack: +71/-0
  • Gender: Male

    • Total Badges: 8
    Badges: (View All)
    Topic Starter Signature Poll Voter 1000 Posts Apple User Mobile User Windows User Fifth year Anniversary
Re: V6 bypass hose inlet
« Reply #1 on: June 22, 2014, 12:57:16 PM »
I don't have a part number took it to a local parts store and just matched up a similar hose. Not a huge help but a thought! If you don't have the hose then hmmm hopefully some one else can shed some light here!
Logged
1975 mercury bobcat 2.8 auto
1978 mercury bobcat wagon 2.3l - soon to have a 88 tc drive line
1975 ford pinto - drag car - 2.3l w/t5 trans - project car

Offline enzo

  • Pinto Member
  • **
  • Posts: 74
  • FeedBack: +0/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 4
    Badges: (View All)
    Fifth year Anniversary Topic Starter Poll Voter Windows User
Re: V6 bypass hose inlet
« Reply #2 on: June 22, 2014, 01:01:00 PM »
Napa part #7633.
Logged

Offline chrisa850

  • Pinto Member
  • **
  • Posts: 51
  • FeedBack: +3/-0

    • Total Badges: 5
    Badges: (View All)
    Tenth year Anniversary Topic Starter Photographer Windows User Fifth year Anniversary
Re: V6 bypass hose inlet
« Reply #3 on: June 22, 2014, 02:46:07 PM »
I have the bypass hose. The part I'm looking for is the aluminum inlet itself. part 8592 in the pictorial.

Logged

Offline bbobcat75

  • Pinto Master
  • *****
  • Posts: 1032
  • FeedBack: +71/-0
  • Gender: Male

    • Total Badges: 8
    Badges: (View All)
    Topic Starter Signature Poll Voter 1000 Posts Apple User Mobile User Windows User Fifth year Anniversary
Re: V6 bypass hose inlet
« Reply #4 on: June 22, 2014, 09:18:11 PM »
your looking for the thermostat housing! good luck being alum. and a 2.8 part only will be a hard part to find that is good and not rotted out!! good luck - check the bay!! ebay
Logged
1975 mercury bobcat 2.8 auto
1978 mercury bobcat wagon 2.3l - soon to have a 88 tc drive line
1975 ford pinto - drag car - 2.3l w/t5 trans - project car

Offline enzo

  • Pinto Member
  • **
  • Posts: 74
  • FeedBack: +0/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 4
    Badges: (View All)
    Fifth year Anniversary Topic Starter Poll Voter Windows User
Re: V6 bypass hose inlet
« Reply #5 on: June 23, 2014, 05:01:07 PM »
Sorry, I didn't read the post completely.  I have one that is usable if you can get the broken bolt end out of it.
Looks like the is enough material to carefully drill out the bolt and re-thread.
Logged
Pages: [1]   Go Up
« previous next »