Current Classifieds

72 Pinto racecar, 2.3 ARCA engine, Quaife trans
Date: 01/10/2022 03:41 pm
Pinto in Maine for sail...solid body

Date: 03/07/2017 07:03 pm
New cam

Date: 01/23/2017 05:11 pm
'78 Pinto Windshield Trim
Date: 05/09/2017 10:46 am
1978 FORD PINTO PONY FOR SALE 17.000 MILES !!!!!!!!!!!!

Date: 06/25/2021 12:59 am
77 Caliper Bolt
Date: 08/21/2018 04:02 pm
72' hatchback parts wanted
Date: 08/25/2019 02:57 am
1977 Pinto Cruising Wagon FOR SALE

Date: 08/20/2017 01:34 pm
1980 Pinto taillights
Date: 12/26/2017 03:48 pm
79 pinto small parts
Date: 04/24/2019 03:16 pm
1971 Pinto

Date: 03/04/2017 11:28 pm
'79 4 speed manual shifter needed
Date: 07/30/2018 04:32 pm

« previous next »
Pages: [1]   Go Down

Author Topic: using 8" rear end with factory parking brake cables.  (Read 1544 times)

0 Members and 1 Guest are viewing this topic.

Offline dennisofaz

  • Pinto Member
  • **
  • Posts: 98
  • FeedBack: +25/-0

    • Total Badges: 5
    Badges: (View All)
    Topic Starter Tenth year Anniversary Poll Voter Windows User Fifth year Anniversary
using 8" rear end with factory parking brake cables.
« on: May 20, 2013, 05:53:28 PM »
Hi, i recently purchased an 8" Mustang II rear end and i have a question.  Will the parking brake cable from a 6 3/4 rear end fit properly into the 8" rear backing plates?  Many years ago did this swap and ran into this issue if the cable mounting hole being too big for the Pinto cable.  If they do not fit then can I get Mustang II cables and make the transition at the parking break main cable? 


Dennis
Logged

Offline Pinto5.0

  • Pinto Master
  • *****
  • Posts: 1974
  • FeedBack: +77/-0
  • Gender: Male
  • 80 hatch, 76 Wagon, 72 & 73 Sedans, 71 half hatch

    • Total Badges: 7
    Badges: (View All)
    Topic Starter Signature Poll Voter Mobile User Fifth year Anniversary Windows User 1000 Posts
Re: using 8" rear end with factory parking brake cables.
« Reply #1 on: May 20, 2013, 07:14:15 PM »
I was always told it's the same cable regardless of which rear you run.
Logged
'73 Sedan (I'll get to it)
'76 Wagon driver
'80 hatch(Restoring to be my son's 1st car)~Callisto
'71 half hatch (bucket list Pinto)~Ghost
'72 sedan 5.0/T5~Lemon Squeeze

Offline Wittsend

  • Pinto Sr. Master
  • ******
  • Posts: 2501
  • FeedBack: +241/-0

    • Total Badges: 8
    Badges: (View All)
    Tenth year Anniversary Mobile User Topic Starter Poll Voter 1000 Posts Linux User Windows User Fifth year Anniversary
Re: using 8" rear end with factory parking brake cables.
« Reply #2 on: May 20, 2013, 08:13:55 PM »
I can't remember what I did when I performed my 8" swap.   I can tell you that although the rear drums have the same brake diameter, the center hole for the 6-3/4" is too small.

Tom
Logged

Offline dennisofaz

  • Pinto Member
  • **
  • Posts: 98
  • FeedBack: +25/-0

    • Total Badges: 5
    Badges: (View All)
    Topic Starter Tenth year Anniversary Poll Voter Windows User Fifth year Anniversary
Re: using 8" rear end with factory parking brake cables.
« Reply #3 on: May 20, 2013, 09:42:27 PM »
Thanks Guys!  I found MII & Pinto parking brake cables at Rockauto and if need be I can use the MII cables into the rear end and make the connection at the parking brake.


The MII cables are 104 3/4" long and the Pinto is 110" long so i would have to extend the pull cable ~3" to reach the shorter MII cable.


Dennis
Logged
Pages: [1]   Go Up
« previous next »