Current Classifieds

1980 Ford Pinto For Sale

Date: 07/01/2018 03:21 pm
71,72 Pinto Door Panels

Date: 06/17/2018 08:27 pm
1976-1980 A/C condensor

Date: 09/21/2020 10:43 pm
Misc. Pinto parts

Date: 11/09/2019 04:25 pm
1977 pinto rear bumper
Date: 04/19/2021 11:57 am
Ford Speedometer Hall-Effect sensor with 6 foot speedometer cable

Date: 12/30/2022 01:30 pm
1973 Pinto hatchback for sale

Date: 11/13/2023 11:30 am
Rare parts for sale
Date: 09/10/2018 08:38 am
Mustang II C4 Transmission
Date: 07/28/2017 06:26 am
SVO SWAP
Date: 03/15/2018 03:12 am
1979 pinto
Date: 04/19/2018 02:02 am
4:11 gears for 6.75 Make offer...NEED GONE

Date: 08/01/2018 01:27 pm

Author Topic: uneven fuel distribution in 2.0  (Read 449 times)

0 Members and 1 Guest are viewing this topic.

Offline LongTimeFordMan

  • PCCA VIP
  • Pinto Sr. Member
  • ***
  • Posts: 450
  • FeedBack: +182/-0
  • Gender: Male
  • 1973 Red Pinto Wagon

  • Total Badges: 6
    Badges: (View All)
    Fifth year Anniversary Topic Starter Signature Windows User Linux User Mobile User
uneven fuel distribution in 2.0
« on: October 17, 2020, 01:13:01 PM »
hi..
has anyone experienced uneven fuel.distribut ion between cyllenders in a 2.0?

I installed a new factory jetted weber DGV on my 73 wagon and drive moderately daily. manual choke always full open except to start.

Stock rebuild, 5000 miles, stock cam and cyls 2 and 3 run rich but 1 and 4 lean.

no vacuum leaks, compression 170 +- 10 on all cyls.all.ign wires good. pertronix flame.thrower ign.

car runs ok,  16-18 MPG in town 23-26 on the highway.

the weber primary and secondary are reversed from the original 5200. i suspect possibly just the manifold design?
Red 1973 pinto wagon DD, SoCal desert car, Factory 4 speed, 3.40 gears, Stock engine, 14" rims and tires, 60 K original miles

Offline Wittsend

  • Pinto Master
  • *****
  • Posts: 2499
  • FeedBack: +241/-0

  • Total Badges: 8
    Badges: (View All)
    Tenth year Anniversary Mobile User Topic Starter Poll Voter 1000 Posts Linux User Windows User Fifth year Anniversary
Re: uneven fuel distribution in 2.0
« Reply #1 on: October 18, 2020, 11:52:23 AM »
Are the primaries on the inside or outside. If inside then likely yes the design might be the issue as the air/fuel would follow the shortest path and 1-4 cause the flow to need to pull away to the outer runners. What happened with the SU's?

Offline LongTimeFordMan

  • PCCA VIP
  • Pinto Sr. Member
  • ***
  • Posts: 450
  • FeedBack: +182/-0
  • Gender: Male
  • 1973 Red Pinto Wagon

  • Total Badges: 6
    Badges: (View All)
    Fifth year Anniversary Topic Starter Signature Windows User Linux User Mobile User
Re: uneven fuel distribution in 2.0
« Reply #2 on: October 18, 2020, 06:12:32 PM »
the primary is on the inside toward the engine...since the weber is reverse of the holley 5200

The SUs worked well but i had the.same.probl em.with 2,3 running rich and 1 ,4 lean.with the new manifold. the other one with the plenum had better distribution

i think it was charge robbing..

im re doing the new one to have a plenum
Red 1973 pinto wagon DD, SoCal desert car, Factory 4 speed, 3.40 gears, Stock engine, 14" rims and tires, 60 K original miles