Current Classifieds

Pinto sales literature / magazine ads/ owners manuals
Date: 03/21/2017 07:47 pm
Looking for fan shroud for 72' Pinto 1.6
Date: 04/13/2017 04:56 am
1978 fuel sendng unit
Date: 05/27/2020 09:54 am
'79 4 speed manual shifter needed
Date: 07/30/2018 04:32 pm
'76 Wagon Driver Side Rear Interior Panel
Date: 11/11/2019 04:49 pm
Squire trim
Date: 03/28/2018 10:11 am
1980 Pinto Parts

Date: 08/05/2020 04:20 pm
Clutch Cable Needed
Date: 04/03/2017 11:03 pm
Looking for Radiator and gas tank
Date: 10/24/2018 07:41 am
Bumpers
Date: 07/06/2018 04:47 pm
1971 2.0 valve cover
Date: 01/25/2019 07:09 pm
78-80 Windshield
Date: 10/29/2021 03:11 pm

« previous next »
Pages: [1]   Go Down

Author Topic: uneven fuel distribution in 2.0  (Read 450 times)

0 Members and 1 Guest are viewing this topic.

Offline LongTimeFordMan

  • PCCA VIP
  • Pinto Sr. Member
  • ***
  • Posts: 450
  • FeedBack: +182/-0
  • Gender: Male
  • 1973 Red Pinto Wagon

    • Total Badges: 6
    Badges: (View All)
    Fifth year Anniversary Topic Starter Signature Windows User Linux User Mobile User
uneven fuel distribution in 2.0
« on: October 17, 2020, 01:13:01 PM »
hi..
has anyone experienced uneven fuel.distribut ion between cyllenders in a 2.0?

I installed a new factory jetted weber DGV on my 73 wagon and drive moderately daily. manual choke always full open except to start.

Stock rebuild, 5000 miles, stock cam and cyls 2 and 3 run rich but 1 and 4 lean.

no vacuum leaks, compression 170 +- 10 on all cyls.all.ign wires good. pertronix flame.thrower ign.

car runs ok,  16-18 MPG in town 23-26 on the highway.

the weber primary and secondary are reversed from the original 5200. i suspect possibly just the manifold design?
Logged
Red 1973 pinto wagon DD, SoCal desert car, Factory 4 speed, 3.40 gears, Stock engine, 14" rims and tires, 60 K original miles

Offline Wittsend

  • Pinto Master
  • *****
  • Posts: 2499
  • FeedBack: +241/-0

    • Total Badges: 8
    Badges: (View All)
    Tenth year Anniversary Mobile User Topic Starter Poll Voter 1000 Posts Linux User Windows User Fifth year Anniversary
Re: uneven fuel distribution in 2.0
« Reply #1 on: October 18, 2020, 11:52:23 AM »
Are the primaries on the inside or outside. If inside then likely yes the design might be the issue as the air/fuel would follow the shortest path and 1-4 cause the flow to need to pull away to the outer runners. What happened with the SU's?
Logged

Offline LongTimeFordMan

  • PCCA VIP
  • Pinto Sr. Member
  • ***
  • Posts: 450
  • FeedBack: +182/-0
  • Gender: Male
  • 1973 Red Pinto Wagon

    • Total Badges: 6
    Badges: (View All)
    Fifth year Anniversary Topic Starter Signature Windows User Linux User Mobile User
Re: uneven fuel distribution in 2.0
« Reply #2 on: October 18, 2020, 06:12:32 PM »
the primary is on the inside toward the engine...since the weber is reverse of the holley 5200

The SUs worked well but i had the.same.probl em.with 2,3 running rich and 1 ,4 lean.with the new manifold. the other one with the plenum had better distribution

i think it was charge robbing..

im re doing the new one to have a plenum
Logged
Red 1973 pinto wagon DD, SoCal desert car, Factory 4 speed, 3.40 gears, Stock engine, 14" rims and tires, 60 K original miles
Pages: [1]   Go Up
« previous next »