Current Classifieds

Bell housing
Date: 08/23/2017 05:41 am
Front sump oil pan
Date: 01/02/2017 06:54 pm
FLOOR PANS
Date: 06/12/2020 07:24 pm
79 pinto driveshaft
Date: 08/18/2018 02:03 pm
need 1978 pinto guage cluster
Date: 03/07/2021 07:35 am
1600 CC WATER PUMP
Date: 06/02/2018 09:13 am
72 Turbo Pinto "Hot Rod" rebuild
Date: 08/09/2018 11:09 am
WTB: Factory air cleaner and fan shroud 1971 2.0
Date: 02/05/2020 11:06 am
WANTED: Skinny Rear Bumper w/o guards for '71 or '72 Pinto Coupe
Date: 04/24/2018 11:45 am
Wanted: Oil Breather F0ZZ6A485A "87-8 from 2.3L Turbo
Date: 08/06/2021 02:23 pm
Seeking reveal molding for driver's door for a 1980 Squire Wagon
Date: 11/08/2020 02:10 pm
1980 Pinto w/ Trunk
Date: 08/10/2022 04:09 pm

« previous next »
Pages: [1]   Go Down

Author Topic: Transmission shifting  (Read 1046 times)

0 Members and 1 Guest are viewing this topic.

Offline sedandelivery

  • Pinto Sr. Member
  • ****
  • Posts: 460
  • FeedBack: +30/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 5
    Badges: (View All)
    Tenth year Anniversary Topic Starter Poll Voter Fifth year Anniversary Windows User
Transmission shifting
« on: August 08, 2015, 07:31:07 PM »
I have my Sedandelivery back and was driving it all over the place today. It runs soo nicely. Why does the transmission on this car wind out nicely, but on the Bobcat it upshifts quickly and impedes acceleration. Any ideas? The SD doesn't have a cat, the Bobcat does, do they impede acceleration a lot?
Logged

Offline HOSS429

  • Pinto Full Member
  • ***
  • Posts: 222
  • FeedBack: +22/-0
  • old ford guy

    • Total Badges: 5
    Badges: (View All)
    Tenth year Anniversary Fifth year Anniversary Topic Starter Poll Voter Windows User
Re: Transmission shifting
« Reply #1 on: August 08, 2015, 08:38:30 PM »
you should have an adjustable shift modulator on the bobcat .. if so you can adjust it so it will shift later .. if not you can get one .. that is if you have the C4 trans .. i dont know about other type trans ... pull the short rubber hose off the shift  modulator    and see if it has a flat head adjusting screw inside the vacuum hole .. if so take a very small flat  head screw driver and screw the adjusting screw in one turn and try it .. the more you screw it in the longer it will take to shift  ..
Logged

Offline pinto_one

  • Pinto Master
  • *****
  • Posts: 1008
  • FeedBack: +70/-0
  • Gender: Male
  • Pinto-One

    • Total Badges: 10
    Badges: (View All)
    1000 Posts Photographer Tenth year Anniversary Topic Starter Signature Poll Voter Mobile User Apple User Windows User Fifth year Anniversary
Re: Transmission shifting
« Reply #2 on: August 08, 2015, 10:21:04 PM »
If it's a c-3 you have to get different lengths of modulator rods to adjust the shift points , they usely come with a shift kit for that trans , made by transgo ,
T
Logged
76 Pinto sedan V6 , 79 pinto cruiser wagon V6 soon to be diesel or 4.0
Pages: [1]   Go Up
« previous next »