Current Classifieds

V8 rear end
Date: 04/12/2018 10:57 am
WTB. Seat cover or material LFront
Date: 07/01/2019 03:17 pm
Looking for Plastic? sloping headlight buckets for 77/78
Date: 06/19/2018 03:58 pm
73 2.0 Timing Crank Gear & Woodruff key WANTED
Date: 09/01/2017 07:52 am
Automatic transmission
Date: 02/13/2021 02:52 pm
74 pinto
Date: 09/11/2016 06:32 pm
77 Caliper Bolt
Date: 08/21/2018 04:02 pm
Squire trim
Date: 03/28/2018 10:11 am
76 pinto sedan sbc/bbc project for sale $1700 obo

Date: 03/27/2017 10:07 pm
2.3 carb intake

Date: 07/15/2020 09:25 pm
Sunroof shade
Date: 06/19/2019 01:33 pm
1980 pinto/bobcat floors
Date: 07/24/2018 08:11 pm

« previous next »
Pages: [1]   Go Down

Author Topic: transmission lines  (Read 2729 times)

0 Members and 1 Guest are viewing this topic.

Offline natedawg15

  • Pinto Member
  • **
  • Posts: 11
  • FeedBack: +0/-0
  • Another Pinto Driver

    • Total Badges: 1
    Badges: (View All)
    Topic Starter
transmission lines
« on: March 09, 2014, 03:14:57 PM »
Hello again guys my trans lines were  cut at the trans.  There seems to be three lines does anyone know which ones do what so when I hook them to a cooler it does not explode?  Thanks again.
Logged

Offline 74 PintoWagon

  • Pinto Sr. Master
  • ******
  • Posts: 3105
  • FeedBack: +540/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 5
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User 1000 Posts
Re: transmission lines
« Reply #1 on: March 09, 2014, 07:36:38 PM »
The two that goes into the case itself are oil, the other one would be from the modulator that is vacuum.
Logged
Art
65 Falcon 2DR 200 IL6 with C4.

Offline amc49

  • PCCA VIP
  • Pinto Master
  • ***
  • Posts: 1256
  • FeedBack: +242/-1
  • Another Pinto Driver

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Poll Voter Windows User 1000 Posts
Re: transmission lines
« Reply #2 on: March 10, 2014, 02:47:18 AM »
If just using an air cooler and not going through radiator then the two oil lines do not matter, they can go to cooler either way, the direction of flow does not matter unless you have a specific directional flow cooler, most are not.
Logged

Offline natedawg15

  • Pinto Member
  • **
  • Posts: 11
  • FeedBack: +0/-0
  • Another Pinto Driver

    • Total Badges: 1
    Badges: (View All)
    Topic Starter
Re: transmission lines
« Reply #3 on: March 11, 2014, 07:19:37 PM »
Thank you that was very helpfull now where does the vaccume line hook up?  Can I run without it hooked up?
Logged

Offline 74 PintoWagon

  • Pinto Sr. Master
  • ******
  • Posts: 3105
  • FeedBack: +540/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 5
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User 1000 Posts
Re: transmission lines
« Reply #4 on: March 11, 2014, 09:22:37 PM »
The vacuum controls shift points it goes from modulator to manifold vacuum..

Logged
Art
65 Falcon 2DR 200 IL6 with C4.

Offline amc49

  • PCCA VIP
  • Pinto Master
  • ***
  • Posts: 1256
  • FeedBack: +242/-1
  • Another Pinto Driver

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Poll Voter Windows User 1000 Posts
Re: transmission lines
« Reply #5 on: March 11, 2014, 09:57:50 PM »
Moreover, you need the line hooked up as it is the load sense for the transmission. It will shift hard enough to break parts with it disconnected. As the vacuum varies the shift gets harder or softer, it needs to get harder as car speed goes up to allow for more power applied to the transmission. That force going up and down is what allows clutches in trans to last longer.
Logged

Offline natedawg15

  • Pinto Member
  • **
  • Posts: 11
  • FeedBack: +0/-0
  • Another Pinto Driver

    • Total Badges: 1
    Badges: (View All)
    Topic Starter
Re: transmission lines
« Reply #6 on: March 14, 2014, 04:01:25 PM »
Ok I see the module but that is not it.  There are 2 lines that were toward the bell in the same area may even be the same hole.  Then there is a hole for something right under that, and then 1 toward the back of the trans.  I would like to know what these are before I hook everything up.  This is a ford c3 trans.  Thanks for any help you can give.
Logged

Offline dennisofaz

  • Pinto Member
  • **
  • Posts: 98
  • FeedBack: +25/-0

    • Total Badges: 5
    Badges: (View All)
    Topic Starter Tenth year Anniversary Poll Voter Windows User Fifth year Anniversary
Re: transmission lines
« Reply #7 on: March 14, 2014, 07:43:29 PM »
Hi Natedawg,


There are 3 connection points at the Bell.  The one facing backwards connects to the rear opening with a short tube.  the other 2 go to the hard lines connected to the radiators transmission cooler.  I do not think that it matters which side of the radiator trans cooler is in, or out.


Dennis
Logged

Offline natedawg15

  • Pinto Member
  • **
  • Posts: 11
  • FeedBack: +0/-0
  • Another Pinto Driver

    • Total Badges: 1
    Badges: (View All)
    Topic Starter
Re: transmission lines
« Reply #8 on: March 14, 2014, 07:57:15 PM »
  Thanks dennis that is what I was looking for.
Logged

Offline amc49

  • PCCA VIP
  • Pinto Master
  • ***
  • Posts: 1256
  • FeedBack: +242/-1
  • Another Pinto Driver

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Poll Voter Windows User 1000 Posts
Re: transmission lines
« Reply #9 on: March 15, 2014, 02:21:29 AM »
If using both radiator cooler and external you go to radiator first then external...... .........if either one by itself does not matter.
Logged
Pages: [1]   Go Up
« previous next »