Current Classifieds

1975 Pinto bumpers
Date: 01/20/2018 07:51 pm
WANTED: 1979 Bumper End Caps - Front and Rear
Date: 02/16/2019 10:46 am
71-71 speedo cable
Date: 07/31/2021 09:04 pm
Automatic Wagon
Date: 06/14/2019 11:22 pm
1971-74 Various Pinto Parts
Date: 01/18/2020 03:44 pm
74 Pinto Hub Caps & Trim Rings

Date: 02/28/2018 09:37 am
1970-1973 Gas Tank/Blue Dash
Date: 02/07/2019 11:57 pm
Lower Alternator bracket
Date: 08/26/2017 05:11 pm
4 speed pinto transmission

Date: 01/24/2021 07:54 pm
Wanted hood hinges
Date: 02/17/2020 05:30 pm
ENGINE COMPLETE 1971 PINTO
Date: 12/28/2017 03:55 pm
Hoard of Pinto parts
Date: 12/17/2016 04:14 pm

« previous next »
Pages: [1]   Go Down

Author Topic: Timing issues  (Read 2360 times)

0 Members and 1 Guest are viewing this topic.

Offline Farmboy

  • Pinto Sr. Member
  • ****
  • Posts: 431
  • FeedBack: +0/-0
  • Gender: Male

    • Total Badges: 6
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User Tenth year Anniversary Fifth year Anniversary
Timing issues
« on: June 13, 2012, 07:18:20 PM »
  Ok, been setting the timing right on the marks, point gap is perfect, new point and condenser. Car is warmer up and ready to drive, pull out drive 4 to 6 miles, it stall's for a millasecount and it goes out of time. I'm pulling my hair out trying to figgure out what I'm doing wrong. Its a rebuilt 2.0 with a 4 speed. Don't know it I should go and buy another Dist. and try that. The aux. shaft looks good from what I can see looking thru the dist. hole.
  any ideas from you folks
Logged
  I do what the voices in my Pinto tell me to do




74 Pinto Wagon
71 Runabout (parts car)

Offline r4pinto

  • Pinto PooBAH
  • ******
  • Posts: 3854
  • FeedBack: +108/-0
  • Gender: Male
  • All hail Ford Pinto!!!!

    • Total Badges: 9
    Badges: (View All)
    Topic Starter Signature Poll Voter Linux User Mobile User Windows User 1000 Posts Tenth year Anniversary Fifth year Anniversary
Re: Timing issues
« Reply #1 on: June 13, 2012, 07:50:08 PM »
Out of curiosity have you checked the cam timing to see if that may be off?
 
Logged
Matt Manter
1977 Pinto sedan- Named Harold II after the first Pinto(Harold) owned by my mom. R.I.P mom- 1980 parts provider & money machine for anything that won't fit the 80
1980 Pinto Runabout- work in progress

Offline Farmboy

  • Pinto Sr. Member
  • ****
  • Posts: 431
  • FeedBack: +0/-0
  • Gender: Male

    • Total Badges: 6
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User Tenth year Anniversary Fifth year Anniversary
Re: Timing issues
« Reply #2 on: June 13, 2012, 09:19:48 PM »
Everything lines up like its suppost too, kinda sick of getting it running good only to last a few miles
 
Logged
  I do what the voices in my Pinto tell me to do




74 Pinto Wagon
71 Runabout (parts car)

Offline r4pinto

  • Pinto PooBAH
  • ******
  • Posts: 3854
  • FeedBack: +108/-0
  • Gender: Male
  • All hail Ford Pinto!!!!

    • Total Badges: 9
    Badges: (View All)
    Topic Starter Signature Poll Voter Linux User Mobile User Windows User 1000 Posts Tenth year Anniversary Fifth year Anniversary
Re: Timing issues
« Reply #3 on: June 13, 2012, 09:29:22 PM »
Quote from: Farmboy on June 13, 2012, 09:19:48 PM
Everything lines up like its suppost too, kinda sick of getting it running good only to last a few miles

The way it sounds if everything is lining up it very well could be a bad distributor. sounds like it's got some wear in the distributor shaft.
Logged
Matt Manter
1977 Pinto sedan- Named Harold II after the first Pinto(Harold) owned by my mom. R.I.P mom- 1980 parts provider & money machine for anything that won't fit the 80
1980 Pinto Runabout- work in progress

Offline Pinto5.0

  • Pinto Master
  • *****
  • Posts: 1974
  • FeedBack: +77/-0
  • Gender: Male
  • 80 hatch, 76 Wagon, 72 & 73 Sedans, 71 half hatch

    • Total Badges: 7
    Badges: (View All)
    Topic Starter Signature Poll Voter Mobile User Fifth year Anniversary Windows User 1000 Posts
Re: Timing issues
« Reply #4 on: June 13, 2012, 09:33:04 PM »
Do you just need to move the distributor a little or do you need to pull it & drop it in a tooth over each time?
 
Check the gear on the distributor & see if it's pinned to the shaft or moving.
Logged
'73 Sedan (I'll get to it)
'76 Wagon driver
'80 hatch(Restoring to be my son's 1st car)~Callisto
'71 half hatch (bucket list Pinto)~Ghost
'72 sedan 5.0/T5~Lemon Squeeze

Offline Farmboy

  • Pinto Sr. Member
  • ****
  • Posts: 431
  • FeedBack: +0/-0
  • Gender: Male

    • Total Badges: 6
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User Tenth year Anniversary Fifth year Anniversary
Re: Timing issues
« Reply #5 on: June 13, 2012, 10:57:07 PM »
Quote from: Pinto5.0 on June 13, 2012, 09:33:04 PM
Do you just need to move the distributor a little or do you need to pull it & drop it in a tooth over each time?
 
Check the gear on the distributor & see if it's pinned to the shaft or moving.
Just need to move the dist. a little to get it back running decent, if you hold the top of the dist shaft there is some play when twisting the geared end at the bottom. Is it suppost to be solid top to bottom?
Logged
  I do what the voices in my Pinto tell me to do




74 Pinto Wagon
71 Runabout (parts car)

Offline r4pinto

  • Pinto PooBAH
  • ******
  • Posts: 3854
  • FeedBack: +108/-0
  • Gender: Male
  • All hail Ford Pinto!!!!

    • Total Badges: 9
    Badges: (View All)
    Topic Starter Signature Poll Voter Linux User Mobile User Windows User 1000 Posts Tenth year Anniversary Fifth year Anniversary
Re: Timing issues
« Reply #6 on: June 13, 2012, 11:24:47 PM »
I believe so. I don't think you're supposed to be able to move the bottom gear if holding the top. Sounds like there could be the problem.
Logged
Matt Manter
1977 Pinto sedan- Named Harold II after the first Pinto(Harold) owned by my mom. R.I.P mom- 1980 parts provider & money machine for anything that won't fit the 80
1980 Pinto Runabout- work in progress

Offline oldkayaker

  • Pinto Master
  • *****
  • Posts: 758
  • FeedBack: +114/-0
  • Gender: Male

    • Total Badges: 5
    Badges: (View All)
    Topic Starter Signature Windows User Tenth year Anniversary Fifth year Anniversary
Re: Timing issues
« Reply #7 on: June 14, 2012, 07:04:33 AM »
Just to clarify, there is a small amount of play when twisting the rotor and holding the gear.  I believe this is due to the centrifical advance mechanism in there.

 
  • Can you see light through the gear roll pin?  If not, the roll pin may be sheared.  Is the timing jumping in the same direction?
  • Since it is warm up related, maybe the vacuum circuit is flaky.  Try disconnecting the vacuum advance and see if the the timing jump reoccurs.  Is the timing jumping back and forth in direction?
  • Disassemble the top of the distributor to inspect the centrifical advance stuff.
  • A remote possibility is that the auxiliary shaft to pulley key is sheared.  This would also cause the timing to jump in the same direction.
Since you said the belt has not skipped a tooth and the gears have their teeth, I can not suggest anything else.  Good luck with the search.
Logged
Jerry J - Jupiter, Florida
Pages: [1]   Go Up
« previous next »