Current Classifieds

Automatic transmission
Date: 02/13/2021 02:52 pm
79 pinto headlight,tailight,side marker light assemblies

Date: 07/17/2018 09:22 pm
1978 ford pinto door striker (passenger side)
Date: 09/01/2017 11:58 am
Plug Or Cover For Hatch Hinge Bolt For 1979
Date: 05/28/2017 03:20 pm
1979 Pinto Rear Bumper
Date: 03/26/2021 03:26 pm
Mirror
Date: 04/15/2020 01:42 pm
Want side to side luggage rack rails for '75 Pinto wagon
Date: 08/30/2018 12:59 am
1971 2 lt Cam
Date: 10/10/2020 06:27 pm
'71,'72,or'73 small Ford v8 Pinto
Date: 01/23/2017 07:41 am
1973 Pinto Wagon

Date: 05/06/2022 05:13 pm
rear hatch back louvers

Date: 04/18/2017 12:44 pm
1979/80 Pinto needs to be saved
Date: 09/10/2018 10:41 pm

Author Topic: Timing belt tensioner spring  (Read 2391 times)

0 Members and 1 Guest are viewing this topic.

Offline rramjet

  • Pinto Full Member
  • ***
  • Posts: 120
  • FeedBack: +3/-0
  • Another Pinto Driver

  • Total Badges: 1
    Badges: (View All)
    Topic Starter
Timing belt tensioner spring
« on: September 30, 2013, 08:11:25 PM »
My timing belt tensioner has a spring on it however I think the tensioner was just locked down with the bolt. I've done a little web searching on the subject and it seems many don't even use the spring they judge belt tension by being able to twist the long section of the belt about 90 degrees.

Anyone else running the spring and if so is it intended to establish the tension then the tensioner mount bolt is just tightened at that point?

Guess I could just go read my manual, but this is so much more fun.

Offline 74 PintoWagon

  • Pinto Sr. Master
  • ******
  • Posts: 3105
  • FeedBack: +540/-0
  • Gender: Male
  • Another Pinto Driver

  • Total Badges: 5
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User 1000 Posts
Re: Timing belt tensioner spring
« Reply #1 on: September 30, 2013, 10:01:14 PM »
According to Ford manual the spring puts on the required tension then tighten the bolt, kinda takes out the guess work..
Art
65 Falcon 2DR 200 IL6 with C4.

Offline rramjet

  • Pinto Full Member
  • ***
  • Posts: 120
  • FeedBack: +3/-0
  • Another Pinto Driver

  • Total Badges: 1
    Badges: (View All)
    Topic Starter
Re: Timing belt tensioner spring
« Reply #2 on: September 30, 2013, 11:05:57 PM »
Thanks.

That's pretty much what my Chilton book says too. Guess I'll do both. Put the spring back on and see how much twist I get on the belt, in case the spring has lost some of it's strength after 95K miles.

Offline 74 PintoWagon

  • Pinto Sr. Master
  • ******
  • Posts: 3105
  • FeedBack: +540/-0
  • Gender: Male
  • Another Pinto Driver

  • Total Badges: 5
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User 1000 Posts
Re: Timing belt tensioner spring
« Reply #3 on: October 01, 2013, 07:46:19 AM »
Kinda wondered that myself, maybe I missed it but I couldn't find any specs for that spring?, maybe they're supposed to be replaced after a certain time as routine maintenance schedule?..
Art
65 Falcon 2DR 200 IL6 with C4.

Offline amc49

  • PCCA VIP
  • Pinto Master
  • ***
  • Posts: 1256
  • FeedBack: +242/-1
  • Another Pinto Driver

  • Total Badges: 4
    Badges: (View All)
    Topic Starter Poll Voter Windows User 1000 Posts
Re: Timing belt tensioner spring
« Reply #4 on: October 01, 2013, 08:05:49 AM »
I wouldn't worry about it, the spring does nothing once bolt is tightened down. If tension falls off no real biggie anyway. The later stuff nowadays (zetec) uses so little tension most people have a tendency to overtighten them. It often fails the belt since belt has no real guides, tightening it then makes the belt steer to pulley edge where it frays and DNF.

The spring is actually only correct with a NEW belt, once belt is run in then the spring is actually too much. Meaning you should not back off the tensioner unless changing the belt. Backing off to retension later in belt life shortens it, the tension is SUPPOSED to drop off as engine runs, the lower tension later allows belt to last longer.


Offline 74 PintoWagon

  • Pinto Sr. Master
  • ******
  • Posts: 3105
  • FeedBack: +540/-0
  • Gender: Male
  • Another Pinto Driver

  • Total Badges: 5
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User 1000 Posts
Re: Timing belt tensioner spring
« Reply #5 on: October 01, 2013, 08:22:35 AM »
The 2.3 has one belt guide on the crank.
Art
65 Falcon 2DR 200 IL6 with C4.

Offline rramjet

  • Pinto Full Member
  • ***
  • Posts: 120
  • FeedBack: +3/-0
  • Another Pinto Driver

  • Total Badges: 1
    Badges: (View All)
    Topic Starter
Re: Timing belt tensioner spring
« Reply #6 on: October 01, 2013, 02:43:36 PM »
Good info and makes sense.

I'm putting a new belt and tensioner on but using original spring. Belt was ok just figured since the head was off and I had no way of knowing how lold the belt and tensioner were but guessing original it was best to do both.

Offline 74 PintoWagon

  • Pinto Sr. Master
  • ******
  • Posts: 3105
  • FeedBack: +540/-0
  • Gender: Male
  • Another Pinto Driver

  • Total Badges: 5
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User 1000 Posts
Re: Timing belt tensioner spring
« Reply #7 on: October 01, 2013, 03:04:18 PM »
When I got the wagon I changed it out, just for peace of mind.
Art
65 Falcon 2DR 200 IL6 with C4.

Offline amc49

  • PCCA VIP
  • Pinto Master
  • ***
  • Posts: 1256
  • FeedBack: +242/-1
  • Another Pinto Driver

  • Total Badges: 4
    Badges: (View All)
    Topic Starter Poll Voter Windows User 1000 Posts
Re: Timing belt tensioner spring
« Reply #8 on: October 03, 2013, 06:11:53 AM »
My bad, I meant later stuff like now. I have three zetec powered cars and people have pure fits trying to tension those things since they use like 1/5 the tension these Pinto motors do.

2.3 SOHC actually guided on both sides, one at the crank (front limit) and other at top behind cam sprocket, it has a back limiting plate.

Offline 74 PintoWagon

  • Pinto Sr. Master
  • ******
  • Posts: 3105
  • FeedBack: +540/-0
  • Gender: Male
  • Another Pinto Driver

  • Total Badges: 5
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User 1000 Posts
Re: Timing belt tensioner spring
« Reply #9 on: October 03, 2013, 08:44:53 AM »
Yep, forgot about the top one. Yeah, new stuff is all different now..
Art
65 Falcon 2DR 200 IL6 with C4.

Offline rramjet

  • Pinto Full Member
  • ***
  • Posts: 120
  • FeedBack: +3/-0
  • Another Pinto Driver

  • Total Badges: 1
    Badges: (View All)
    Topic Starter
Re: Timing belt tensioner spring
« Reply #10 on: October 03, 2013, 11:50:50 AM »
My bad, I meant later stuff like now. I have three zetec powered cars and people have pure fits trying to tension those things since they use like 1/5 the tension these Pinto motors do.

2.3 SOHC actually guided on both sides, one at the crank (front limit) and other at top behind cam sprocket, it has a back limiting plate.

My 2.0 also has a guide behind the crank pulley and behind the cam sprocket.