Current Classifieds

1.6 New Ford cylinder head with side draft carbs

Date: 06/12/2018 08:18 pm
Pinto porthole exterior trim wanted
Date: 03/30/2021 12:29 pm
vintage Pinto script sunshades

Date: 03/05/2017 03:27 pm
looking for 1978 pinto head rebuild kit
Date: 05/24/2020 08:19 am
79 pinto driveshaft
Date: 08/18/2018 02:03 pm
Weather Strip, Muffler, Splash Shields

Date: 02/21/2022 11:11 pm
Looking for 1.6 exhaust manifold heat shield, front license plate bracket
Date: 11/04/2018 02:34 am
Clutch Cable Needed
Date: 04/03/2017 11:03 pm
LOOKING for INTERIOR PARTS, MIRRORS & A HOOD LATCH
Date: 04/06/2017 12:13 am
1975 Ford Pinto

Date: 01/13/2020 11:02 am
1971 2.0 valve cover
Date: 01/25/2019 07:09 pm
74 4 spd and rear axle
Date: 09/26/2018 03:51 pm

« previous next »
Pages: [1]   Go Down

Author Topic: Timing  (Read 797 times)

0 Members and 1 Guest are viewing this topic.

Offline thunderchickentoo

  • Pinto Driver
  • *
  • Posts: 3
  • FeedBack: +0/-0
  • Combat Medic

    • Total Badges: 3
    Badges: (View All)
    Signature Topic Starter Mobile User
Timing
« on: January 08, 2020, 08:50:33 PM »
1980 2.3. Where does the mark on the balance shaft sprocket line up. Don't see a triangle or diamond or any mark on the engine or.  Also no mark on the distributor plate to mark number 1
Logged
Jonathan

Offline nnn0wqk

  • Pinto Member
  • **
  • Posts: 99
  • FeedBack: +24/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 5
    Badges: (View All)
    Topic Starter Poll Voter Windows User Tenth year Anniversary Fifth year Anniversary
Re: Timing
« Reply #1 on: January 09, 2020, 12:16:26 AM »
As I recall and it has been lots of years since I replaced my timing belt, I do not recall a timing mark on the aux shaft. Crank lines up with timing mark on cover, cam you can see through the plug in cover and it is at about 5 o'clock. Aline dist rotor with number one on the cap. Which looks to be straight out from the engine. Dist rotates clockwise according to the picture I am looking at.
Logged

Offline 65ShelbyClone

  • Pinto Master
  • *****
  • Posts: 787
  • FeedBack: +139/-0
  • Soylent Green

    • Total Badges: 7
    Badges: (View All)
    Fifth year Anniversary Topic Starter Signature Poll Voter Mobile User Linux User Windows User
Re: Timing
« Reply #2 on: February 08, 2020, 12:03:26 PM »
It's not a balance shaft, it's an auxiliary shaft that drives the oil pump, fuel pump, and distributor. Orientation doesn't matter as long as you can rotate the distributor enough to properly set the timing.
Likewise, the #1 distributor terminal can be any of the four as long as the rotor is pointing at it when the #1 cylinder is at TDC.
Logged
'72 Runabout - 2.3T, T5, MegaSquirt-II, 8", 5-lugs, big brakes.
'68 Mustang - Built roller 302, Toploader, 9", etc.

Offline Wittsend

  • Pinto Master
  • *****
  • Posts: 2498
  • FeedBack: +241/-0

    • Total Badges: 8
    Badges: (View All)
    Tenth year Anniversary Mobile User Topic Starter Poll Voter 1000 Posts Linux User Windows User Fifth year Anniversary
Re: Timing
« Reply #3 on: February 08, 2020, 02:13:12 PM »
I'll add that whenever I change a timing belt I put different color paint marks on the belts and pulleys. I then transfer those marks to the new belt. That way there is  misunderstandi ng vague markers that might have scuffed off, bent, broken etc.. I also take before and after pictures. It adds 10 minutes to the task and eliminates 99.9% WHAT!!! - if later something isn't working right. I'm getting too old to remember..., if I remembered.
Logged
Pages: [1]   Go Up
« previous next »