Current Classifieds

1975 Ford Pinto

Date: 01/13/2020 11:02 am
Wanted Postal Pinto
Date: 09/26/2019 05:31 pm
New front rotors and everything for '74-'80
Date: 08/02/2019 04:18 pm
1971 yellow Pinto hatchback with limited edition chrome strips on rear door, 1600 cc engine

Date: 02/26/2017 03:22 pm
Mint Original Black Rear Seat $275.00

Date: 07/30/2020 11:45 am
hood for a 79-80
Date: 11/30/2018 10:55 pm
v8 springs
Date: 05/07/2017 04:46 pm
SOME PARTS FOR SALE
Date: 01/11/2017 10:45 am
1980 Ford Pinto Squire Wagon * All original 1 Owner *

Date: 09/15/2019 12:28 pm
1972 Pinto SCCA BS race car

Date: 10/23/2018 04:01 pm
1976 (non hatchback) pinto (90% complete project)

Date: 07/10/2016 10:17 am
Beautiful 1980 Pinto

Date: 04/13/2020 11:53 am

Author Topic: T5 tranny mount pics Anyone got any so I can see what I need???  (Read 1767 times)

0 Members and 1 Guest are viewing this topic.

Offline Ruger Nut

  • Pinto Member
  • **
  • Posts: 60
  • FeedBack: +0/-0
  • Gender: Male

  • Total Badges: 3
    Badges: (View All)
    Topic Starter Poll Voter Fifth year Anniversary
I'm trying to get the tranny mount correct.  Does anyone have pics of theirs??   Also how did you connect the Pinto clutch cable to the Bell crank T5 z arm??   Thanks

Offline CHEAPRACER

  • Pinto Sr. Member
  • ****
  • Posts: 561
  • FeedBack: +10/-0
  • Gender: Male
  • Registered Ride #27

  • Total Badges: 5
    Badges: (View All)
    Topic Starter Signature Poll Voter Tenth year Anniversary Fifth year Anniversary
Re: T5 tranny mount pics Anyone got any so I can see what I need???
« Reply #1 on: March 27, 2012, 12:38:18 AM »
Everything has already been done & posted in the faq section.

http://www.fordpinto.com/pinto-faq/5spd-t-5-installswap-information/
Cheapracer is my personality but you can call me Jim '74 Pinto, stock 2.3 turbo, LA3, T-5, 8" 3:55 posi, Former (hot) cars: '71 383 Cuda, 67 440 Cuda, '73 340 Dart, '72 396 Vega, '72 327 El Camino, '84 SVO, '88 LX 5.0

Offline Wittsend

  • Pinto Master
  • *****
  • Posts: 2370
  • FeedBack: +241/-0

  • Total Badges: 8
    Badges: (View All)
    Tenth year Anniversary Mobile User Topic Starter Poll Voter 1000 Posts Linux User Windows User Fifth year Anniversary
Re: T5 tranny mount pics Anyone got any so I can see what I need???
« Reply #2 on: March 27, 2012, 08:52:41 PM »
Here are a few pictures from my swap (T-5 in a 73 wagon).

1. The slotted and reversed trans crossmember. It was still tight at the rear and I had to flatten the edge of the washers to get the fit right.  Note that I slotted all the holes, including those that bolt to the unibody. I wanted as much flexibility as I could get.

2. I did not use the factory hole in the bellhousing for the clutch cable. I created a bracket that bolted to that hole. It helped get the cable above the crossmember.

3. A close up of the bracket. There is a slight angle to it that helps in regard to the cable/crossmember clearance. I did have to bend out the pivot arm on the bellhousing slightly.  Also, I welded on a little tab that acts as an anti-rotate if the bracket bolt ever loosened.

4. I'm 6 feet tall and like my shifter back far. I added this extension plate onto the shifter. I also cut and welded the shifter height to my liking. Not seen is the Murkur console I used. Also not seen is the tunnel cut you need to make for the T-5. The opening is too far to the rear and you need to cut about 3" forward.

Tom