Current Classifieds

Tubing bender 1/2 to 2 1/2 (3) inch roll cage / mufflers and more

Date: 03/13/2021 12:57 pm
1970-1973 Gas Tank/Blue Dash
Date: 02/07/2019 11:57 pm
1980 Pinto taillights
Date: 12/26/2017 03:48 pm
Wanted 71-73 Pinto grill
Date: 03/09/2019 10:45 pm
NEED 77/78 MUSTANG II Left Motor Mount
Date: 04/15/2017 05:14 pm
V8 rear end
Date: 04/12/2018 10:57 am
Need 2.3 timing cover
Date: 08/10/2018 11:41 am
1978 pinto brake booster needed.
Date: 04/07/2021 06:12 pm
vintage Pinto script sunshades

Date: 03/05/2017 03:27 pm
Drivers side door panel Orange
Date: 05/22/2018 02:27 pm
turbo 4 cyl and aod trans
Date: 12/14/2019 04:55 pm
I have a 1977 Cobra body lots of parts here
Date: 04/12/2017 06:57 pm

Author Topic: Sway bar help..  (Read 1726 times)

0 Members and 1 Guest are viewing this topic.

Offline Rob3865

  • Pinto Full Member
  • ***
  • Posts: 202
  • FeedBack: +19/-2
  • Gender: Male
  • Another Pinto Driver

  • Total Badges: 5
    Badges: (View All)
    Mobile User Topic Starter Signature Poll Voter Windows User
Sway bar help..
« on: February 19, 2017, 01:44:00 PM »
Will the rear sway bar from a Mustang II fit on a 1976 Bobcat?  I have an 8" Mustang II rear axle under it now with the Mustang II shock plates. I think it will fit, but I am not certain. Any help is appreciated.

Thanks.

Offline dick1172762

  • Vintage Pinto Racer
  • PCCA Management Board
  • Pinto Sr. Master
  • ******
  • Posts: 2623
  • FeedBack: +362/-0
  • Gender: Male
  • I'm a llama!

  • Total Badges: 7
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User 1000 Posts Tenth year Anniversary Fifth year Anniversary
Re: Sway bar help..
« Reply #1 on: February 19, 2017, 02:30:01 PM »
It will fit just fine. The Mustang II and the Pinto's are the same at the rear end except for the shock mount (which also is the sway bar mount). If you don't have the rest of the sway bar links / bushings / etc they are easy to make. The parts don't need to be a carbon copy to work. As you know the shocks are different between the two cars in the way they mount at the spring perch. If you attach the sway bar links to the frame as a Mustang II does you'll have no problem's but if you attach the links to the floor boards like an ADCO bar does, you must reinforce the floor boards or they will crack with use. Frame mount is best with a Mustang II bar. Hope this helps. Is this a racer of any kind?
Its better to be a has-been, than a never was.

Offline Rob3865

  • Pinto Full Member
  • ***
  • Posts: 202
  • FeedBack: +19/-2
  • Gender: Male
  • Another Pinto Driver

  • Total Badges: 5
    Badges: (View All)
    Mobile User Topic Starter Signature Poll Voter Windows User
Re: Sway bar help..
« Reply #2 on: February 19, 2017, 09:27:04 PM »
No sir, not a race car. I am over all of that by about 30 years. It is going to be a V8 car though. Mild GT40P roller engine, T5 transmission, 3.40 gear set. Just something fun for an old man to knock around on the street.

Offline dick1172762

  • Vintage Pinto Racer
  • PCCA Management Board
  • Pinto Sr. Master
  • ******
  • Posts: 2623
  • FeedBack: +362/-0
  • Gender: Male
  • I'm a llama!

  • Total Badges: 7
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User 1000 Posts Tenth year Anniversary Fifth year Anniversary
Re: Sway bar help..
« Reply #3 on: February 20, 2017, 08:05:07 AM »
Sounds great. Keep us up to date on the build.
Its better to be a has-been, than a never was.

Offline Rob3865

  • Pinto Full Member
  • ***
  • Posts: 202
  • FeedBack: +19/-2
  • Gender: Male
  • Another Pinto Driver

  • Total Badges: 5
    Badges: (View All)
    Mobile User Topic Starter Signature Poll Voter Windows User
Re: Sway bar help..
« Reply #4 on: February 20, 2017, 10:31:27 PM »
I think I have just decided to just pull the stops out and get the Addco bars front and rear. Finding used ones is tough and and when found people think their 40 year old crap is gold plated.

Offline dick1172762

  • Vintage Pinto Racer
  • PCCA Management Board
  • Pinto Sr. Master
  • ******
  • Posts: 2623
  • FeedBack: +362/-0
  • Gender: Male
  • I'm a llama!

  • Total Badges: 7
    Badges: (View All)
    Topic Starter Signature Poll Voter Windows User 1000 Posts Tenth year Anniversary Fifth year Anniversary
Re: Sway bar help..
« Reply #5 on: February 21, 2017, 08:34:51 AM »
I don't think a ADCO bar will clear the oil pan on a V-8 Pinto. The Mustang II one inch front bar is made to clear the pan, but hard to find. ADCO should know. I would use both front and back bars from a V-8 Mustang II because a V-8 Pinto will never handle. Most have no bars at all, as there being used mostly for straight line driving. Do a search on here to see what others have done.
Its better to be a has-been, than a never was.

Offline Rob3865

  • Pinto Full Member
  • ***
  • Posts: 202
  • FeedBack: +19/-2
  • Gender: Male
  • Another Pinto Driver

  • Total Badges: 5
    Badges: (View All)
    Mobile User Topic Starter Signature Poll Voter Windows User
Re: Sway bar help..
« Reply #6 on: February 22, 2017, 10:25:57 PM »
I found a rear bar from a Rustang II. Thanks for the advice. Now to find a front.