Current Classifieds

72 Runabout for Sale- Washington

Date: 02/28/2024 02:07 pm
Tubing bender 1/2 to 2 1/2 (3) inch roll cage / mufflers and more

Date: 03/13/2021 12:57 pm
4 speed pinto transmission

Date: 01/24/2021 07:54 pm
Windshield
Date: 01/15/2022 09:31 pm
Floor pans for my 1975 Pinto Sedan
Date: 12/09/2016 08:34 am
1979 PINTO PARTS--FREE
Date: 09/13/2022 02:05 pm
1971 Pinto 5.0L

Date: 12/02/2017 12:23 am
Looking for Passenger side Inner Fender Apron
Date: 10/28/2018 08:45 am
1977 Pinto Cruising Wagon FOR SALE

Date: 08/20/2017 01:34 pm
Wiring diagram Ignition switch 72 2.0 4 speed pinto wagon
Date: 12/31/2017 11:14 pm
SVO SWAP
Date: 03/15/2018 03:12 am
Needed- Good 71-73 Rear End or parts- close to AL
Date: 09/15/2019 12:38 pm

« previous next »
Pages: [1]   Go Down

Author Topic: strut rod bushings  (Read 1793 times)

0 Members and 2 Guests are viewing this topic.

Offline ToniJ1960

  • Pinto Sr. Member
  • ****
  • Posts: 544
  • FeedBack: +13/-0
  • Gender: Female
  • Another Pinto Driver

    • Total Badges: 5
    Badges: (View All)
    Tenth year Anniversary Topic Starter Poll Voter Fifth year Anniversary Windows User
strut rod bushings
« on: March 09, 2012, 04:14:51 PM »
 Well my 78 wagon with power steering needs an alignment Since I had the inner tie rod end replaced on the drivers side its pulling to the right.

 Should I wait until I get the strut rod bushings changed before I get the alignment done? Will it need to be done again I guess is what Im wondering.

 And is it pulling t o the right because he didnt get the outer tie rod end on the same as the old one? Would it need to go on another turn or two or the opposite way?
Logged

Offline dave1987

  • Pinto Sr. Master
  • ******
  • Posts: 3431
  • FeedBack: +25/-0
  • Gender: Male

    • Total Badges: 11
    Badges: (View All)
    Topic Starter Signature Tenth year Anniversary Poll Voter Mobile User Apple User Linux User Windows User 1000 Posts Fifth year Anniversary Photographer
Re: strut rod bushings
« Reply #1 on: March 10, 2012, 12:23:11 AM »
I would wait. Any time non routine maintenance is done I do qn qlignment since the geometry of the suspension is changed.
Logged
1978 Ford Pinto Sedan - Family owned since new

Remembering Jeff Fitcher with every drive in my 78 Sedan.

I am a Pinto Surgeon. Fixing problems and giving Pintos a chance to live again is more than a hobby, it's a passion!

Offline ToniJ1960

  • Pinto Sr. Member
  • ****
  • Posts: 544
  • FeedBack: +13/-0
  • Gender: Female
  • Another Pinto Driver

    • Total Badges: 5
    Badges: (View All)
    Tenth year Anniversary Topic Starter Poll Voter Fifth year Anniversary Windows User
Re: strut rod bushings
« Reply #2 on: March 10, 2012, 03:22:19 AM »
 Thats the big question is the geometry changed from what I read about the mustang ii they say that since the strut rods are non adjustable anyway it doesnt change it to replace them. I would think its the same on the Pinto?
Logged

Offline Srt

  • Original Pangra Master Builder
  • PCCA VIP
  • Pinto Master
  • ***
  • Posts: 1339
  • FeedBack: +100/-0
  • Gender: Male

    • Total Badges: 10
    Badges: (View All)
    Topic Starter Signature Tenth year Anniversary Poll Voter Linux User Mobile User Windows User 1000 Posts Fifth year Anniversary Photographer
Re: strut rod bushings
« Reply #3 on: March 10, 2012, 03:25:42 AM »
Quote from: tonij1960 on March 10, 2012, 03:22:19 AM
Thats the big question is the geometry changed from what I read about the mustang ii they say that since the strut rods are non adjustable anyway it doesnt change it to replace them. I would think its the same on the Pinto?

if the strut rod bushings are worn the alignment can change easily due to fore & aft movement of the lower arm.  changing them out before the alignment is a good idea.
Logged
the only substitute for cubic inches is BOOST!!!
Pages: [1]   Go Up
« previous next »