Current Classifieds

1977 Pinto for parts

Date: 10/10/2018 06:25 pm
1971 Pinto

Date: 03/04/2017 11:28 pm
76 station wagon parts needed.
Date: 03/14/2020 01:52 pm
1972 Runabout 351 Cleveland V8

Date: 11/05/2016 09:03 pm
WANTED Hood Prop Rod
Date: 01/17/2017 02:47 pm
1974 Wiring diagram free
Date: 10/27/2019 06:56 pm
Needed- Good 71-73 Rear End or parts- close to AL
Date: 09/15/2019 12:38 pm
72 PINTO WAGON

Date: 09/23/2018 06:16 pm
WTB Cruising Wagon
Date: 12/07/2016 05:35 pm
Weather Strip, Muffler, Splash Shields

Date: 02/21/2022 11:11 pm
Needed, 2.0 or 2.3 motors
Date: 09/30/2018 07:47 pm
77 Cruising Wagon Front Seats
Date: 04/12/2017 12:37 pm

Author Topic: 2.0 Freeze plugs question and intro  (Read 2489 times)

0 Members and 1 Guest are viewing this topic.

Offline 1oldtimer

  • Pinto Member
  • **
  • Posts: 42
  • FeedBack: +61/-0
  • Gender: Male
  • Another Pinto Motor

  • Total Badges: 5
    Badges: (View All)
    Fifth year Anniversary Topic Starter Signature Mobile User Windows User
2.0 Freeze plugs question and intro
« on: July 08, 2012, 11:30:55 PM »
Hello, this is my first post. My name is Dan and I have a '72 2.0 Pinto motor in a '28 Ford Tudor. I'm planning to keep the motor and hop it up a little bit, but first I need to do some repairs. I'm replacing the freeze plugs and I'm only finding 3 (2 on the exhaust side and 1 on the back of the head) all the same size. Is there any other plugs inside the bellhousing area?, I would rather not pull the motor out if there's none in there. Also where is the block drain plug for coolant or is there one?, the P/O used water and things are pretty rusty inside and I need the lowest hole to flush out the block.

Thanks,
Dan (1oldtimer)
'72 2.0 in a '28 Ford.

Offline oldkayaker

  • Pinto Master
  • *****
  • Posts: 758
  • FeedBack: +114/-0
  • Gender: Male

  • Total Badges: 5
    Badges: (View All)
    Topic Starter Signature Windows User Tenth year Anniversary Fifth year Anniversary
Re: 2.0 Freeze plugs question and intro
« Reply #1 on: July 09, 2012, 08:03:48 AM »
Welcome aboard.  There is a large freeze plug on the back of the block.  The lowest coolant drain point on the block appears to be the temperature sender hole on the passenger side near the back.  I did not find a dedicated drain port.
 
You might want to check with a radiator shop to see if there is a way to clean out the rust before freeze plug replacement.  Just concerned the cleaner may damage the new freeze plugs.  I have used pool acid to clean the water jacket, which will remove the galvanizing from the freeze plugs (this was on a stripped bare block).  Have fun.
Jerry J - Jupiter, Florida

Offline 1oldtimer

  • Pinto Member
  • **
  • Posts: 42
  • FeedBack: +61/-0
  • Gender: Male
  • Another Pinto Motor

  • Total Badges: 5
    Badges: (View All)
    Fifth year Anniversary Topic Starter Signature Mobile User Windows User
Re: 2.0 Freeze plugs question and intro
« Reply #2 on: July 10, 2012, 12:04:54 AM »
Thanks Jerry, It looks like the motor has to come out. It's not really bad inside, I was going to use the garden hose to get all the brown water out and hope fresh coolant will keep it from getting worse. Either that or I'll run some rusty coolant cleaner I bought, you run it with water for 6 hours and drain. I would have done it before I took it apart but the old radiator leaked so bad it was all over the motor and firewall.
'72 2.0 in a '28 Ford.