Current Classifieds

free transmissions
Date: 11/28/2019 10:21 am
1978 PINTO PONY FOR SALE 17,000 ORIGINAL MILES !!!!!!!
Date: 10/10/2019 09:42 pm
2.0 Mickey Thompson SUPER RARE Rocker cover and belt guard
Date: 08/22/2017 09:21 pm
Tubing bender 1/2 to 2 1/2 (3) inch roll cage / mufflers and more

Date: 03/13/2021 12:57 pm
Instrument Panel with Tach wanted
Date: 05/15/2022 11:36 am
Need 2.3 timing cover
Date: 08/10/2018 11:41 am
parting out 1975 & 80 pintos
Date: 08/24/2018 02:50 pm
72 pinto and 88 turbo coupe

Date: 06/09/2016 04:13 am
1971 2 lt Cam
Date: 10/10/2020 06:27 pm
78 pinto wagon

Date: 03/03/2020 01:07 pm
2.3/C-4 torque converter needed
Date: 02/08/2018 02:26 pm
Bumper, grill and fender wanted
Date: 12/24/2016 04:13 pm

Author Topic: Starting issues again.......  (Read 534 times)

0 Members and 1 Guest are viewing this topic.

Offline Nudemaple

  • Pinto Member
  • **
  • Posts: 16
  • FeedBack: +0/-0
  • Gender: Male
  • Another Pinto Driver

  • Total Badges: 1
    Badges: (View All)
    Topic Starter
Starting issues again.......
« on: May 08, 2022, 09:52:42 PM »
Last Thursday, 5-5-22, I went to start it like I usually do and it cranked fine but didn't turn over. Tried again and gave it a bit more gas and still did not turn over. One more time and I smelled gas. I took off the air filter and noticed that fuel had sprayed on the air filter. I figured I flooded it though I didn't step that far down on the gas during startup. I let it settle overnight.

Friday, 5-6-22, same thing happened but this time I removed everything and placed a towel over the carb. I started it and it was damp with fuel. I let it settle overnight.

Saturday, 5-7-22, same thing....no improvement.

Sunday morning. 5-8-22
As suggested by a member in my previous post, I tapped the carb housing gently with a hammer and wood block in case the float was stuck and tried to start with a new extra coil installed. This resulted in no spraying of fuel as previously but still did not turn over fully. Again I tried starting with gas pedal all the way down and it did turn over but after violent shaking for about 30 seconds it shut down completely.
I noticed smoke/vapor circulating within the carb chamber mostly on the passenger side. It was not a burning smell. Actually it did not smell at all..not even like fuel. I let it settle overnight.

Monday afternoon 5-9-22
I removed all the spark plugs as was suggested in my previous post. Only one was wet and smells like fuel. The other 3 were dry. I dried all of them with a heat gun. Once cool, I installed them again. Pressed the gas pedal all the way down and cranked and it started BEAUTIFULLY... .I let it run for 3 minutes and it idled at around 2000rpm...when I pressed the gas pedal again to allow it to idle down to 800rpm.... the engine idled extremely low with consistent shaking for 1 minute until it shut down. After a few minutes, I started it again and it started good but again idled very low and shook for a minute until it shut off. I was able to maintain higher idle without shaking as long as I kept my foot on the gas pedal....other wise it shut down as before.

Looks like I'm making some progress but still not right.



Offline Mattb

  • Pinto Member
  • **
  • Posts: 46
  • FeedBack: +3/-0
  • Another Pinto Driver

  • Total Badges: 1
    Badges: (View All)
    Fifth year Anniversary
Re: Starting issues again.......
« Reply #1 on: May 09, 2022, 06:20:21 PM »
Sounds like you would need to consider a stuck float in the carb or perhaps something blocking the needle from closing completely in the seat.