Current Classifieds

72 PINTO WAGON

Date: 09/23/2018 06:16 pm
1977 Pinto Cruising Wagon FOR SALE

Date: 08/20/2017 01:34 pm
1971 Pinto Runabout turn key driver

Date: 07/01/2019 12:23 pm
74 Pinto Rear Side Lights

Date: 02/18/2017 05:47 pm
4 speed pinto transmission

Date: 05/13/2021 05:29 pm
72 Pinto
Date: 03/07/2019 12:07 pm
Weber dcoe intake 2.0

Date: 08/01/2018 01:09 pm
Clutch Fork
Date: 03/31/2018 09:12 pm
V8 rear end
Date: 04/12/2018 10:57 am
Early V8 swap headers, damaged, fixable?
Date: 10/25/2019 03:30 pm
'79 4 speed manual shifter needed
Date: 07/30/2018 04:32 pm
1980 Ford Pinto Squire Wagon * All original 1 Owner *

Date: 09/15/2019 12:28 pm

« previous next »
Pages: [1]   Go Down

Author Topic: NOS question  (Read 730 times)

0 Members and 1 Guest are viewing this topic.

Offline caravan3921

  • Pinto Full Member
  • ***
  • Posts: 235
  • FeedBack: +0/-0
  • Gender: Female
  • Another Pinto Driver

    • Total Badges: 7
    Badges: (View All)
    Mobile User Poll Voter Topic Starter Tenth year Anniversary Windows User Apple User Fifth year Anniversary
NOS question
« on: September 12, 2018, 08:26:53 AM »
Where's a good place to go to find NOS parts for a pinto? What are some links or phone numbers to call to find parts for a 1978 Ford Pinto? I'm needing an accelerator pump diaphragm and I can't be certain if this part seen on eBay would fit exactly so I'm not going to go that route.
Logged

Offline LongTimeFordMan

  • PCCA VIP
  • Pinto Sr. Member
  • ***
  • Posts: 450
  • FeedBack: +182/-0
  • Gender: Male
  • 1973 Red Pinto Wagon

    • Total Badges: 6
    Badges: (View All)
    Fifth year Anniversary Topic Starter Signature Windows User Linux User Mobile User
Re: NOS question
« Reply #1 on: September 12, 2018, 10:28:13 AM »
Try Autozone,  O reilly, napa..  you will be surprised at the number of parts new or rebuilt that are still available for pintos since Ford tended to use the same parts across a lot of models including the mustang ii and ranger.. the weber 2 bbl was used from 71 till 92.. the only problems seem to be front suspension and brake parts for 71-73 models.. later models share a lot with the mii.
Logged
Red 1973 pinto wagon DD, SoCal desert car, Factory 4 speed, 3.40 gears, Stock engine, 14" rims and tires, 60 K original miles

Offline Wittsend

  • Pinto Master
  • *****
  • Posts: 2498
  • FeedBack: +241/-0

    • Total Badges: 8
    Badges: (View All)
    Tenth year Anniversary Mobile User Topic Starter Poll Voter 1000 Posts Linux User Windows User Fifth year Anniversary
Re: NOS question
« Reply #2 on: September 12, 2018, 11:10:44 AM »
Exactly. I just did a quick search and it seems the same diaphram was used on a large number of Ford products.  Dorman makes one. And most places if they don't carry Dorman can order from them.  BTW, you probably don't want NOS, but rather something newer what with the ethanol in gas today.

That said it will probably be an order item. The last carbureted engines available are at least 30 years old.
Logged

Offline LongTimeFordMan

  • PCCA VIP
  • Pinto Sr. Member
  • ***
  • Posts: 450
  • FeedBack: +182/-0
  • Gender: Male
  • 1973 Red Pinto Wagon

    • Total Badges: 6
    Badges: (View All)
    Fifth year Anniversary Topic Starter Signature Windows User Linux User Mobile User
Re: NOS question
« Reply #3 on: September 12, 2018, 01:00:56 PM »
Also.. you can probably find a rebuild kit for not much more than a special order diapbram... oreilly and napa seem to have more small parts... i even found the rubber seal ring for the thermostat at oreilly for less than a dollar.
Logged
Red 1973 pinto wagon DD, SoCal desert car, Factory 4 speed, 3.40 gears, Stock engine, 14" rims and tires, 60 K original miles

Offline LongTimeFordMan

  • PCCA VIP
  • Pinto Sr. Member
  • ***
  • Posts: 450
  • FeedBack: +182/-0
  • Gender: Male
  • 1973 Red Pinto Wagon

    • Total Badges: 6
    Badges: (View All)
    Fifth year Anniversary Topic Starter Signature Windows User Linux User Mobile User
Re: NOS question
« Reply #4 on: September 12, 2018, 01:06:55 PM »
Also  with respect to replacement "rebuilt" weber carburetors..  its probably to either rebuild r existing one or have it rebuilt.

The reason is that because there were so many varients of the carburetors for different models, it is probable that when they are factory rebuilt they may be fitted with incorrect jets. 

The PO of my car put a "rebuilt" carburetor and the jetting was all wrong. I never did get it running properly.
Logged
Red 1973 pinto wagon DD, SoCal desert car, Factory 4 speed, 3.40 gears, Stock engine, 14" rims and tires, 60 K original miles
Pages: [1]   Go Up
« previous next »