Current Classifieds

Holley 2305 progressive 2 bbl carb 350cfm

Date: 10/11/2019 11:13 am
New front rotors and everything for '74-'80
Date: 08/02/2019 04:18 pm
Need 72 pinto parts!
Date: 06/14/2019 01:40 pm
Wanted 2.3 engine mount brackets and mounts
Date: 02/14/2018 01:34 am
1980 Pinto Pony for sale

Date: 08/21/2021 03:54 pm
instrument cluster,4sd trans crossmember,2.3 intake
Date: 08/26/2018 06:23 pm
99' 2.5l lima cylinder head

Date: 01/13/2017 01:56 am
Rally spoiler wanted
Date: 05/04/2017 01:32 pm
78-80 Windshield
Date: 10/29/2021 03:11 pm
Center armrest for 1979 pinto . Possible anyone who makes them of has one for sale
Date: 08/13/2017 02:01 pm
Wanted 71-73 Pinto grill
Date: 03/09/2019 10:45 pm
1978 pinto brake booster needed.
Date: 04/07/2021 06:12 pm

« previous next »
Pages: [1]   Go Down

Author Topic: Side draft intake  (Read 855 times)

0 Members and 1 Guest are viewing this topic.

Offline stonhed18

  • Pinto Member
  • **
  • Posts: 21
  • FeedBack: +3/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Apple User Mobile User Windows User
Side draft intake
« on: August 31, 2018, 04:54:28 PM »
Using a duel side draft intake that blocks off the water jacket from the head. Getting some leakage. Has anyone had the same issue and solved it?


Sent from my iPhone using Tapatalk
Logged

Offline LongTimeFordMan

  • PCCA VIP
  • Pinto Sr. Member
  • ***
  • Posts: 450
  • FeedBack: +182/-0
  • Gender: Male
  • 1973 Red Pinto Wagon

    • Total Badges: 6
    Badges: (View All)
    Fifth year Anniversary Topic Starter Signature Windows User Linux User Mobile User
Re: Side draft intake
« Reply #1 on: September 08, 2018, 10:47:06 AM »
When I built my manifold I just drilled the mounting plate and tapped it to accommodate a 3/8"  rass pipe fitting so I could maintain the original heater water outlet. I tapped out a custom gasket from 1/16" grey Felpro gasket material and sealed it with black silicon.. no leaks so far..
Logged
Red 1973 pinto wagon DD, SoCal desert car, Factory 4 speed, 3.40 gears, Stock engine, 14" rims and tires, 60 K original miles

Offline stonhed18

  • Pinto Member
  • **
  • Posts: 21
  • FeedBack: +3/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Apple User Mobile User Windows User
Re: Side draft intake
« Reply #2 on: September 09, 2018, 07:22:28 AM »
Quote from: LongTimeFordMan on September 08, 2018, 10:47:06 AM
When I built my manifold I just drilled the mounting plate and tapped it to accommodate a 3/8"  rass pipe fitting so I could maintain the original heater water outlet. I tapped out a custom gasket from 1/16" grey Felpro gasket material and sealed it with black silicon.. no leaks so far..
I’ll try the custom gasket. The fitting is an issue. The runners on the intake angle back and upward interfering with alignment of the port. Thanks for the advice!


Sent from my iPhone using Tapatalk
Logged

Offline stonhed18

  • Pinto Member
  • **
  • Posts: 21
  • FeedBack: +3/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Apple User Mobile User Windows User
Re: Side draft intake
« Reply #3 on: September 09, 2018, 08:41:44 AM »



Sent from my iPhone using Tapatalk
Logged

Offline LongTimeFordMan

  • PCCA VIP
  • Pinto Sr. Member
  • ***
  • Posts: 450
  • FeedBack: +182/-0
  • Gender: Male
  • 1973 Red Pinto Wagon

    • Total Badges: 6
    Badges: (View All)
    Fifth year Anniversary Topic Starter Signature Windows User Linux User Mobile User
Re: Side draft intake
« Reply #4 on: September 09, 2018, 09:05:41 AM »
Have you had much experience with webbers?  Ive heard they are difficult to tune.. thats why i went with SU HIF s  only one needle per carburetor  and you can custom taper it with a hand drill and some 400 grit emory paper..

Also have you used a small wrench to tap out a gasket?
Logged
Red 1973 pinto wagon DD, SoCal desert car, Factory 4 speed, 3.40 gears, Stock engine, 14" rims and tires, 60 K original miles

Offline stonhed18

  • Pinto Member
  • **
  • Posts: 21
  • FeedBack: +3/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Apple User Mobile User Windows User
Re: Side draft intake
« Reply #5 on: September 10, 2018, 05:19:36 AM »
Quote from: LongTimeFordMan on September 09, 2018, 09:05:41 AM
Have you had much experience with webbers?  Ive heard they are difficult to tune.. thats why i went with SU HIF s  only one needle per carburetor  and you can custom taper it with a hand drill and some 400 grit emory paper..

Also have you used a small wrench to tap out a gasket?
No this is the first I’ve used any side draft. They seem to be working well.


Sent from my iPhone using Tapatalk
Logged

Offline LongTimeFordMan

  • PCCA VIP
  • Pinto Sr. Member
  • ***
  • Posts: 450
  • FeedBack: +182/-0
  • Gender: Male
  • 1973 Red Pinto Wagon

    • Total Badges: 6
    Badges: (View All)
    Fifth year Anniversary Topic Starter Signature Windows User Linux User Mobile User
Re: Side draft intake
« Reply #6 on: September 10, 2018, 04:31:27 PM »
Here are some pix of the manifold i built and the gasket altbough the gasket doesnt have the hole for the water port cut out yet..  the red line points to the water port. Also a detail of how I c9nnecter the water outlet to the heater. Note the tee with a connection allowing a mechanical temp sensor...
Logged
Red 1973 pinto wagon DD, SoCal desert car, Factory 4 speed, 3.40 gears, Stock engine, 14" rims and tires, 60 K original miles
Pages: [1]   Go Up
« previous next »