Current Classifieds

1978 need kick panels and rear hatch struts and upper and lower mounts
Date: 11/29/2018 10:26 am
Crankshaft Pulley
Date: 10/01/2018 05:00 pm
1978 ford pinto carb
Date: 02/04/2018 06:09 pm
74 Pinto Rear Side Lights

Date: 02/18/2017 05:47 pm
1973 Interior parts wanted
Date: 01/02/2017 11:02 pm
Wheel cap
Date: 04/25/2022 11:21 pm
1980 Ford Pinto Squire Wagon * All original 1 Owner *

Date: 09/15/2019 12:28 pm
Misc pinto parts 71-73 2.0
Date: 05/05/2020 11:56 pm
Chilton's Repair & Tune-up Guide 1971-1979 Pinto and Bobcat

Date: 03/06/2017 01:24 am
Weather Strip, Muffler, Splash Shields

Date: 02/21/2022 11:11 pm
1971 Pinto Runabout turn key driver

Date: 07/01/2019 12:23 pm
Pinto in Maine for sail...solid body

Date: 03/07/2017 07:03 pm

« previous next »
Pages: [1]   Go Down

Author Topic: Side draft intake  (Read 875 times)

0 Members and 1 Guest are viewing this topic.

Offline stonhed18

  • Pinto Member
  • **
  • Posts: 21
  • FeedBack: +3/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Apple User Mobile User Windows User
Side draft intake
« on: August 31, 2018, 04:54:28 PM »
Using a duel side draft intake that blocks off the water jacket from the head. Getting some leakage. Has anyone had the same issue and solved it?


Sent from my iPhone using Tapatalk
Logged

Offline LongTimeFordMan

  • PCCA VIP
  • Pinto Sr. Member
  • ***
  • Posts: 450
  • FeedBack: +182/-0
  • Gender: Male
  • 1973 Red Pinto Wagon

    • Total Badges: 6
    Badges: (View All)
    Fifth year Anniversary Topic Starter Signature Windows User Linux User Mobile User
Re: Side draft intake
« Reply #1 on: September 08, 2018, 10:47:06 AM »
When I built my manifold I just drilled the mounting plate and tapped it to accommodate a 3/8"  rass pipe fitting so I could maintain the original heater water outlet. I tapped out a custom gasket from 1/16" grey Felpro gasket material and sealed it with black silicon.. no leaks so far..
Logged
Red 1973 pinto wagon DD, SoCal desert car, Factory 4 speed, 3.40 gears, Stock engine, 14" rims and tires, 60 K original miles

Offline stonhed18

  • Pinto Member
  • **
  • Posts: 21
  • FeedBack: +3/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Apple User Mobile User Windows User
Re: Side draft intake
« Reply #2 on: September 09, 2018, 07:22:28 AM »
Quote from: LongTimeFordMan on September 08, 2018, 10:47:06 AM
When I built my manifold I just drilled the mounting plate and tapped it to accommodate a 3/8"  rass pipe fitting so I could maintain the original heater water outlet. I tapped out a custom gasket from 1/16" grey Felpro gasket material and sealed it with black silicon.. no leaks so far..
I’ll try the custom gasket. The fitting is an issue. The runners on the intake angle back and upward interfering with alignment of the port. Thanks for the advice!


Sent from my iPhone using Tapatalk
Logged

Offline stonhed18

  • Pinto Member
  • **
  • Posts: 21
  • FeedBack: +3/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Apple User Mobile User Windows User
Re: Side draft intake
« Reply #3 on: September 09, 2018, 08:41:44 AM »



Sent from my iPhone using Tapatalk
Logged

Offline LongTimeFordMan

  • PCCA VIP
  • Pinto Sr. Member
  • ***
  • Posts: 450
  • FeedBack: +182/-0
  • Gender: Male
  • 1973 Red Pinto Wagon

    • Total Badges: 6
    Badges: (View All)
    Fifth year Anniversary Topic Starter Signature Windows User Linux User Mobile User
Re: Side draft intake
« Reply #4 on: September 09, 2018, 09:05:41 AM »
Have you had much experience with webbers?  Ive heard they are difficult to tune.. thats why i went with SU HIF s  only one needle per carburetor  and you can custom taper it with a hand drill and some 400 grit emory paper..

Also have you used a small wrench to tap out a gasket?
Logged
Red 1973 pinto wagon DD, SoCal desert car, Factory 4 speed, 3.40 gears, Stock engine, 14" rims and tires, 60 K original miles

Offline stonhed18

  • Pinto Member
  • **
  • Posts: 21
  • FeedBack: +3/-0
  • Gender: Male
  • Another Pinto Driver

    • Total Badges: 4
    Badges: (View All)
    Topic Starter Apple User Mobile User Windows User
Re: Side draft intake
« Reply #5 on: September 10, 2018, 05:19:36 AM »
Quote from: LongTimeFordMan on September 09, 2018, 09:05:41 AM
Have you had much experience with webbers?  Ive heard they are difficult to tune.. thats why i went with SU HIF s  only one needle per carburetor  and you can custom taper it with a hand drill and some 400 grit emory paper..

Also have you used a small wrench to tap out a gasket?
No this is the first I’ve used any side draft. They seem to be working well.


Sent from my iPhone using Tapatalk
Logged

Offline LongTimeFordMan

  • PCCA VIP
  • Pinto Sr. Member
  • ***
  • Posts: 450
  • FeedBack: +182/-0
  • Gender: Male
  • 1973 Red Pinto Wagon

    • Total Badges: 6
    Badges: (View All)
    Fifth year Anniversary Topic Starter Signature Windows User Linux User Mobile User
Re: Side draft intake
« Reply #6 on: September 10, 2018, 04:31:27 PM »
Here are some pix of the manifold i built and the gasket altbough the gasket doesnt have the hole for the water port cut out yet..  the red line points to the water port. Also a detail of how I c9nnecter the water outlet to the heater. Note the tee with a connection allowing a mechanical temp sensor...
Logged
Red 1973 pinto wagon DD, SoCal desert car, Factory 4 speed, 3.40 gears, Stock engine, 14" rims and tires, 60 K original miles
Pages: [1]   Go Up
« previous next »