Current Classifieds

4 speed pinto transmission

Date: 05/13/2021 05:29 pm
73 2.0 Timing Crank Gear & Woodruff key WANTED
Date: 09/01/2017 07:52 am
Pinto porthole exterior trim wanted
Date: 03/30/2021 12:29 pm
1974 Pinto Passenger side door glass and door parts

Date: 02/28/2018 09:18 am
1978 RUNABOUT

Date: 04/01/2017 03:18 pm
4 speed pinto transmission

Date: 01/24/2021 07:54 pm
Wanted Dash for Pinto up to 1975
Date: 01/19/2020 09:06 am
74 Wagon Interior
Date: 01/22/2017 06:38 pm
Needed- Good 71-73 Rear End or parts- close to AL
Date: 09/15/2019 12:38 pm
72 pinto drag car

Date: 06/22/2017 07:19 am
1976 Ford Pinto Wagon - just rebuilt. 302 v8

Date: 11/11/2019 03:38 pm
Wanted - 71-73 Pinto grill
Date: 12/15/2016 03:32 pm

Author Topic: Schoenfeld headers  (Read 7486 times)

0 Members and 1 Guest are viewing this topic.

Offline LongTimeFordMan

  • PCCA VIP
  • Pinto Sr. Member
  • ***
  • Posts: 456
  • FeedBack: +182/-0
  • Gender: Male
  • 1973 Red Pinto Wagon

  • Total Badges: 6
    Badges: (View All)
    Fifth year Anniversary Topic Starter Signature Windows User Linux User Mobile User
Schoenfeld headers
« on: August 01, 2023, 04:43:09 AM »
Has anyone installed the shoenfeld headers from the special run on a 2.0 in a8 stock chassis pinto?

Do they require mods to the motor mounts
Red 1973 pinto wagon DD, SoCal desert car, Factory 4 speed, 3.40 gears, Stock engine, 14" rims and tires, 60 K original miles

Offline rob289c

  • Pinto Sr. Member
  • ****
  • Posts: 386
  • FeedBack: +7/-0
  • Gender: Male
  • Another Pinto Driver

  • Total Badges: 3
    Badges: (View All)
    Fifth year Anniversary Signature Topic Starter
Re: Schoenfeld headers
« Reply #1 on: August 01, 2023, 12:22:52 PM »
The header I bought but haven't tried out yet is: https://www.summitracing.com/parts/psm-72c1064
Not to highjack this thread but wondered if anyone has any experience with the one I bought, in addition to experience on the one that Long Time Form Man is asking about.  The one I got has a 2.5" Flanged collector.  Others I looked at were 3" open which I thought was too big for a street, stock 2.3. 

Looking forward to any feedback on all headers for 2.0 and 2.3. 
rob289c

Offline Milescabbathway

  • Pinto Driver
  • *
  • Posts: 2
  • FeedBack: +0/-0
  • Another Pinto Driver

  • Total Badges: 1
    Badges: (View All)
    Mobile User
Re: Schoenfeld headers
« Reply #2 on: April 13, 2024, 08:06:45 PM »
Yes!  Bolted right up with no other mods.  2.5 all the way back sounds great too

Offline rob289c

  • Pinto Sr. Member
  • ****
  • Posts: 386
  • FeedBack: +7/-0
  • Gender: Male
  • Another Pinto Driver

  • Total Badges: 3
    Badges: (View All)
    Fifth year Anniversary Signature Topic Starter
Re: Schoenfeld headers
« Reply #3 on: April 14, 2024, 05:52:24 AM »
I'm glad yours bolted right up.  On the Pacesetter header I bought, I had to heat and beat (basically flatten) the #3 tube to provide clearance between it and the right side frame rail.  I also had to remove and re-position the right side brace.  It looks cool but I wished it would have been a true bolt-on installation.  What I thought should take 15-30 minutes took the better part of an afternoon and it was in a fairly bare chassis!
rob289c

Offline fordblue72

  • Pinto Member
  • **
  • Posts: 36
  • FeedBack: +3/-0
  • Gender: Male
  • Another Pinto Driver

  • Total Badges: 7
    Badges: (View All)
    Tenth year Anniversary Fifth year Anniversary Topic Starter Poll Voter Apple User Mobile User Windows User
Re: Schoenfeld headers
« Reply #4 on: April 16, 2024, 08:47:59 AM »
My brother put that header on his 71 had to modify the mount but it worked out fine.