Current Classifieds

72 PINTO WAGON

Date: 09/23/2018 06:16 pm
1973 Pinto Runabout

Date: 03/25/2019 09:02 pm
74 Pinto Hub Caps & Trim Rings

Date: 02/18/2017 04:47 pm
77 pinto
Date: 08/22/2017 06:31 pm
postal pinto
Date: 06/03/2020 09:31 am
74 Wagon Interior
Date: 01/22/2017 06:38 pm
Looking for Radiator and gas tank
Date: 10/24/2018 07:35 am
2.3 turbo intake (lower)

Date: 07/15/2020 09:29 pm
Clutch Fork
Date: 03/31/2018 09:12 pm
Tire needed p185/80r13
Date: 12/31/2017 09:08 pm
74 Wagon body parts and a couple of 79 bits

Date: 11/14/2019 04:02 am
71-73 2.0 4 speed transmission wanted
Date: 09/06/2020 01:57 am

« previous next »
Pages: [1]   Go Down

Author Topic: 2.3L issue with idling  (Read 1513 times)

0 Members and 1 Guest are viewing this topic.

Offline MitchiePinto

  • Pinto Member
  • **
  • Posts: 76
  • FeedBack: +0/-0
  • Another Pinto Driver

    • Total Badges: 1
    Badges: (View All)
    Topic Starter
2.3L issue with idling
« on: September 05, 2012, 01:32:45 PM »
When I bought the car it was hard to start and had a leaking carb and idle was lumpy but it wouldn't quit and would run ok at about 500-650 rpm idle

Now I rebuilt the carb it starts easy but I have to keep my foot on the gas until it warms up (takes 6 mins) it idles at 2000 rpm when cold then around 1500 rpm when hot

The carb mixture is set lean (If I ran it richer it would bog out) Idle speed is set around 1500 rpm if I set it any lower the car would stall improperly

I suspect a vacuum leak (Il check with propane)

My carb is a 2100 Motorcraft without a choke mech.

Also I have a racing cam put into the head everything else in the engine bay is stock
Logged

Offline MitchiePinto

  • Pinto Member
  • **
  • Posts: 76
  • FeedBack: +0/-0
  • Another Pinto Driver

    • Total Badges: 1
    Badges: (View All)
    Topic Starter
Re: 2.3L issue with idling
« Reply #1 on: September 08, 2012, 03:26:46 PM »
UPDATE: Got the car running !!!!

The issue was the wrong power valve

In the kit it came with a 2 stage (I think) #28 power valve which made the car run rich and only stay running around 2000 rpm

I poped in my old power valve 1 stage #16 and fought with the float level until i got the smoothest idle

Now it idles around 500-750rpm (carb mixture screw's are set at 1 1/2 turns out )

No vacuum leaks, Car can handle slopes,loads and has no bogging or hesitating and the dieseling issue stopped

I have only the vacuum advance, PCV (from the air filter to the thing on top of the valve cover way in the back)

NOW one last issue the car has a mild lumpy idle like it wants to stall and if you listen closely you can hear a slight missfiring on idle and it vibrates some.

My hypothesis is that all this is being caused by the racing cam in it and I should check the ignition timing and advance the cam timing a little

Other than that the car is great it would do 100km all day long and Cruise fine its just the idle issue and I think it has an  overheating issue but im not sure. What are signs of overheating
Logged
Pages: [1]   Go Up
« previous next »